Sony Shower Mate ICF-S79 User manual

ICF-S79
FM/AM SYNTHESIZED RADIO
ICF-S79L
FM/MW/LW SYNTHESIZED RADIO
ICF-S79V
TV/WEATHER/FM/AM SYNTHESIZED RADIO
MICROFILM
US Model
ICF-S79V
AEP Model
ICF-S79/S79L
UK Model
ICF-S79L
SPECIFICATIONS
SERVICE MANUAL
ICF-S79/S79L/S79V
Photo: ICF-S79V
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

– 2 –
This section is extracted from
instruction manual. SECTION 1
GENERAL

– 3 –

– 4 –
Note: Follow the disassembly procedure in the numerical order given.
REAR CABINET
SECTION 2
DISASSEMBLY
2 six screws
(BTP 3
× 25)
1 battery case li
d
4 rear cabinet
5 antenna lead
5 BATT lead (red)
3 two claws
5 BATT lead (white)

FM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a reading on digital voltmeter.
L8 87.5 MHz (TV 2 ch) 2.3 ± 0.1 V (1.0 ± 0.1 V)
Confirm 108.0 MHz 8.5 ± 0.5 V (12.5 ± 0.5 V)
Note: Not use the FM RF signal generator in this adjustment.
( ): ICF-S79V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L6 87.5 MHz (TV 2 ch (59.75 MHz))
CT4 108.0 MHz
( ): ICF-S79V
ICF-S79L only
LW FREQUENCY COVERAGE ADJUSTMENT
Adjust for a reading on digital voltmeter.
CT5 153 kHz 2.3 ± 0.1 V
Confirm 279 kHz 8.5 ± 0.5 V
Note: Not use the AM RF signal generator in this adjustment.
ICF-S79L only LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L5 (LW side) 162 kHz
CT2 243 kHz
AM (MW) FREQUENCY COVERAGE ADJUSTMENT
Adjust for a reading on digital voltmeter.
L9 531 kHz (530 kHz) 2.8 ± 0.1 V
Confirm 1,602 kHz (1,710 kHz) 9.5 ± 0.5 V
Note: Not use the AM RF signal generator in this adjustment.
( ): ICF-S79V
AM (MW) TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L5 <MW side> 621 kHz (590 kHz)
CT3 1,395 kHz (1,490 kHz)
< >: ICF-S79L
( ): ICF-S79V
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T2 455 kHz
– 5 –
Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally done
by the trimmer capacitors.
SECTION 3
ELECTRICAL ADJUSTMENTS
[AM (LW/MW) Section]
Setting:
BAND switch: AM (MW) or LW
0dB=1 µV
[FM/TV Section]
Setting:
BAND switch: FM1 or TV
ICF-S79V only
TV FREQUENCY COVERAGE ADJUSTMENT
Adjust for a reading on digital voltmeter.
L2 WEATHER 2 ch 1.0 ± 0.1 V
Confirm TV 13 ch 10 ± 0.5 V
Note: Not use the FM RF signal generator in this adjustment.
ICF-S79V only TV TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1 WEATHER 2 ch (162.40 MHz)
CT1 TV 13 ch (215.75 MHz)
ICF-S79V only TV IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1 10.7 MHz
AM RF SSG
30% amplitude
modulation by
400 Hz signal
Output level: as low as possible
Put the lead-wire
antenna close to
the set.
+
–
level meter
speaker terminal
set
FM RF SSG
± 22.5 kHz frequency
deviation by 400 Hz
signal
Output level: as low as possible
+
–
level meter
speaker terminal
set
FM lead wire antenna terminal
0.01
µ F
+
–
digital voltmete
r
MAIN board
TP
(VT)

– 6 –
Adjustment and Connection Location:
FM antenna
ground
(JW17)
L8
FM FREQUENCY
COVERAGE
L9
AM (MW)
FREQUENCY
COVERAGE
L5 CT3
AM (MW)
TRACKING
TV TRACKING
(ICF-S79V only
)
T1
TV IF
(ICF-S79V only)
L2
TV FREQUENCY
COVERAGE
(ICF-S79V only)
CT5
LW FREQUENCY
COVERAGE
(ICF-S79L only)
TV antenna
ground
(JW20)
FM/TV
antenna input
(JW18)
CT1
L1
T2
AM IF
FM
TRACKING L6
CT4
CT2 L5
LW TRACKING
(ICF-S79L only)
MW LWL5
IC1
IC2
TP
(VT)
[MAIN BOARD] (Component Side)
[MAIN BOARD] (Conductor Side)

Note on PrintedWiring Board:
•: parts extracted from the component side.
•: indicates side identified with part number.
•¢: internal component.
•: Pattern from the side which enables seeing.
– 7 – – 8 –
ICF-S79/S79L/S79V
Mark Center frequency
red 10.70 MHz
blue 10.67 MHz
orange 10.73 MHz
black 10.64 MHz
white 10.76 MHz
HOW TO CHANGETHE CERAMIC FILTERS
This model is used two ceramic filters of CF1, CF3.
You must use same type of color marked ceramic filters in order to
meet same specifications.
Therefore, the ceramic filter must change two pieces together since
it's supply two pieces in one package as a spare parts.
mark
CF1
CF3
SECTION 4
DIAGRAMS
4-1. PRINTED WIRING BOARDS
Semiconductor Location
D1 G-1 Q1 F-1
D2 F-1 Q2 E-4
D3 E-2 Q3 I-6
D4 E-4 Q4 G-7
D5 H-2 Q5 E-6
D6 H-7 Q6 B-7
D7 G-6 Q7 H-6
D8 F-7 Q9 E-5
D9 E-2 Q10 D-6
D10 B-2 Q11 C-2
D11 B-2 Q12 A-2
D12 C-7 Q13 D-7
D13 C-7 Q14 C-7
D14 H-7 Q15 D-2
Q16 D-1
IC1 F-2 Q17 A-3
IC2 E-7
IC3 C-7
IC4 C-6
IC5 C-6
IC6 B-5
Ref. No. Location Ref. No. Location

– 9 – – 10 –
ICF-S79/S79L/S79V
Note on Schematic Diagram:
•All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•¢: internal component.
•: panel designation.
• B+ : B+ Line.
•: adjustment for repair.
•Power voltage is dc 4.5 V and fed with regulated dc power
supply from battery terminal.
•Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM (TV 2 – 6 ch)
( ) :AM (MW)
[]:LW
4-2. SCHEMATIC DIAGRAM (ICF-S79/S79L) •See page 11 for Waveforms and IC Block Diagrams.
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
•Circled numbers refer to waveforms.
•Signal path.
: FM
: AM (MW/LW)

4-3. SCHEMATIC DIAGRAM (ICF-S79V) •See page 11 forWaveforms and IC Block Diagrams.
– 11 – – 12 –
Note on Schematic Diagram:
•Allcapacitorsare in µF unless otherwisenoted. pF:µµF50
WV or less are not indicated except for electrolytics and
tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•¢:internal component.
•: panel designation.
•: B+ Line.
•:adjustment for repair.
•Power voltage is dc 4.5V and fed with regulated dc power
supply from battery terminal.
•Voltages and waveforms are dc with respect to ground un-
der no-signal (detuned) conditions.
no mark : FM (TV 2 – 6 ch)
( ) : AM
<< >> :TV (7 – 13 ch)
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
•Circled numbers refer to waveforms.
•Signal path.
: FM
: AM
:TV
ICF-S79/S79L/S79V

– 13 –
•Waveforms
1IC6 @∞ (XIN)
2 Vp-p
13.3 µ s
2IC6 #¡ – #¢ (COM0 – COM3)
3 Vp-p
32 ms
3IC6 #∞ – $• (LCD0 – LCD13)
3 Vp-p
32 ms
4D11 ANODE
440 ns
30 Vp-p
5Q11-1 COLLECTOR
6 Vp-p
360 ns
• IC Block Diagrams
IC1 TA7358P (ICF-S79V only)
12 3 45 6 7 8 9
RF
AMP
REGULATOR
BIAS
MIX OSC
RF IN
BYPASS
RF OUT
MIX
GND
MIX OUT
OSC OUT
OSC
VCC
12 3 45 6 7 8 9 10 1514131211
FM
DISCRIMINATOR
AF POWER AMP AM FE FM IF
TUNING
METER
AM IF DET AGC
FM FE
23 22 21 202425 19 18 17 1629 28 27 2630
GND GND AF OUT VCC RIPPLE FILTER AF IN DET OUT AFC AGC AFC AGC IF GND METER N.C FM IF IN AM IF IN FM/AM BAND SELECT
FM/AM
IF OUT
N.C
FE GND
AM RF IN
FM RF
REG OUT
FM OSC
FM RF IN
AFC
AM OSC
VOL
NF
FM DISCRI
GND GND

– 14 –
Pin No. Pin Name I/O Function
1 INIT OUT O Initialize signal output for the destination select
2 POWER O Radio power on/off control signal output “H”: power on
3 MUTE O Mute on/off control signal output “L”: mute on
4 AL LEVEL O Beep sound level variable output terminal Not used (open)
5NCO
Not used (open)
6 to 9 KS0 to KS3 O Key strobe signal output terminal
10 to 13 KR0 to KR3 I Key return signal input terminal
14 BAND1 O Band select signal output terminal *1
15 BAND2 O Band select signal output terminal *1
Used for ICF-S79L/S79V only (ICF-S79: not used (open))
16 V AMP — Power supply terminal for buffer amplifier
17 NC O Not used (open)
18 GND — Ground terminal
19 EO O PLL error signal output terminal
20 VCOL I AM (MW) or LW VCO input terminal
21 VCOH I FM, TV or WEATHER VCO input terminal
22 VREG1 — Power supply terminal (connected to the coupling capacitor)
23 VDD — Power supply terminal (+2.2 V)
24 XOUT O System clock output terminal (75 kHz)
25 XIN I System clock input terminal (75 kHz)
26 VREG2 — Power supply terminal (connected to the coupling capacitor)
27 VLCD0 —
28 CAP0 —
29 CAP1 —
30 VLCD2 —
31 to 34 COM0 to COM3 O Common drive signal output to the liquid crystal display (LCD1)
35 to 48 LCD0 to LCD13 O Segment drive signal output to the liquid crystal display (LCD1)
49 LCD14 O Segment drive signal output terminal Not used (open)
50 CE I Power failure detection signal input from the IC5 Normally: “H”
51 INT I Not used (fixed at “L”)
52 BEEP O Beep sound drive signal output terminal
53 VDET I Power failure detection signal input from the IC4 Normally: “H”
54 PB1 I Initialize signal input for the destination select Fixed at “L”
55 PB2 I Initialize signal input for the destination select
ICF-S79/S79L: initialize mode at “H”, ICF-S79V: fixed at “L”
56 PB3 I Initialize signal input for the destination select
ICF-S79L: initialize mode at “H”, ICF-S79/S79V: fixed at “L”
MAIN BOARD IC6 µPD17071GB-517-1A7
(SYSTEM CONTROLLER, LIQUID CRYSTAL DISPLAY CONTROLLER, KEY CONTROL)
Terminal for doubler circuit capacitor connection to develop liquid crystal display drive
voltage
*1 Band select signal
FM (TV L) TV H/
WEATHER AM (MW) LW
BAND1 (pin !¢)“L” “L” “H” “H”
BAND2 (pin !∞)“L” “H” “L” “H”
4-4. IC PIN FUNCTION DESCRIPTION

– 15 –
SECTION 5
EXPLODED VIEW
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delayshould be anticipated when ordering these
items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Accessories and packing materials are given in
the last of the electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
mayhavesome differencefromthe original one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑↑
Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
not supplied
not supplied
not supplied
LCD1
SP1
11
1
2
3
4
6
7
89
10
12
13
14 15
16
17
18
1 X-3374-190-1 CABINET (FRONT) ASSY (S79V)
1 X-3374-190-2 CABINET (FRONT) ASSY (S79L)
1 X-3374-190-3 CABINET (FRONT) ASSY (S79)
2 3-016-880-01 PLATE (BUTTON), SHEET (S79V)
2 3-016-880-11 PLATE (BUTTON), SHEET (S79/S79L)
*3 3-016-863-01 CHASSIS
*4 A-3679-918-A MAIN BOARD, COMPLETE (S79)
*4 A-3679-919-A MAIN BOARD, COMPLETE (S79V)
*4 A-3679-921-A MAIN BOARD, COMPLETE (S79L)
6 3-016-875-01 SHEET (BATTERY) (A)
7 3-016-869-01 TERMINAL (+), BATTERY
8 3-016-861-01 CABINET (REAR)
9 3-016-871-01 TERMINAL (+.–) (A), BATTERY
10 3-016-872-01 TERMINAL (+.–) (B), BATTERY
11 3-016-870-01 TERMINAL (–), BATTERY
12 7-685-152-19 SCREW +BTP 3X25 TYPE2 N-S
13 3-016-876-01 SHEET (BATTERY) (B)
14 3-368-852-01 FOOT
15 3-016-862-01 LID, BATTERY CASE
16 3-016-867-01 SPRING, SP
17 3-016-873-01 SPRING, RING
18 3-016-864-01 KNOB (VOL)
SP1 1-504-918-11 SPEAKER (7.7CM)
LCD1 1-801-854-11 DISPLAY PANEL, LIQUID CRYSTAL

– 16 –
SECTION 6
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts speci-
fied in the diagrams or the components used on
the set.
• -XX and -X mean standardized parts, so they
mayhavesomedifference from the originalone.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when order-
ing these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Ref. No. Part No. Description Remark
KEY
When indicating parts by reference
number, please include the board.
KEY BOARD (INCLUDED MAIN BOARD)
**********
< SWITCH >
S101 1-554-303-21 SWITCH, TACTILE (RADIO ON)
S102 1-554-303-21 SWITCH, TACTILE
(PRESET TUNIG/PRESET TIMER 1)
S103 1-554-303-21 SWITCH, TACTILE
(PRESET TUNIG/PRESET TIMER 2)
S104 1-554-303-21 SWITCH, TACTILE
(PRESET TUNIG/PRESET TIMER 3)
S105 1-554-303-21 SWITCH, TACTILE
(PRESET TUNIG/PRESET TIMER 4)
S106 1-554-303-21 SWITCH, TACTILE
(PRESET TUNIG/PRESET TIMER 5)
S107 1-554-303-21 SWITCH, TACTILE (BAND)
S108 1-554-303-21 SWITCH, TACTILE (WEATHER) (S79V)
S109 1-554-303-21 SWITCH, TACTILE (TIMER SET/ON/OFF)
S110 1-554-303-21 SWITCH, TACTILE (TUNE/TIMER ADJUST +)
S111 1-554-303-21 SWITCH, TACTILE (TUNE/TIMER ADJUST –)
S112 1-554-303-21 SWITCH, TACTILE (CLOCK)
S113 1-554-303-21 SWITCH, TACTILE (OFF)
************************************************************
*A-3662-876-A MAIN BOARD, COMPLETE (S79)
*A-3662-879-A MAIN BOARD, COMPLETE (S79V)
*A-3662-888-A MAIN BOARD, COMPLETE (S79L)
(INCLUDING KEY BOARD)
**********************
*3-016-863-01 CHASSIS
< BAND PASS FILTER >
BPF1 1-236-711-21 FILTER, BAND PASS (S79/S79L)
BPF1 1-239-813-21 FILTER, BAND PASS (S79V)
BPF2 1-233-521-11 FILTER, BAND PASS (S79V)
< CAPACITOR/CHIP CONDUCTOR >
C1 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C2 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C3 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
(S79V)
C4 1-163-217-11 CERAMIC CHIP 1PF 0.25PF50V
(S79V)
C5 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C6 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C7 1-163-085-00 CERAMIC CHIP 2PF 0.25PF50V
(S79V)
C8 1-163-231-11 CERAMIC CHIP 15PF 5% 50V
(S79V)
C9 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C10 1-163-217-11 CERAMIC CHIP 1PF 0.25PF50V
(S79V)
C11 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
(S79V)
C12 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
(S79V)
C13 1-124-584-00 ELECT 100uF 20% 10V
(S79V)
C14 1-164-232-11 CERAMIC CHIP 0.01uF 50V
(S79V)
C15 1-164-232-11 CERAMIC CHIP 0.01uF 50V
(S79V)
C16 1-164-232-11 CERAMIC CHIP 0.01uF 50V
(S79V)
C19 1-216-295-00 CONDUCTOR, CHIP (2012)
C21 1-163-118-00 CERAMIC CHIP 110PF 5% 50V
(S79L)
C22 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
(S79L)
C23 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C24 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C25 1-216-295-91 CONDUCTOR, CHIP (2012)
C26 1-104-396-11 ELECT 10uF 20% 16V
C27 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
(S79V)
C27 1-216-295-00 CONDUCTOR, CHIP (2012) (S79/S79L)
C28 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C29 1-163-085-00 CERAMIC CHIP 2PF 0.25PF50V
C30 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C31 1-163-125-00 CERAMIC CHIP 220PF 5% 50V
C32 1-163-085-00 CERAMIC CHIP 2PF 0.25PF50V
C33 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
MAIN

– 17 –
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C34 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C35 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C36 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
C37 1-163-128-00 CERAMIC CHIP 300PF 5% 50V
(S79L)
C38 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C39 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C40 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C41 1-164-346-11 CERAMIC CHIP 1uF 16V
C42 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C43 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C44 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C45 1-126-163-11 ELECT 4.7uF 20% 50V
C46 1-104-396-11 ELECT 10uF 20% 16V
C47 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C48 1-164-346-11 CERAMIC CHIP 1uF 16V
C49 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
(S79L)
C50 1-123-618-11 ELECT 22uF 20% 6.3V
C51 1-126-925-11 ELECT 470uF 20% 10V
C52 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C53 1-135-091-00 TANTALUM CHIP 1uF 20% 16V
C54 1-126-925-11 ELECT 470uF 20% 10V
C56 1-104-396-11 ELECT 10uF 20% 16V
C57 1-164-346-11 CERAMIC CHIP 1uF 16V
C58 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C59 1-164-346-11 CERAMIC CHIP 1uF 16V
C60 1-163-125-00 CERAMIC CHIP 220PF 5% 50V
C61 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C62 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
C63 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C64 1-126-916-11 ELECT 1000uF 20% 6.3V
C65 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C66 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C67 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C68 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C69 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C70 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C71 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C72 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C73 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C74 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C75 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C76 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C77 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C78 1-113-677-11 CERAMIC CHIP 1uF 25V
C79 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C80 1-163-108-00 CERAMIC CHIP 43PF 5% 50V
C81 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
C82 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C83 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C84 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C85 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C86 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C87 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C90 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C92 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C93 1-164-232-11 CERAMIC CHIP 0.01uF 50V
(S79L/S79V)
C95 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C96 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
(S79V)
C98 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
(S79V)
C99 1-163-229-11 CERAMIC CHIP 12PF 5% 50V
(S79V)
C100 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C101 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C102 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C104 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C105 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C106 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< CERAMIC FILTER >
CF1 1-577-324-11 FILTER, CERAMIC
CF2 1-577-072-21 FILTER, CERAMIC (S79/S79V)
CF2 1-578-677-21 FILTER, CERAMIC (S79L)
CF3 1-577-324-11 FILTER, CERAMIC
< TRIMMER >
CT1 1-141-304-21 CAP, TRIMMER 10PF (S79V)
CT2 1-141-245-00 CAP, TRIMMER 30PF (S79L)
CT3 1-141-304-21 CAP, TRIMMER 10PF
CT4 1-141-304-21 CAP, TRIMMER 10PF
CT5 1-141-260-00 CAP, TRIMMER 50PF (S79L)
< DIODE/CHIP CONDUCTOR >
D1 8-713-100-11 DIODE 1T362 (S79V)
D2 8-713-100-11 DIODE 1T362 (S79V)
D3 8-719-421-40 DIODE MA77 (S79V)
D4 8-719-988-62 DIODE 1SS355 (S79V)
D5 8-719-800-76 DIODE 1SS226
D6 8-719-951-05 DIODE KV1560 (S79/S79V)
D7 8-713-100-11 DIODE 1T362 (S79/S79L)
D7 8-719-002-81 DIODE 1T363 (S79V)
D8 8-713-100-11 DIODE 1T362 (S79/S79L)
D8 8-719-002-81 DIODE 1T363 (S79V)
D9 1-216-295-00 CONDUCTOR, CHIP (2012) (S79/S79L)
D9 8-719-421-40 DIODE MA77 (S79V)
D10 8-719-977-40 DIODE UDZ-TE-17-13B (S79/S79L)
D10 8-719-977-49 DIODE UDZ-TE-17-15B (S79V)
D11 8-719-988-62 DIODE 1SS355
D12 8-719-941-04 DIODE SB007-03CP
D13 8-719-988-62 DIODE 1SS355
D14 8-719-023-99 DIODE KV1563M-3 (S79L)
< IC >
IC1 8-759-204-01 IC TA7358P (S79V)
IC2 8-752-055-05 IC CXA1019S
IC3 8-759-255-04 IC S-81220PG-PS-T1
IC4 8-759-480-31 IC S-80832ANNP-EDW-T2
IC5 8-759-466-70 IC S-80827ANNP-EDQ-T2
IC6 8-759-474-42 IC uPD17071GB-517-1A7
MAIN

– 18 –
< CHIP CONDUCTOR >
JC1 1-216-295-00 CONDUCTOR, CHIP (2012) (S79L/S79V)
JC3 1-216-296-00 CONDUCTOR, CHIP (3216)
JC4 1-216-296-00 CONDUCTOR, CHIP (3216)
JC5 1-216-295-00 CONDUCTOR, CHIP (2012) (S79V)
JC6 1-216-295-00 CONDUCTOR, CHIP (2012)
JC7 1-216-295-00 CONDUCTOR, CHIP (2012) (S79/S79V)
JC8 1-216-296-00 CONDUCTOR, CHIP (3216)
JC9 1-216-295-00 CONDUCTOR, CHIP (2012)
JC10 1-216-295-00 CONDUCTOR, CHIP (2012)
JC11 1-216-296-00 CONDUCTOR, CHIP (3216)
JC13 1-216-296-00 CONDUCTOR, CHIP (3216) (S79V)
JC14 1-216-296-00 CONDUCTOR, CHIP (3216)
JC15 1-216-295-00 CONDUCTOR, CHIP (2012)
JC16 1-216-296-00 CONDUCTOR, CHIP (3216)
JC17 1-216-296-00 CONDUCTOR, CHIP (3216)
JC18 1-216-296-00 CONDUCTOR, CHIP (3216)
JC19 1-216-296-00 CONDUCTOR, CHIP (3216) (S79L)
JC21 1-216-295-00 CONDUCTOR, CHIP (2012)
JC23 1-216-295-00 CONDUCTOR, CHIP (2012) (S79/S79L)
JC25 1-216-295-00 CONDUCTOR, CHIP (2012) (S79L)
JC26 1-216-295-00 CONDUCTOR, CHIP (2012)
JC27 1-216-295-00 CONDUCTOR, CHIP (2012)
< COIL >
L1 1-416-501-11 COIL, AIR-CORE (TV RF) (S79V)
L2 1-402-966-11 COIL (TV OSC) (S79V)
L5 1-501-722-11 ANTENNA, FERRITE-ROD (AM) (S79/S79V)
L5 1-501-723-11 ANTENNA, FERRITE-ROD (MW/LW) (S79L)
L6-1 1-416-459-11 COIL, AIR-CORE (FM RF)
L6-2 1-428-229-11 COIL, AIR-CORE (FM RF) (S79V)
L6-2 1-428-290-11 COIL, AIR-CORE (FM RF) (S79/S79L)
L8 1-406-922-11 COIL, AIR-CORE (FM OSC)
L9 1-406-485-11 COIL (AM OSC)
L10 1-412-937-11 INDUCTOR 0.68uH
L11 1-412-951-11 INDUCTOR 10uH
L12 1-412-937-11 INDUCTOR 0.68uH (S79V)
L13 1-412-937-11 INDUCTOR 0.68uH (S79V)
L15 1-408-982-11 INDUCTOR 100uH
L17 1-412-951-11 INDUCTOR 10uH
L18 1-410-204-31 INDUCTOR CHIP 10uH
< LIQUID CRYSTAL DISPLAY >
LCD1 1-801-854-11 DISPLAY PANEL, LIQUID CRYSTAL
< TRANSISTOR >
Q1 8-729-102-07 TRANSISTOR 2SC2223-F13 (S79V)
Q2 8-729-102-07 TRANSISTOR 2SC2223-F13 (S79V)
Q3 8-729-102-07 TRANSISTOR 2SC2223-F13 (S79L)
Q4 8-729-904-87 TRANSISTOR 2SB1197K-R (S79V)
Q5 8-729-102-07 TRANSISTOR 2SC2223-F13
Q6 8-729-027-39 TRANSISTOR DTA144TKA-T146
Q7 8-729-901-73 TRANSISTOR 2SC2412K (S79L)
Q9 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q10 8-729-921-72 TRANSISTOR 2SD1781K-R (S79L)
Q11 8-729-402-19 TRANSISTOR XN6501
Q12 8-729-402-19 TRANSISTOR XN6501
Q13 8-729-904-87 TRANSISTOR 2SB1197K-R
Q14 8-729-027-60 TRANSISTOR DTC144TKA-T146
Q15 8-729-216-22 TRANSISTOR 2SA1162-G (S79V)
Q16 8-729-901-73 TRANSISTOR 2SC2412K (S79V)
Q17 8-729-102-07 TRANSISTOR 2SC2223-F13
< RESISTOR/CHIP CONDUCTOR >
R1 1-216-097-00 METAL CHIP 100K 5% 1/10W
(S79V)
R2 1-216-097-00 METAL CHIP 100K 5% 1/10W
(S79V)
R3 1-216-009-00 METAL CHIP 22 5% 1/10W
(S79V)
R4 1-216-109-00 METAL CHIP 330K 5% 1/10W
(S79V)
R5 1-216-097-00 METAL CHIP 100K 5% 1/10W
(S79V)
R6 1-216-109-00 METAL CHIP 330K 5% 1/10W
(S79V)
R7 1-216-049-11 METAL CHIP 1K 5% 1/10W
(S79V)
R8 1-216-025-00 METAL CHIP 100 5% 1/10W
(S79V)
R9 1-216-041-00 METAL CHIP 470 5% 1/10W
(S79V)
R10 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
(S79V)
R11 1-216-105-00 METAL CHIP 220K 5% 1/10W
(S79V)
R12 1-216-073-00 METAL CHIP 10K 5% 1/10W
(S79V)
R13 1-216-025-00 METAL CHIP 100 5% 1/10W
(S79V)
R14 1-216-097-00 METAL CHIP 100K 5% 1/10W
(S79L)
R15 1-216-097-00 METAL CHIP 100K 5% 1/10W
R16 1-216-097-00 METAL CHIP 100K 5% 1/10W
R17 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
(S79V)
R18 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R19 1-216-097-00 METAL CHIP 100K 5% 1/10W
R20 1-216-097-00 METAL CHIP 100K 5% 1/10W
R21 1-216-089-00 METAL CHIP 47K 5% 1/10W
R22 1-216-037-00 METAL CHIP 330 5% 1/10W
R23 1-216-073-00 METAL CHIP 10K 5% 1/10W
(S79V)
R24 1-216-073-00 METAL CHIP 10K 5% 1/10W
(S79V)
R25 1-216-073-00 METAL CHIP 10K 5% 1/10W
R26 1-216-121-00 METAL CHIP 1M 5% 1/10W
R28 1-216-049-11 METAL CHIP 1K 5% 1/10W
R29 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R30 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
(S79L)
R31 1-216-049-11 METAL CHIP 1K 5% 1/10W
R32 1-216-021-00 METAL CHIP 68 5% 1/10W
R33 1-216-295-00 CONDUCTOR, CHIP (2012)
R35 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R36 1-216-037-00 METAL CHIP 330 5% 1/10W
R38 1-216-097-00 METAL CHIP 100K 5% 1/10W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN

– 19 –
R39 1-216-089-00 METAL CHIP 47K 5% 1/10W
R40 1-216-105-00 METAL CHIP 220K 5% 1/10W
R41 1-216-049-11 METAL CHIP 1K 5% 1/10W
R42 1-216-097-00 METAL CHIP 100K 5% 1/10W
R43 1-216-073-00 METAL CHIP 10K 5% 1/10W
R44 1-216-073-00 METAL CHIP 10K 5% 1/10W
R45 1-216-097-00 METAL CHIP 100K 5% 1/10W
R46 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R47 1-216-073-00 METAL CHIP 10K 5% 1/10W
(S79V)
R48 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
(S79V)
R49 1-216-121-00 METAL CHIP 1M 5% 1/10W
R50 1-216-121-00 METAL CHIP 1M 5% 1/10W
R51 1-216-073-00 METAL CHIP 10K 5% 1/10W
R52 1-216-073-00 METAL CHIP 10K 5% 1/10W
R53 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R54 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R55 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R56 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R57 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R58 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R59 1-216-049-11 METAL CHIP 1K 5% 1/10W
(S79L/S79V)
R60 1-216-121-00 METAL CHIP 1M 5% 1/10W
(S79L)
R61 1-216-097-00 METAL CHIP 100K 5% 1/10W
R62 1-216-033-00 METAL CHIP 220 5% 1/10W
R63 1-216-001-00 METAL CHIP 10 5% 1/10W
R64 1-216-073-00 METAL CHIP 10K 5% 1/10W
R65 1-216-001-00 METAL CHIP 10 5% 1/10W
R66 1-216-049-11 METAL CHIP 1K 5% 1/10W
R67 1-216-097-00 METAL CHIP 100K 5% 1/10W
R68 1-216-097-00 METAL CHIP 100K 5% 1/10W
R69 1-216-097-00 METAL CHIP 100K 5% 1/10W
R70 1-216-097-00 METAL CHIP 100K 5% 1/10W
R71 1-216-097-00 METAL CHIP 100K 5% 1/10W
R72 1-216-097-00 METAL CHIP 100K 5% 1/10W
R73 1-216-097-00 METAL CHIP 100K 5% 1/10W
R74 1-216-097-00 METAL CHIP 100K 5% 1/10W
R75 1-216-097-00 METAL CHIP 100K 5% 1/10W
R76 1-216-097-00 METAL CHIP 100K 5% 1/10W
R77 1-216-097-00 METAL CHIP 100K 5% 1/10W
R78 1-216-097-00 METAL CHIP 100K 5% 1/10W
R79 1-216-097-00 METAL CHIP 100K 5% 1/10W
R80 1-216-097-00 METAL CHIP 100K 5% 1/10W
R81 1-216-097-00 METAL CHIP 100K 5% 1/10W
R82 1-216-097-00 METAL CHIP 100K 5% 1/10W
R83 1-216-097-00 METAL CHIP 100K 5% 1/10W
R84 1-216-097-00 METAL CHIP 100K 5% 1/10W
R85 1-216-073-00 METAL CHIP 10K 5% 1/10W
R86 1-216-089-00 METAL CHIP 47K 5% 1/10W
R87 1-216-073-00 METAL CHIP 10K 5% 1/10W
R89 1-216-025-00 METAL CHIP 100 5% 1/10W
R93 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
(S79L)
< VARIABLE RESISTOR >
RV1 1-225-550-11 RES, VAR, CARBON 50K (VOL)
< TRANSFORMER >
T1 1-403-872-00 TRANSFORMER, IF (TV IF) (S79V)
T2 1-404-790-11 TRANSFORMER, IF (AM IF) (S79/S79V)
T2 1-404-902-41 TRANSFORMER, IF (AM IF) (S79L)
T3 1-449-138-11 TRANSFORMER, DC-DC CONVERTER
< VIBRATOR >
X1 1-767-517-11 VIBRATOR, CRYSTAL (75kHz)
************************************************************
MISCELLANEOUS
***************
SP1 1-504-918-11 SPEAKER (7.7CM)
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
3-917-356-01 SUCKER
3-860-702-11 MANUAL, INSTRUCTION
(ENGLISH, FRENCH, GERMAN, ITALIAN)
3-860-702-21 MANUAL, INSTRUCTION
(DUTCH, SWEDISH, SPANISH, PORTUGUESE)
3-860-702-31 MANUAL, INSTRUCTION (FINNISH, DANISH)
X-3897-401-1 STRAP ASSY (S79V)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN