Sony STR-DA3300ES - Multi Channel Av Receiver User manual

SERVICE MANUAL
AUDIO POWER
SPECIFICATIONS
(US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
PO
DA3300ES: US and Canadian models/
DG1100:
WER OUTPUT
Rated Power Output at Stereo Mode1) 2)
(8 ohms 20 Hz – 20 kHz,
THD 0.09%):
100 W + 100 W
Reference Power Output at Stereo Mode
(4 ohms 20 Hz – 20 kHz,
THD 0.15%):
85 W + 85 W
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
FRONT2):
110 W + 110 W
CENTER2): 110 W
SURROUND2):
110 W + 110 W
SUR BACK2):
110 W + 110 W
Reference Power Output
(4 ohms 1 kHz, THD 0.7%)
FRONT2):
100 W + 100 W
CENTER2): 100 W
SURROUND2):
100 W + 100 W
SUR BACK2):
100 W + 100 W
1)Depending on the sound field settings and the
source, there may be no sound output.
2)Measured under the following conditions:
Power requirements: 120 V AC, 60 Hz
Frequency response
PHONO RIAA equalization curve
±0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV
VIDEO 1/2/3
10 Hz – 100 kHz
±3 dB
Rated Po
DA3300ES: AEP, Russian, Ukrainian and
UK models:
wer Output at Stereo Mode1) 2)
(8 ohms 1 kHz, THD
0.7%):
105 W + 105 W
Reference Power Output at Stereo Mode2)
(4 ohms 1 kHz, THD
0.7%):
105 W + 105 W
Reference Power Output
(8 ohms 20 Hz – 20 kHz,
THD 0.09%)
FRONT2):
100 W + 100 W
CENTER2):
100 W
SURROUND2):
100 W + 100 W
SURROUND BACK2):
100 W + 100 W
Reference Power Output
(4 ohms 20 Hz – 20 kHz,
THD 0.7%)
FRONT2):
100 W + 100 W
CENTER2):
100 W
SURROUND2):
100 W + 100 W
SURROUND BACK2):
100 W + 100 W
Reference Power Output at Stereo Mode
(8 ohms 1 kHz, THD
10%):
130 W + 130 W
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD
10%):
130 W + 130 W
MULTI CHANNEL AV RECEIVER
SPECIFICATIONS
STR-DA3300ES/DG1100
Ver. 1.2 2007.10
– Continued on next page –
9-887-742-03
2007J05-1
© 2007.10
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
US Model
STR-DA3300ES/DG1100
Canadian Model
AEP Model
UK Model
STR-DA3300ES
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
*Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS”, “DTS-ES” and “Neo:6” are registered trademarks of DTS, Inc. “DTS 96/24” is a trademark of DTS, Inc.
Photo: STR-DA3300ES

2
STR-DA3300ES/DG1100
AM tuner section
Tuning range
With 10-kHz tuning scale
530 – 1,710 kHz
3)
With 9-kHz tuning scale
531 – 1,710 kHz
3)
Antenna (aerial) Loop antenna (aerial)
3)
You can change the AM tuning scale to either 9
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
HDMI Video
Input/Output (HDMI Repeater block)
640 ×480p@60 Hz
720 ×480p@59.94/60 Hz
1440 ×480p@59.94/60 Hz (pixel sent 2times)
1280 × 720p@59.94/60 Hz
1920 × 1080i@59.94/60 Hz
1920 ×1080p@59.94/60 Hz
720 ×576p@50 Hz
1440 ×576p@50 Hz (pixel sent 2times)
1280 ×720p@50 Hz
1920 ×1080i@50 Hz
1920 ×1080p@50 Hz
1920 ×1080p@24 Hz
General
Po
DA3300ES: US and Canadian models/DG1100:
wer requirements
Power output (DIGITAL MEDIA PORT)
DC OUT
120 V AC, 60 Hz
DA3300ES: AEP, Russian, Ukrainian and
UK models: 230 V AC, 50/60 Hz
(in countries/area in
Europe other than the U.K.)
230 – 240 V AC, 50/60 Hz
(in the U.K. and general area)
DA3300ES: US and Canadian models/DG1100:
350 W/480 VA (US/Canada)
DA3300ES: AEP, Russian, Ukrainian and
UK models: 390 W
: 5 V, 700 mA
Power consumption
Power consumption (during standby mode)
0.7 W (when “HDMI
Control” and “RS-232C
Control” are set to “OFF”)
Dimensions 430 ×175 ×430 mm
(width/height/depth)
including projecting parts
and controls
Mass (Approx.) 14.5 kg
Supplied accessories
Operating Instructions
Quick Setup Guide (1)
HDMI CONTROL Guide (1)
GUI Menu List (1)
Optimizer microphone ECM-AC2 (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
AC power cord (mains lead) (1) (DA3300ES)
Remote commander RM-AAL011 (1)
(DA3300ES: US and Canadian models)
Remote commander RM-AAP019 (1)
(DA3300ES: AEP, Russian, Ukrainian and UK models)
(DA3300ES)
Remote commander RM-AAU018 (1)
(DG1100)
Remote commander RM-AAP018 (1)
R6 (size-AA) batteries
(4 (DA3300ES) or 2 (DG1100))
Design and specifications are subject to
change without notice.
Inputs (Analog)
Inputs (Digital)
Outputs
PHONO Sensitivity: 2.5 mV
Impedance: 50 kohms
S/N: 90 dB (A, 20 kHz
LPF)
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
Sensitivity: 150 mV
Impedance: 50 kohms
S/N:100dB (A,20kHz
LPF)
DVD/BD,VIDEO 2,
SA-CD/CD (Coaxial) Impedance: 75 ohms S/N: 96 dB (A, 20 kHz
LPF)
VIDEO 1, VIDEO 3,
SAT/CATV, TV,
MD/TAPE (Optical)
S/N: 96 dB
(A, 20 kHz LPF)
MD/TAPE (REC OUT),
VIDEO 1 (AUDIO OUT) Voltage:150 mV Impedance: 1 kohm
FRONT L/R, CENTER,
SURROUND L/R,
SUR BACK L/R, SUB
WOOFER
Voltage: 2 V
Impedance: 1 kohm
EQUALIZER
Gain levels ±10 dB, 1 dB step
FM tuner section
Tuning range 87.5 – 108.0 MHz
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Reference Power Output
(8 ohms 1 kHz, THD 10%)
FRONT
2)
:
130 W + 130 W
CENTER
2)
:
130 W
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
2)
:
130 W + 130 W
Reference Power Output
(4 ohms 1 kHz, THD 10%)
FRONT
2)
:
130 W + 130 W
CENTER
2)
:
130 W
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
2)
:
130 W + 130 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 230 V AC, 50/60 Hz
(in countries/area in Europe
other than the U.K.)
240 V AC, 50/60 Hz
(in the U.K. and general
area)
Frequency response
PHONO RIAA equalization curve
±0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
10 Hz – 100 kHz
±3 dB
Tu
DA3300ES: AEP, Russian, Ukrainian and
UK models:
DA3300ES: US and Canadian models/DG1100:
ning range 531 – 1,602 kHz
(With 9-kHz tuning scale)
Antenna (aerial) Loop antenna (aerial)
Ver. 1.2

3
STR-DA3300ES/DG1100
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Checkthe antenna terminals, metaltrim, “metallized”knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedAC voltmeter. The “limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passiveVOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground

4
STR-DA3300ES/DG1100
TABLE OF CONTENTS
1. SERVICING NOTES .............................................. 5
2. GENERAL .................................................................. 11
3. DISASSEMBLY
3-1. Disassembly Flow .......................................................... 16
3-2. Case ................................................................................ 17
3-3. Front Panel Block ........................................................... 17
3-4. CIS Board (DA3300ES: US and Canadian models),
Tuner (FM/AM).............................................................. 18
3-5. D_AUDIO Board, DSP Board........................................ 18
3-6. TUNER Board, CONTROL Board ................................ 19
3-7. PREOUT Board (DA3300ES), SUB WOOFER
Board (DG1100) and S_SPTM Board............................ 19
3-8. D_VIDEO Board ............................................................ 20
3-9. A_VIDEO Board ............................................................ 20
3-10. MAIN Board, C_SPTM Board....................................... 21
3-11. AC Board, Power Transformer (T001) ........................... 22
3-12. Power AMP Block .......................................................... 22
4. TEST MODE............................................................. 23
5. ELECTRICAL ADJUSTMENTS ........................ 27
6. DIAGRAMS
6-1. Block Diagram – CONTROL Section – ......................... 28
6-2. Block Diagram – DSP Section – .................................... 29
6-3. Block Diagram – HDMI Section –................................. 30
6-4. Block Diagram – VIDEO PROCESS Section – ............. 31
6-5. Block Diagram – ANALOGAUDIO Section – ............. 32
6-6. Block Diagram – POWER AMP Section – .................... 33
6-7. Block Diagram – VIDEO Section – ............................... 34
6-8. Block Diagram – PANEL, CIS, XM/
SIRIUS RECEIVER, DMPORT Section – .................... 35
6-9. Block Diagram – POWER SUPPLY Section – .............. 36
6-10. Printed Wiring Board
– D_AUDIO Board (Component Side) – ....................... 38
6-11. Printed Wiring Board
– D_AUDIO Board (Conductor Side) – ......................... 39
6-12. Schematic Diagram – D_AUDIO Board (1/4) – ............ 40
6-13. Schematic Diagram – D_AUDIO Board (2/4) – ............ 41
6-14. Schematic Diagram – D_AUDIO Board (3/4) – ............ 42
6-15. Schematic Diagram – D_AUDIO Board (4/4) – ............ 43
6-16. Printed Wiring Board
– TUNER Board (Component Side) – ........................... 44
6-17. Printed Wiring Board
– TUNER Board (Conductor Side) – ............................. 45
6-18. Schematic Diagram – TUNER Board (1/2) – ................ 46
6-19. Schematic Diagram – TUNER Board (2/2) – ................ 47
6-20. Printed Wiring Board – DSP Board – ............................ 48
6-21. Schematic Diagram – DSP Board – ............................... 49
6-22. Printed Wiring Boards – CONNECTOR Section –........ 50
6-23. Schematic Diagram – CONNECTOR Section – ............ 51
6-24. Printed Wiring Board
– TEMPERATURE DETECTION BOARD – ............... 52
6-25. Schematic Diagram
– TEMPERATURE DETECTION BOARD – ............... 52
6-26. Printed Wiring Board – A CLASSAMP Board – .......... 53
6-27. Schematic Diagram – A CLASS AMP Board (1/2) – .... 54
6-28. Schematic Diagram – A CLASS AMP Board (2/2) – .... 55
6-29. Printed Wiring Board – POWERAMP Board – ............ 56
6-30. Schematic Diagram – POWER AMP Board – ............... 57
6-31. Printed Wiring Board – PROTECTOR (F-C) Board – ... 58
6-32. Schematic Diagram – PROTECTOR (F-C) Board – ...... 59
6-33. Printed Wiring Boards
– PROTECTOR (SB/SURR) Section – .......................... 60
6-34. Schematic Diagram
– PROTECTOR (SB/SURR) Section – .......................... 61
6-35. Printed Wiring Board – BIAS Board –........................... 62
6-36. Schematic Diagram – BIAS Board – ............................. 63
6-37. Printed Wiring Boards – SPEAKER Section – .............. 64
6-38. Schematic Diagram – SPEAKER Section –................... 65
6-39. Printed Wiring Boards – PREOUT Section – ................ 66
6-40. Schematic Diagram – PREOUT Section –..................... 67
6-41. Schematic Diagram – MAIN Board (1/4) – ................... 68
6-42. Schematic Diagram – MAIN Board (2/4) – .................... 69
6-43. Schematic Diagram – MAIN Board (3/4) – ................... 70
6-44. Schematic Diagram – MAIN Board (4/4) – ................... 71
6-45. Printed Wiring Board – MAIN Board – ......................... 72
6-46. Schematic Diagram – D_VIDEO Board (1/9) – ............ 73
6-47. Schematic Diagram – D_VIDEO Board (2/9) – ............ 74
6-48. Schematic Diagram – D_VIDEO Board (3/9) – ............ 75
6-49. Schematic Diagram – D_VIDEO Board (4/9) – ............ 76
6-50. Schematic Diagram – D_VIDEO Board (5/9) – ............ 77
6-51. Schematic Diagram – D_VIDEO Board (6/9) – ............ 78
6-52. Schematic Diagram – D_VIDEO Board (7/9) – ............ 79
6-53. Schematic Diagram – D_VIDEO Board (8/9) – ............ 80
6-54. Schematic Diagram – D_VIDEO Board (9/9) – ............ 81
6-55. Printed Wiring Board
– D_VIDEO Board (Component Side) – ....................... 82
6-56. Printed Wiring Board
– D_VIDEO Board (Conductor Side) – ......................... 83
6-57. Printed Wiring Board
– A_VIDEO Board (Component Side) –........................ 84
6-58. Printed Wiring Board
– A_VIDEO Board (Conductor Side) – ......................... 85
6-59. Schematic Diagram – A_VIDEO Board (1/4) –............. 86
6-60. Schematic Diagram – A_VIDEO Board (2/4) –............. 87
6-61. Schematic Diagram – A_VIDEO Board (3/4) –............. 88
6-62. Schematic Diagram – A_VIDEO Board (4/4) –............. 89
6-63. Printed Wiring Board –VIDEO3 Board –...................... 90
6-64. Schematic Diagram – VIDEO3 Board – ........................ 91
6-65. Printed Wiring Board
– CONTROL Board (Component Side) – ...................... 92
6-66. Printed Wiring Board
– CONTROL Board (Conductor Side) –........................ 93
6-67. Schematic Diagram – CONTROL Board (1/2) – ........... 94
6-68. Schematic Diagram – CONTROL Board (2/2) – ........... 95
6-69. Printed Wiring Board – CIS Board
(DA3300ES: US and Canadian models) – ..................... 96
Ver. 1.1

5
STR-DA3300ES/DG1100
6-70. Schematic Diagram – CIS Board
(DA3300ES: US and Canadian models) – ..................... 97
6-71. Printed Wiring Board – DISPLAY Board – ................... 98
6-72. Schematic Diagram – DISPLAY Board – ...................... 99
6-73. Printed Wiring Boards – PANEL Section –.................... 100
6-74. Schematic Diagram – PANEL Section – ........................ 101
6-75. Printed Wiring Board – DC-DC Board – ....................... 102
6-76. Schematic Diagram – DC-DC Board – .......................... 103
6-77. Printed Wiring Board – AC Board –............................... 104
6-78. Schematic Diagram – AC Board – ................................. 105
7. EXPLODED VIEWS
7-1. Case Section ................................................................... 146
7-2. DISPLAY Board Section................................................ 147
7-3. Front Panel Section ........................................................ 148
7-4. AC/DC-DC Boards Section............................................ 149
7-5. D_AUDIO/D_VIDEO Boards Section........................... 150
7-6. A_VIDEO Board Section ............................................... 151
7-7. Heat Sink Section ........................................................... 152
7-8. MAIN Board Section...................................................... 153
8. ELECTRICAL PARTS LIST............................... 154
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
•MODEL IDENTIFICATION
Model PART No.
DA3300ES:AEP model 3-113-925-0[]
DA3300ES: UK model 3-113-925-1[]
DA3300ES: US and Canadian models 3-113-925-2[]
DG1100 3-113-925-3[]
DA3300ES: Russian and Ukrainian models 3-113-925-6[]
NOTE OF REPLACING THE IC3511 AND IC3513 ON
THE D_VIDEO BOARD
IC3511 and IC3513 on the D_VIDEO board cannot exchange with
single. When IC3511 and IC3513 on the D_VIDEO board are
damaged, exchange the entire mounted board.
NOTE OF REPLACING THE IC3601 ON THE
D_VIDEO BOARD
Replacement of IC3601 on the D_VIDEO board used in this set
requires a special tool.
PART No.
– Back Panel –
Ver. 1.2
Note: Refer to SUPPLEMENT-1 for the A_VIDEO and AC boards
ofprintedwiring boards,schematic diagramsandelectrical
parts list of DA3300ES: AEP, Russian, Ukrainian and UK
models.
Refer to SUPPLEMENT-1/SUPPLEMENT-2 for the MAIN
board of printed wiring board, schematic diagrams and
electrical parts list of DA3300ES: AEP and UK models.
Refer to SUPPLEMENT-2 fortheMAIN andTUNER boards
ofprintedwiring boards,schematic diagramsandelectrical
parts list of DA3300ES: Russian and Ukrainian models.
When repairing the set of DA3300ES:US, Canadian, AEP
and UK models/DG1100, refer to either of original service
manual/SUPPLEMENT-1/SUPPLEMENT-2 according tothe
set.

6
STR-DA3300ES/DG1100
UPDATE OF SOFTWARE OF IC2003 ON THE CONTROL BOARD AND IC3610 ON THE D_VIDEO BOARD
Perform operation of the following when the update of software of the IC2003 on the CONTROL board and IC3610 on the D_VIDEO board
is necessary.
•DA3300ES: US and Canadian models
Connect:
for PC
J881
Procedure:
1. Connect J881 on the CIS board and PC by using the RS-232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J881 on the CIS board and PC.
•DA3300ES: AEP, Russian, Ukrainian and UK models/DG1100
Connect:
Procedure:
1. Remove the KNOB (VOL) ASSY and connect CN717 on the MAIN VOL board and PC by using the jig.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the jig from the CN717 on the MAINVOL board and PC.
JIG
(Part No. : J-2501-300-A)
for PC CN717
MAIN VOL board
ERROR MESSAGES
If there is a malfunction, the display shows a code of two numbers and a message. You can check the condition of the system by the
message. Refer to the following table to solve the problem.
messages cause and response
PROTECTOR Irregular current is output to the speakers, or the upper panel of the receiver is covered with something.
The receiver will automatically turn off after a few seconds. Cheack the speakers connection and turn
on the power again.
Ver. 1.2

7
STR-DA3300ES/DG1100
POWER AMP BLOCK SERVICE POSITION
In checking the PowerAMP block, prepare jig (extension cable J-2501-291-A: 2 mm Pitch, 12 cores, Length 300 mm/J-2501-311-A: 2 mm
Pitch, 15 cores, Length 300 mm).
insulating sheet
Connect the extension jig (J-2501-311-A) to the
A CLASS AMP board (CN1505) and
CONNECTOR 4 board (CN1207).
CONNECTOR 4 board
(CN1207)
A CLASS AMP board
(CN1505)
power AMP Block
Connect the extension jig (J-2501-291-A) to the
A CLASS AMP board (CN1504) and
CONNECTOR 3 board (CN1202). CONNECTOR 3 board
(CN1202)
A CLASS AMP board
(CN1504)
MAIN BOARD SERVICE POSITION
insulating sheet
MAIN board
In checking the board, make two
capacitors discharge for electric
shock prevention. (R: 800 Ω/2W)
C1237
C1237
C1137
C1137
CAUTION

8
STR-DA3300ES/DG1100
LEAD WIRE SETTING
heat sink
The lead wire must not come in contact with the transformer and the heat sink.
transformer
Please band together so that a primary side cable
cannot touch a power transformer and heat sink.

STR-DA3300ES/DG1100
99
STR-DA3300ES/DG1100
SECTION 2
GENERAL This section is extracted from
instruction manual.
Description and location of parts
(DA3300ES: US and Canadian models)
Getting Started
Front panel
To remove the cover
Press PUSH.
When you remove the cover, keep it out
of reach from children.
Status of the POWER button
Off
The receiver is turned off (initial
setting).
Press POWER to turn the receiver on.
You cannot turn the receiver on using
the remote.
On/Standby
Press ?/1on the remote to turn the
receiver on or set it to the standby mode.
When you press POWER on the
receiver, the receiver will be turned off.
Name Function
APOWER Press to turn the
receiver on or off.
BAUTO CAL MIC
jack Connects to the supplied optimizer
microphone for the
Digital Cinema Auto
Calibration function.
CTONE MODE Adjusts FRONT/
CENTER/
SURROUND/
SURROUND BACK
BASS and TREBLE.
Press TONE MODE
repeatedly to select
BASS or TREBLE,
then turn TONE to
adjust the level.
TONE
DMEMORY/
ENTER Press to operate a tuner (FM/AM) and satellite
radio (XM/SIRIUS).
TUNING MODE
TUNING
ERemote sensor Receives signals from
remote commander.
FDIMMER Press repeatedly to
adjust brightness of the
display.
Name Function Name Function
NPHONES jack Connects to
headphones.
OSPEAKERS
(OFF/A/B/A+B) Switch to OFF, A, B, A+B of the front
speakers.
PVIDEO 3 IN/
PORTABLE AV
IN jacks
Connect to a portable
audio/videocomponent
such as a camcorder or
video game.
QMULTI
CHANNEL
DECODING
lamp
Lights up when multi-
channel audio signals
are decoded.
RINPUT
SELECTOR Turn to select the input source to play back.
To select the input
source for zone 2, press
ZONE/SELECT (
qa
)
to select zone 2 first
(“ZONE 2 INPUT”
appearsonthedisplay),
then turn INPUT
SELECTOR to select
the input source.
SMASTER
VOLUME Turn to adjust the volume level of all
speakers at the same
time.
HSUR BACK
DECODING Press to activate SB DECODING.
IDisplay
window The current status of theselected component
or a list of selectable
items appears here.
J2CH/A.DIRECT Press to select sound
field.
A.F.D.
MOVIE
MUSIC
KZONE/
POWER,
SELECT
Press SELECT
repeatedly to select
zone 2 or main zone.
Each time you press
POWER, the output
signals for the selected
zone will be turned on
or off.
LDMPORT Press to select the
audio/video input
signal from the
component connected
to the DIGITAL
MEDIA PORT adapter.
GDISPLAY Press repeatedly to
select information
displayed on the
display.
MHDMI Press to select input
source from the
component connected
to the HDMI IN jack.
Rear panel
ADIGITAL INPUT/OUTPUT section
OPTICAL IN/
OUT jacks Connect to a DVD player, Super Audio
CD player, etc. The
COAXIAL jack
provides a better
quality sound.
COAXIAL IN
jacks
HDMI IN/
OUT* jacks Connect to a DVD player, Blu-ray Disc
Player, or a satellite
tuner. An image and
the sound are output
to TV or a projector.
BANTENNA section
FMANTENNA
jack Connects to the FM wire antenna (aerial)
supplied with this
receiver.
AM
ANTENNA
jack
Connects to the AM
loop antenna (aerial)
supplied with this
receiver.
XM jack Connects to the XM
Mini Tuner and
Home Dock (not
supplied).
SIRIUS jack Connects to a
SiriusConnect Home
tuner (not supplied).
CRS-232C port
Used for
maintenance and
service.
*You can watch the selectedinput image whenyou
connect the MONITOR VIDEO OUT jack to a TV.
You can operate this receiver using a GUI (Graphi
cal User Interface).
DDMPORT
Connects to a Sony
DIGITAL MEDIA
PORT adapter.
EControl jack for Sony equipment
and other external components
CTRL S IN/
OUT jacks Connect to Sony TV,
DVD player or VCR
with CONTROL S
jack.
TRIGGER
OUT jack Connectstointerlock on/off of the power
supply of other 12V
TRIGGER
compliant
components, or the
amplifier/receiver of
zone 2.
IR REMOTE
IN/OUT jacks Connect an IR repeater.
FCOMPONENT VIDEO INPUT/
OUTPUT section
Y, P
B
/C
B
, P
R
/
C
R
IN/OUT*
jacks
Connect to a DVD
player, TV, or a
satellite tuner.
MULTI
CHANNEL
INPUT jacks
Connect to a Super
Audio CD player or
DVD player with an
analog audio jack for
7.1 channel or 5.1
channel sound.
PRE OUT jacks Connect to an
external power
amplifier.
HVIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
OUT jacks Connect to a VCR or a DVD player etc.
VIDEO IN/
OUT* jacks
AUDIO OUT
jacks
VIDEO OUT
jack
Connect to the
component in zone 2.
ISPEAKERS section
Connectstospeakers.
GAUDIO INPUT/OUTPUT section
AUDIO IN/
OUT jacks Connect to a tape deckorMDdeck, etc.
Ver. 1.1

STR-DA3300ES/DG1100
1010
STR-DA3300ES/DG1100
You can use thesuppliedremoteRM-AAL011
to operate the receiver and to control the Sony
audio/video components that the remote is
assigned to operate.
RM-AAL011
Remote commander
Name Function
CInput
buttons Press one of the buttons to select the component you want
to use. Press a pink-labeled
button after pressing SHIFT
(wk).When youpress anyofthe
input buttons, the receiver turns
on. The buttons are factory
assigned to control Sony
components. You can program
the remote to control non-Sony
components following the steps
in “Programming the remote”.
DZONE 2 Press to enable the zone 2
operation.
GMUSIC Press to select sound field.
HMOVIE Press to select sound field.
INumeric
buttons Press to –preset/tune to preset stations.
–select track numbers of the
CD player, DVD player, Blu-
ray Disc Player or MD deck.
Press 0/10 to select track
number 10.
–select channel numbers of
the VCR or satellite tuner.
–After pressing TV (e;),
press the numeric buttons to
select the TV channels.
JENTER Press to enter the value after
selecting a channel, disc or
track using the numeric buttons.
MEMORY Press to store a station during
tuner operation.
KAMP MENU Press to displaythe menu to
operate the receiver.
L
V/v/B/b
Press V/v/B/bto select the
menu items. Then press to
enter the selection.
MOPTIONS Press to display and select items
from option menus for receiver
and DVD player, Blu-ray Disc
Player.
TOOLS Press to display andselect items
from the option menus for DVD
player or Blu-ray Disc Player,
etc.
NMENU Press to display themenu to
operate the audio/video
components.
SCREEN/
DSPL
CONTROL
Press SHIFT (wk), then press
MENU to switch the display
mode of the menu between
SCREEN (to display the menu
onthe TV screen) and DSPL (to
display the menu in the display
window).
OCATEGORY
+/– Press to select the category for satellite tuner.
Name Function
Pm/M
a)
x
a)
X
a)
H
a) b)
./>
a)
Press to operate the DVD
player, Blu-ray Disc Player, CD
player, MD deck, tape deck, or
component connected to the
DIGITAL MEDIA PORT
adapter etc.
CATEGORY
MODE Press to select the category mode for satellite tuner.
TUNING +/– Press to select station.
QPRESET
+
b)
/– Press to register FM/AM/ satellite tuner stations or to
select preset stations.
TV CH +/– Press TV (e;), then press TV
CH +/– to operate the TV,
satellite tuner, VCR, etc.
RF1/F2 Press TV (e;), then press F1 or
F2 to select a component to
operate.
•HDD recorder
F1: HDD
F2: DVD player, Blu-ray Disc
Player
•DVD/VHS combo player
F1: DVD player, Blu-ray Disc
Player
F2: VHS
MACRO1,
MACRO2 Press AMP (6), then press MACRO1 or MACRO2 to set
up the macro function.
TV/INPUT Press TV/INPUT and TV (e;)
at the same time to select the
input signal (TV input or video
input).
a)
See the table for information on the buttons that
you can use to control each component.
b)
The tactile dot is attached to these buttons (H,
PRESET+). Use as a mark of operation.
Notes
•Some functions explained in this section may not
work depending on the model.
•The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
SDVD/
TOP MENU,
MENU
Press to display the menus of
the DVD player on the TV
screen. Then use V/v/B/band
to perform a menu
operations.
NIGHT
MODE Press AMP (6), then press NIGHT MODE to activate the
NIGHT MODE function.
INPUT
MODE Press AMP (6), then press INPUT MODE to select the
input mode when the same
components are connected to
both digital and analog jacks.
TMUTING Press to turn off the sound
temporarily. Press the button
again to restore the sound.
UMASTER
VOL +/– Press to adjust the volume level of all speakers at the same time.
TV VOL +/– Press TV (e;), then press TV
VOL +/– to adjust the volume
level of the TV.
VDISC SKIP Press to skip a disc when using
a multi-disc changer.
WRETURN/
EXIT OPress to return to the previous menu or exit the menu whilethe
menu or on-screen guide of the
VCR, DVD player, or satellite
tuner is displayed on the TV
screen.
XDISPLAY Press to select information
displayed in the display
window, TVscreen of the VCR,
satellite tuner, CDplayer, DVD
player, Blu-ray Disc Player, or
MD deck.
Note
Inthe SCREENmode, press the
button to display the menu on
the TV screen.
YCLEAR Press to
–clear a mistake when you
press the incorrect numeric
button.
–return to continuous
playback, etc. of the satellite
tuner or DVD player.
>10 Press to select
–track numbers over 10 of the
VCR, satellite tuner, CD
player or MD deck.
–channel numbers of the
Digital CATV terminal.
D.TUNING Press to enter direct tuning
mode.
Z2CH/
A.DIRECT Press to select sound field or to switch the audio
of the selected input to analog
signal without any adjustment.
wj A.F.D. Press to select sound field.
wk SHIFT Press to light up the button. It
changes the remote button
function to activate the buttons
with pink printing.
wl SLEEP Press to activate the sleep timer
function and the duration which
the receiver turns off
automatically.
e; TV Press to enable the TV
operation.
ea RM SET UP Press to set up the remote.
Name Function
AAV ?/1(on/
standby) Press to turn on or off the audio/ video components that the
remote is assigned to operate.
If you press the ?/1(B) at the
same time, it willturn off the
receiver and other Sony
components (SYSTEM
STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
button (C).
B?/1(on/
standby) Press to turn the receiver on or off.
If ZONE 2 is selected, only the
main receiveris turned on or off
with this button. To turn off all
components including an
amplifier in zone 2, press ?/1
and AV ?/1(A) at the same
time (SYSTEM STANDBY).
FAMP Press to enable the receiver
operation.
ETEST TONE Press to output the test tone
from each speaker.
WIDE Press repeatedly to select the
wide picture mode.
RESOLUTION Press SHIFT (wk) then press
RESOLUTION repeatedly to
change the resolution of signals
output from the HDMI OUT or
COMPONENT VIDEO
MONITOR OUT jack.
RM-AAU018
This remote can only be used to operate the
receiver. You can control the main functionsof
the receiver with simple operations using this
remote.
Name Function
A?/1(on/
standby) Press to turn a receiver on or off.
B2CH/
A.DIRECT Press to select sound field.
A.F.D.
MOVIE
MUSIC
CSCREEN/
DSPL
CONTROL
Press to switch the display
mode of the menu between
SCREEN (to display the menu
onthe TV screen) and DSPL (to
display the menu in the display
window).
D
V/v/B/b
After pressing SCREEN/DSPL
CONTROL (3), press V/v/B/
bto select the menu items.
Then press to enter the
selection.
EOPTIONS Pressto display and select items
from option menus.
FMENU Press to display the menu to
operate the receiver.
GDMPORT Press to operate component
connected to the DIGITAL
MEDIA PORT adapter.
NStarts play.
xStops play.
./>Skips tracks.
HINPUT
SELECTOR Press to select the input source to play back.
IMASTER
VOLUME +/– Press to adjust the volume level.
JMUTING Press to turn off the sound
temporarily. Press the button
again to restore the sound.
KRETURN/
EXIT Press to return to the previous menu or exit the menu.
LDISPLAY Press to select information
displayed in the display
window.
Note
In the SCREENmode, press the
button to display the menu on
the TV screen.
MSLEEP Press to activate the sleep timer
function and the duration which
the receiver turns off
automatically.
Name Function