Sony HT-ZF9 User guide

Startup Guide
Sound Bar : HT-ZF9
4-727-534-32(1)
Continued on back page
© 2018 Sony Corporation Printed in Malaysia
What’s in the box
Bar Speaker (1) Subwoofer (1) Remote control (1)
Grille frame (1) Optical digital cable (1) R03 (size AAA) battery (2)
WALL MOUNT TEMPLATE (1) Wall mounting bracket (2),
Screw (2)
Operating Instructions
Startup Guide (this document)
1Connecting with a TV and other devices
: Video signal
: Audio signal
Blu-ray Disc™ player,
cable box or satellite
box, etc.
: Video signal
: Audio signal
Blu-ray Disc player,
cable box or satellite
box, etc.
YES NO
Are there any HDMI IN jacks labeled “eARC” or “ARC” on your TV?

HDMI OUT
TV eARC/ARC
Use High Speed HDMI Cable with Ethernet (not supplied) to connect an HDMI IN jack on your TV and the HDMI OUT (TV eARC/ARC) jack
on the Bar Speaker.
Note
•Make sure that the cable is firmly inserted.
•When your TV does not have an HDMI IN jack labeled “eARC” or “ARC,” you will also need to connect the TV and the Bar Speaker via the optical digital cable
(supplied) as instructed in step . There will be no sound output from the TV if the TV and the Bar Speaker are connected only via the HDMI cable.
•Do not use a cable which is wide enough to touch the casing of the Bar Speaker. If it is used, the connector area will overload and it may interrupt the
picture or cause malfunction.
•To watch 4K video content, refer to “Connecting a 4K TV and 4K Devices” in the Operating Instructions (separate document).

HDMI IN
1/2
Use an HDMI cable (not supplied) to connect an HDMI OUT jack on a device and either the HDMI IN 1 jack or HDMI IN 2 jack on the Bar
Speaker.
Note
•Make sure that the cable is firmly inserted.
•To watch 4K video content, refer to “Connecting a 4K TV and 4K Devices” in the Operating Instructions (separate document).
Tip
•When devices such as a Blu-ray Disc player, cable box, or satellite box are currently connected to a TV, disconnect the device from the TV and then connect
it to the Bar Speaker to reproduce the high quality surround sound.

TV IN
(OPT)
When your TV does not have an HDMI IN jack labeled “eARC” or “ARC,” use the optical digital cable (supplied) to connect an optical out
jack on your TV and the TV IN (OPT) jack on the Bar Speaker.
Note
•Check the shape of the optical digital cable’s connecters and the jacks on the TV and the Bar Speaker. Insert the connecters into the jacks in the right
directions. If you forcibly insert the connecters in the wrong directions, the connecters and the jacks may be damaged.
Installation position
Subwoofer
Bar Speaker
Note
•Do not place magnetic cards on the system or near the system.
•Do not cover the top of the Bar Speaker with metal objects such as TV frame, etc. Wireless functions may
become unstable.
•Do not place metal objects around the system. Wireless functions may become unstable.
To mount the Bar Speaker on a wall
Refer to “Mounting the Bar Speaker or Rear Speaker (not supplied) on a Wall” in the Operating
Instructions (separate document).
Refer to the Operating Instructions
(separate document) for the TV connection
methods below.
Connecting Sony TV with the BLUETOOTH Function
Wirelessly
Connecting a 4K TV and 4K Devices
Connecting a TV with an Analog Audio Cable
Startup Guide (this document) explains how to connect the Bar Speaker
and a TV via an HDMI cable.

2Setting up the remote control
3Turning on the TV
Power ON
4Turning on the system
 /
Power indicator
(green)


Connect the AC power cords (mains leads) of the Bar Speaker and subwoofer to the AC outlet (mains).
The remote control of the system does not work until “HELLO” in the front panel display on the Bar Speaker disappears.

Press (power) on the remote control of the system.
“TV” appears in the front panel display on the Bar Speaker.

Confirm that the power indicator of the subwoofer is lit in green.
If the power indicator of the subwoofer is lit in green, the connection with the Bar Speaker is complete.
If not, refer to “Subwoofer” of “Troubleshooting” in the Operating Instructions (separate document).
5Listening to sound
TV HDMI2
HDMI1
TV input switch
To listen to the audio of the TV

Select the desired input using the TV remote control.
The screen switches to the television broadcast screen and the TV audio is output from
the system.
If “TV” does not appear in the front panel on the Bar Speaker, press TV on the remote
control of the system to select the TV input. “TV” appears in the front panel display on
the Bar Speaker.
To listen to the audio of a device that is connected to the HDMI IN jack
on the Bar Speaker

Turn on the connected device. Then use the TV remote control to switch the
TV input to that for the HDMI IN jack to which the system is connected.

Press HDMI1 or HDMI2 on the remote control of the system depending on the
HDMI jack to which the device is connected.
“HDMI1” or “HDMI2” appears in the front panel display on the Bar Speaker and the audio
of the connected device is output from the system.
Note
•Depending on the order in which you connect the TV and the system, the system may be muted and “MUTING” may appear on the front panel display on the Bar Speaker. If this happens, turn on the TV first, then
the system.
6Enjoying immersive surround experience
+/–
VERTICAL S.
SW +/–

Press VERTICAL S. on the remote control of the system.
Enjoy movies, music, and more with sound that flows all around the room, surrounding you from all directions.

Adjust the volume.
Adjust the volume of the Bar Speaker by pressing +/− on the remote control of the system.
Adjust the volume of the subwoofer by pressing SW +/− on the remote control of the system.
Note
•The surround effect from all directions differs depending on the sound source.
How to display the operation screen of the system on the TV
Perform Easy Setup to display the system’s menu on the TV.

Press HOME on the remote control of the system.
The Easy Setup screen is displayed on the TV screen.
If the Easy Setup screen does not appear, use the TV remote control to switch the TV input to that for the HDMI IN jack to which the system is connected.

Select the language that you want for the system on-screen display.

Perform settings by following the on-screen instructions.
Troubleshooting
No TV sound is output from the system, or no picture is displayed on the TV.
•Press TV on the remote control of the system to select the TV input. “TV” appears in the front panel display on the Bar Speaker.
•Make sure that the input and output of the HDMI jacks on the system are correct.
•Disconnect the cables that are connected between the TV and the system, then connect them firmly again. Disconnect the AC power cords of the TV and the system from the AC outlets (mains), then connect them again.
•When the TV and the system are connected via an HDMI cable, enable the Control for HDMI function or the eARC/ARC function on the TV. For details on the TV’s settings, refer to the operating instructions supplied with the TV.
For more information about the Control for HDMI function, refer to the Operating Instructions (separate document).
•Check the sound setting of the TV. When the TV is set to output the sound from the TV speakers, change the setting to output the sound from the external speakers.
No picture or sound from the device connected to the system is output.
•Press one of the input buttons (TV, HDMI1, HDMI2, BLUETOOTH or ANALOG) on the remote control of the system to select the desired input. The input type that corresponds with the selected input appears in the front panel
display on the Bar Speaker.
•Make sure that the input and output of the HDMI jacks on the system are correct.
•Disconnect the cables connected to the system, and then connect them again. Make sure that the cables are firmly inserted.
The TV remote control does not work.
•When the Bar Speaker obstructs the remote control sensor of the TV, the TV remote control may not work. In that case, set [IR-Repeater] to [On]. You can control the TV with the TV remote control. For details, refer to “When the
TV Remote Control does not Work” in the Operating Instructions (separate document).
No sound or only a very low-level sound is heard from the subwoofer.
•Press SW + on the remote control of the system to increase the volume of the subwoofer.
•Make sure that the power indicator on the subwoofer is lit in green. If the power indicator does not light up, refer to “Subwoofer” of “Troubleshooting” in the Operating Instructions (separate document).
•The subwoofer is designed for playback of bass or low frequency sounds. When the input source does not contain much bass sound, such as in TV programs, the bass sound from the subwoofer may be difficult to hear. You
can check the subwoofer sound by emitting the test tone. For details, refer to “Customizing the Speaker Settings for Surround Sound” in the Operating Instructions (separate document).
If the problem is not solved even though you have tried the measures above, refer to “Troubleshooting” in the Operating Instructions (separate document).