Sony RM-VZ950T User manual

3-223-637-11 (1)
Remote Commander
© 2000 Sony Corporation
RM-VZ950T
Operating Instructions
Bedienungsanleitung
GB
DE

2GB
Table of Contents
Features ................................................................................................... 4
Getting Started
Installing the Batteries ............................................................................ 5
When to replace the batteries ....................................................................... 5
Location of Controls ................................................................................ 6
About the LCD display ................................................................................. 7
How to use the Jog dial ................................................................................. 7
Basic Operations
Setting the Component Codes ................................................................. 8
Setting by entering the code number .......................................................... 8
Setting by searching ...................................................................................... 11
Operating Your Components with the Remote Commander ................. 13
Operating a component .............................................................................. 13
Controlling the volume ............................................................................... 15
Operating Non-Preset Components — Learning Function .................... 15
Programming a component signal ............................................................ 15
For accurate Learning .................................................................................. 18
Programming the input select for the amplifier ...................................... 19
Changing or erasing the function of a “learned” button ....................... 21
Advanced Features
Changing the Component Selection Order (MOVE) ............................... 24
Changing the Name of the Component (NAME) .................................... 26
Erasing All Memorised Settings (DELETE) .............................................. 30
Erasing all memorised settings from a Setting position number .......... 30
Erasing all memorised settings from the Commander
— Factory Reset ......................................................................................... 31
Turning Off the LCD (DISP) ..................................................................... 33
Setting the time for the LCD to turn off .................................................... 33
Additional Information
Precautions ............................................................................................ 35
Specifications......................................................................................... 35
Troubleshooting ..................................................................................... 36

3GB
GB
Appendix
Table of Preset Functions ....................................................................... 38
TV ................................................................................................................... 38
SAT ................................................................................................................. 39
VCR ................................................................................................................ 39
DVD ............................................................................................................... 40
CD .................................................................................................................. 40
MD.................................................................................................................. 41
TAPE .............................................................................................................. 41
AMP ............................................................................................................... 41
Index ...................................................................................................... 42

4GB
Features
The RM-VZ950T Remote Commander provides centralised control of all
your AV components from a single remote commander and saves the
trouble of operating different AV components with different remote
control devices. The following are its main features.
Centralised control of Sony AV components with this one remote
commander
This Commander is preset at the factory to operate Sony brand
components, so you can use it out of the box as a control centre for your
Sony AV components.
Remote control signals for non-Sony components are also preset
This Commander is preset for most major brands components including
Sony. You can remote control your components by setting their code
numbers (page 8).
Learning function for programming other remote control signals
you need
This Commander has a Learning function, to “learn” remote control
signals to operate non-preset components or functions (page 15).
In addition, the Commander can “learn” remote control signals (infrared
signals only) of non-Audio Visual components such as air-conditioners,
lights, etc. (some specific appliances or functions may not be available)
(page 18).
Reassigning new components
You can assign Setting position numbers to freely operate other
components. This is useful when you have more than two of the same
kind of AV components (page 8).
LCD display and Jog dial for easy monitoring and operation
This Commander has an LCD display that shows the current component
to operate, or the current status during setup (page 7). With the Jog dial,
you can easily select a function to operate, or confirm a setting at various
setup procedures (page 7).
Customisable function display
You can freely change the names of components as you would want to
call them on the display (page 26).
Universal remote commander of high-quality design and material
We carefully designed this universal Commander so that it coordinates
with your living room interior.
The CE mark on the unit is valid only for products marketed
in the European Union.

5GB
Getting Started
Installing the
Batteries
Slide open the battery
compartment lid and insert two
R6 (size AA) alkaline batteries (not
supplied). Be sure to match the +
and – ends on the batteries to the
diagram inside the battery
compartment.
When to replace the
batteries
Under normal conditions, the
batteries will last up to three
months. When the batteries are
worn out, the LCD display turns
off about ten seconds after you
press any control button. When
you press a button, the LCD
display turns on, and “BATT”
appears in the display. When this
happens, replace the batteries with
new ones.
If you want to save the
batteries
The LCD display of this
Commander usually displays the
last used component name. To
save the batteries, you can also set
the display to turn off while the
Commander is not in use. See
“Turning Off the LCD (DISP)” on
page 33 for details.
Notes on batteries
• Do not mix old batteries with new
ones or mix different types of
batteries together.
• If the electrolyte inside the battery
should leak, wipe the contaminated
area of the battery compartment with
a cloth and replace the old batteries
with new ones. To prevent the
electrolyte from leaking, remove the
batteries when you plan not to use
the Commander for a long period of
time.
• The Commander still holds the
memorised settings even after you
change the batteries. To erase the
memory, see “Erasing All Memorised
Settings (DELETE)” on page 30.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position. When you close the
compartment lid, make sure to fix
its position first.

6GB
Location of Controls
1/(Text) button
2t(Input) button
3Number buttons
4-/-- (1-) button
5Colour buttons
(Red, Green, Yellow, Blue)
6LCD display
7MENU zbutton
8Jog dial
92(Volume) +/– buttons*
0(Mute) button*
qa SET button
qs 1(Power) button
qd a(TV) button
qf 2- button
qg b/B/v/V (Cursor) buttons or
N/x/m/M (Player
control) buttons
qh OK Xbutton
qj PROGR (Programme) +/–
buttons
qk (Recall) button
*Note on the 2+/– and
buttons
The Commander controls or mutes
the TV’s volume when you select a
visual component. The Commander
controls or mutes the amplifier’s
volume when you select an audio
component.
Note
The function of control buttons vary
depending on settings/operating
modes.
“Table of Preset Functions” (page 38)
shows how the Commander generally
operates for each component at preset
mode.
These settings can be changed, and
some buttons are used specifically in
the setup procedure as described in the
following pages.
PRESET
DELETE
EXIT
LEARN
DISP.
MOVE
NAME

7GB
About the LCD display
The LCD (Liquid Crystal Display)
displays the component in
operation or the current status of
the Commander as shown below.
It also has a backlight that lights
up when you turn or push the Jog
dial during component operations
(does not light up at SET modes).
When a remote control signal is
sent, appears in the display.
Example: At normal mode
Example: At SET mode
* You can control up to 8 components,
each of which are preset at Setting
position numbers “S-1” to “S-8.”
Note
At normal conditions, the LCD display
shows the last selected component
name. When the batteries are low of
charge, “BATT” appears in the display
after you press a control button.
How to use the Jog dial
The Jog dial can be used to
perform various operations at the
setup procedure, as well as
selecting the components to
operate.
Example: At normal mode
1Turn the Jog dial to select the
component you want to
operate.
2Press the button for the desired
function.
Example: At SET mode
1Turn the Jog dial to select the
Setting position number (“S-1”
to “S-8”).
2Press to enter.
The component name flashes in
the display.
Tip
You can also press b/B instead of
turning the Jog dial to the left/right
(except for when you select a character
at the NAME mode).
You can also press OK instead of
pressing the Jog dial.
Current Component
Remote control signal indicator
-1S
¢
ESETPR
VT¢1
Remote control signal indicator
Component Component
code number
Setting mode
Setting position number*
RCV
-1S
ESETPR
VT

8GB
Tip
You can also press b/B instead of
turning the Jog dial to the left/right.
You can also press OK instead of
pressing the Jog dial.
Basic Operations
Setting the
Component Codes
The Commander is preset at the
factory to operate Sony brand AV
components (see the table below).
You can use the Commander with
other preset AV components also.
If you are using the Commander
with a factory-set Sony
component, skip the following
procedures.
To use with other AV components,
you need to follow the procedures
to set the correct codes for each
component.
You can set 8 different
components to 8 Setting position
numbers (S-1 to S-8).
* Analog audio compact cassette deck
Note
See “Table of Preset Functions” (page
38) for the functions of buttons as for
each component.
Setting by entering the
code number
Setting
position
number
S-1
S-2
S-3
S-4
S-5
S-6
S-7
S-8
Factory setting
Sony TV
Sony SAT
Sony VHS
VCR
Sony DVD
player
Sony CD
player
Sony MD deck
Sony cassette
deck
Sony amplifier
Display
TV
SAT
(Satellite tuner)
VCR
(Video player)
DVD
CD
MD
TAPE
(Cassette
deck*)
AMP
(Amplifier)
7
2
Jog
dial

9GB
4Turn the Jog dial to select
the Setting position number
(“S-1” to “S-8”).
Each time you turn the Jog dial,
the display changes as follows.
Notes
• If you have changed the names of
the components (page 26) those
names are displayed.
• If you press the Jog dial at “EXIT,”
the Commander returns to the top
of SET mode (Step 2).
5Press the Jog dial.
The component name flashes
in the display.
Note
The component names displayed at
this point represent the type of the
component to operate. These names
cannot be changed.
If you want to set a different
component to this Setting
position number, turn the Jog
dial to select the desired
component. The display
changes as shown below.
Continued
Example: To set up a Philips’ TV
at “S-1/TV”
1See the tables in the
supplied “Component
Code Numbers,” and find
the three-digit code number
for the desired component.
If more than one code number
is listed, use the number that is
listed first.
For example, to set up a
Philips’ TV, you would use the
code number 086.
2Press SET.
“PRESET” flashes in the
display, and the Commander
changes to SET mode.
3Press the Jog dial.
The Setting position number
flashes, and the component
name appears in the display.
The Commander changes to
the Component PRESET mode.
Note
If you have changed the name of
the component (page 26) that name
is displayed.
ES
TSE
RPET
-1S
ESETPR
VT
EXIT S-8
AMP
S-7
TAPE
S-6
MD
S-1 S-2 S-3
TV SAT VCR
S-4
DVD
S-5
CD
-1S
¢
ESETPR
VT¢1
EXIT AMP TAPE MD
TV SAT VCR DVD CD

10GB
Tips
• You can also press PROGR +/– to
go to the next/previous code
number.
• It is useful that you take a note of
the code number.
8Press the Jog dial.
“OK” appears in the display.
The code number is set, and
the Commander returns to the
Component PRESET mode.
If “NG” flashes twice and the
three-digit component code
number flashes again after you
press the Jog dial, it means that
the setup is incomplete. Check
the component code number,
and try setting again from Step
7.
If you want to set a code for
another component, repeat
from Steps 4 to 8.
9Select “EXIT,” then press
the Jog dial to finish setting.
To cancel setup
Press SET.
Setting the Component Codes
(continued)
Notes
• You cannot set “AMP” at “S-1” to
“S-7.” You can set “AMP” only at
“S-8.”
• If you press the Jog dial at “EXIT,”
the Commander returns to the top
of the Component PRESET mode
(Step 3).
6Press the Jog dial.
The three-digit code number
next to the component name
flashes in the display.
7Press the Number buttons
to enter the three-digit
component code number.
As you press a button, the
number appears from the right
side of the flashing numbers,
and moves to the left when you
press another button.
In this example:
Press 0, 8, 6.
When you set the code
number to “000”
The component set at this Setting
position number does not appear in
the display at normal mode, and
you cannot operate the component.
This is useful when you want to
skip unused components.
To put it back to the display, set the
code number to match your
component.
-1S
¢
ESETPR
VT¢1
-1S
ESETPR
VT
-1S
ESETPR
KO