Sony Mex-n50000bt User manual

I

SONY.

Bluetooth®

Audio

System

Owner's

Record

The model and serial

numbers

are located on

the

bottom

of

the

unit.

Record these

numbers

in

the

spaces provided below.

Refer

to

these

numbers

whenever

you

call

upon

your

Sony dealer

regarding this product.

Model No.

Serial No.

To

cancel

the

demonstration

(DEMO) display, see page

17.

Pour

annuler

l'affichage de

demonstration

(DEMO), reportez-

vous a

Ia

page

19.

cillD~~

DIGITAL

AU

DID

I

TEXT

I

WORKS

WITH

PANDORA

Made for

~

iPod

[OJ

iPhone

MfX

..

NSOOOBT

/MEX-GS610BT

4-480-657-11(1)

Operating Instructions

Mode

d'emploi

Be

sure

to

install this

unit

in

the

dashboard

of

the

car for safety.

For

installation and connections,

see

the

supplied installation/connections manual.

Warning

FOR THE CUSTOMERS IN THE USA. NOT

APPLICABLE IN CANADA, INCLUDING IN

THE

PROVINCE OF QUEBEC.

POUR

LES

CLIENTS AUX ETATS-UNIS. NON

APPLICABLE AU CANADA, Y COMPRIS

LA

PROVINCE

DE

QUEBEC.

This

equipment

has been tested and found

to

comply

with

the

limits for a

Class

Bdigital device,

pursuant to Part

15

of

the

FCC

Rules.

These limits are designed

to

provide reasonable

protection against harmful interference in a

residential installation. This

equipment

generates, uses, and can radiate radio frequency

energy and,

if

not

installed and used

in

accordance

with

the instructions, may cause

harmful interference

to

radio communications.

However, there

is

no guarantee

that

interference

will not occur in a particular installation.

If

this

equipment

does cause harmful interference

to

radio or television reception, which

can

be

determined by

turning

the

equipment

off

and

on,

the

user

is

encouraged

to

try

to

correct the

interference by one or more

of

the

following

measures:

-Reorient or relocate

the

receiving antenna.

-Increase the separation between the

equipment

and receiver.

-Connect

the

equipment

into an outlet on a

circuit different from

that

to

which the receiver

is

connected.

-Consult the dealer or an experienced radio/TV

technician for help.

You

are cautioned

that

any changes or

modifications

not

expressly approved in this

manual could void your

authority

to

operate this

equipment.

This device complies

with

Part

15

of

the

FCC

Rules

and Industry Canada licence-exempt

RSS

standard(s).

Operation

is

subject to

the

following

two

conditions:

(1)

this device may

not

cause harmful

interference, and

(2)

this device

must

accept any

interference received, including interference

that

may cause undesired operation

of

the

device.

This transmitter

must

not

be co-located

or

operated

in conjunction

with

any

other

antenna or

transmitter.

Under Industry Canada regulations, this radio

transmitter may only operate using

an

antenna

of

a

type and

maximum

(or lesser) gain approved for

the transmitter by Industry Canada.

To

reduce

potential radio interference

to

other users, the

antenna type and its gain should be

so

chosen that

the equivalent isotropically radiated

power

(e.i.r.p.)

is

not

more than

that

necessary for successful

communication.

This

equipment

complies

with

FCC/IC

radiation

exposure limits set

forth

for an uncontrolled

environment and meets

the

FCC

radio frequency

(RF)

Exposure Guidelines and

RSS-102

of

the

IC

radio frequency

(RF)

Exposure rules. This

equipment

has very

low

levels

of

RF

energy

that

it

deemed

to

comply

without

maximum permissive

exposure evaluation

(MPE).

But it

is

desirable that it

should be installed and operated keeping

the

radiator at least 20

em

or more away from person's

body (excluding extremities: hands, wrists, feet and

ankles).

CAUTION

The use

of

optical instruments

with

this product will

increase eye hazard.

For

the

State

of

California, USA

only

Perchlorate

Material-

special handling may apply,

See

www.dtsc.ca.gov/hazardouswaste/perchlorate

Perchlorate Material: Lithium battery contains

perchlorate

Note

on

the

lithium

battery

Do

not

expose

the

battery

to

excessive heat such

as

direct sunlight, fire or the like.

Warning

if

your

car's

ignition

has

no

ACC

position

Be

sure

to

set the

AUTO

OFF

function (page

17).

The unit will shut

off

completely and

automatically in the set

time

after the

unit

is

turned off, which prevents battery drain.

If

you

do

not

set

the

AUTO

OFF

function, press and hold

OFF

until

the

display disappears each

time

you

turn

the

ignition

off.

Notes

on

BLUETOOTH

function

Caution

IN

NO

EVENT

SHALL SONY

BE

LIABLE

FOR

ANY

INCIDENTAL,

INDIRECT

OR

CONSEQUENTIAL

DAMAGES

OR

OTHER

DAMAGES INCLUDING,

WITHOUT LIMITATION,

LOSS

OF

PROFITS,

LOSS

OF

REVENUE,

LOSS

OF

DATA,

LOSS

OF

USE

OF

THE

PRODUCT

OR

ANY

ASSOCIATED

EQUIPMENT,

DOWNTIME, AND

PURCHASER'S

TIME

OR

ARISING

OUT

OF

THE

USE

OF

THIS

PRODUCT,

ITS

HARDWARE AND/OR

ITS

SOFTWARE.

IMPORTANT NOTICE!

Safe and efficient use

Changes

or

modifications

to

this

unit

not

expressly

approved

by

Sony

may

void

the

user's

authority

to

operate

the

equipment.

Please check

for

exceptions,

due

to

national

requirement

or

limitations,

in usage

of

BLUETOOTH

equipment

before

using

this

product.

Driving

Check

the

laws and

regulations

on

the

use

of

cellular

phones

and

handsfree

equipment

in

the

areas

where

you

drive.

Always give full

attention

to

driving

and

pull

off

the

road

and

park before

making

or

answering

a call

if

driving

conditions

so require.

Connecting

to

other

devices

When

connecting

to

any

other

device, please read

its user

guide

for

detailed

safety

instructions.

Radio

frequency

exposure

RF

signals

may

affect

improperly

installed

or

inadequately

shielded

electronic

systems in cars,

such

as

electronic

fuel

injection

systems, electronic

antiskid (antilock) braking systems, electronic

speed

control

systems

or

air

bag

systems. For

installation

or

service

of

this

device, please consult

with

the

manufacturer

or

its representative

of

your

car. Faulty installation

or

service

may

be

dangerous

and

may

invalidate any

warranty

that

may

apply

to

this device.

Consult

with

the

manufacturer

of

your

car

to

ensure

that

the

use

of

your

cellular

phone

in

the

car will

not

affect

its electronic system.

Check regularly

that

all wireless device

equipment

in

your

car

is

mounted

and

operating

properly.

Emergency

calls

This

BLUETOOTH

car

handsfree

and

the

electronic

device

connected

to

the

handsfree

operate

using

radio signals, cellular,

and

landline

networks

as

well

as

user-programmed

function,

which

cannot

guarantee

connection

under

all

conditions.

Therefore

do

not

rely solely

upon

any

electronic

device

for

essential

communications

(such

as

medical emergencies).

Remember, in

order

to

make

or

receive calls,

the

handsfree and

the

electronic device

connected

to

the

handsfree

must

be

switched

on in a service area

with

adequate

cellular signal strength.

Emergency calls

may

not

be possible on all cellular

phone

networks

or

when

certain

network

services

and/or

phone

features are in use.

Check

with

your

local service provider.

Table

of

Contents

Warning

...................................

2

Guide

to

Parts

and

Controls

...................

5

Getting Started

Detaching

the

Front Panel

.....

...

............

6

Setting

the

Clock

............................

6

Preparing a

BLUETOOTH

Device

................

7

Connecting an iPod/USB Device .

..............

8

Connecting

Other

Portable

Audio

Device

........

9

Listening to the Radio/SiriusXM

Listening

to

the

Radio

........................

9

Using Radio Data System

(RDS)

...............

10

Listening

to

the

SiriusXM Radio

...............

10

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

Playing an iPod/USB Device

..................

11

Playing a

BLUETOOTH

Device

.................

11

Searching and Playing Tracks

.................

12

Listening to Pandora®

Preparing

for

Pandora®

.......

..

.............

13

Streaming Pandora®

........................

13

Available Operations in

the

Pandora®

..........

13

Handsfree Calling

Receiving a Call

............................

14

Making

a Call .

.............................

14

Available Operations

during

Call

..............

15

Useful Functions

App

Remote

with

iPhone/

Android

Phone

......

15

Settings

Canceling

the

DEMO

Mode

. . . . . . . . . . . . . . . . . .

17

Basic Setting

Operation

. . . . . . . . . . . . . . . . . . . . .

17

GENERAL

Setup

............................

17

SOUND Setup

..............................

17

EQ10

PRESET

. . . . . . . . . . . . . . . . . . . . . . . . . . .

17

EQ10

SETIING . . . . . . . . . . . . . . . . . . . . . . . . . .

17

POSITION {listening

position)

..............

18

RB

ENH

(rear bass enhancer)

..............

18

SW

DIREC

(subwoofer

direct

connection)

....

18

DISPLAY Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

COLOR

(preset

color-

dynamic

color

illuminator)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

CUSTOM-C

(custom

color) . . . . . . . . . . . . . . . .

19

SND

SYNC

(sound

synchronization)

........

19

WHT MENU

{white

menu)

................

19

START-WHT

{start

white)

...

.

.............

19

BT

{BLUETOOTH} Setup

.....................

19

BT

IN

IT

{BLUETOOTH initialize)

.............

19

APP

REM

{App

Remote)

Setup

...............

19

Additional Information

Precautions

...............................

20

Maintenance.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

Troubleshooting

...........................

24

Guide

to

Parts

and

Controls

The

number

3/C:

(repeat) button has a tactile dot.

[I]

Q {browse) {page 12, 13)

Enter the browse mode during playback.

[gJ

Front panel release button

~SEEK+/-

Tune in radio stations automatically.

Press

and

hold to tune manually.

~~~

{prev/next)

.,.../_...

{fast-reverse/fast-forward)

~

Control dial

Rotate

to

adjust

the

volume.

ENTER

Enter the selected item.

Press

SRC,

rotate then press to change the

source.

VOICE

{page 15)

Activate voice dial.

When the App Remote function

is

on, the voice

recognition

is

activated (Android™ phone only).

-APP

Press

and hold for more than 2 seconds

to

establish App Remote function (connection).

N-Mark

Touch the control dial

with

Android phone

to

make

BLUETOOTH

connection.

[ID

Receptor for the remote commander

[§]

Disc

slot

[1]

Display

window

[ID

~{disc

eject)

liD

SRC

{source)

Turn on the power.

Change the source.

-OFF

Press

and hold

for

1second to turn

off

the

power.

Press

and hold for more than 2 seconds to turn

off

the power and the display.

If

the unit

is

turned

off

and the display

disappears,

it

is

unable you to operate with

the

remote.

[Q]

~{back)

Return

to

the previous display.

MODE {page 9,

11,

13, 15)

[j]

CALL~

Enter the call menu. Receive/end a call.

Press

and hold more than 2 seconds

to

switch

the

BLUETOOTH

signal.

[12]

MENU

Open the setup menu.

-DSPL {display)

Press

and hold, then press

to

change display

items.

~

Number

buttons

{1

to 6)

Receive stored radio stations.

Press

and hold

to

store stations.

Call

a stored phone number.

Press

and hold

to

store a phone number.

ALBUM

T/A

Skip

an

album

for

audio device.

Press

and hold

to skip albums continuously.

Press

A

to

thumbs up, or T

to

thumbs

down

in

Pandora®

(page

13).

C:

{repeat)

~{shuffle)

MIC

(page

15)

PAUSE

[H]

PTY

(program

type)

Select

PTY

in

RDS.

CAT

(category)

Select radio channels

in

SiriusXM.

~

AUX

input

jack

[1§1

USB

port

The

VOL

(volume)+

button

has a tactile dot.

Remove the insulation film before use.

[Z]

...

(~

)/

...

(~)

MVOL

(Volume)

+/-

~SOUND

Open the

SOUND

menu directly.

-MENU

Press

and hold

to

open

the

setup menu.

~

t (+)/.J (-)

12}]

DSPL

(display)/-SCRL(scroll}

6GB

Change display items.

Press

and hold

to

scroll a

display item.

Getting

Started

Detaching

the

Front

Panel

You

can

detach

the

front panel

of

this

unit

to

prevent theft.

1 Press and

hold

OFF

G).

The unit

is

turned off.

2 Press

the

front

panel release

button

@,

then

remove

the

panel

by

pulling

it

towards

you.

Caution

alarm

If

you turn the ignition switch

to

the

OFF

position

without

detaching the

front

panel, the caution

alarm will sound

for

a

few

seconds. The alarm will

only sound

if

the built-in amplifier

is

used.

Serial

numbers

Make sure the serial numbers on the

bottom

of

the

unit

and the back

of

the

front

panel are matched

correctly. Otherwise you cannot make

BLUETOOTH

pairing, connection and disconnection by

NFC.

Setting

the

Clock

1 Press MENU, rotate

the

control dial

to

select [GENERAL],

then

press it.

2 Rotate

the

control dial

to

select

[CLOCK-

ADJ],

then

press it.

The

hour

indication flashes.

3 Rotate

the

control dial

to

set

the

hour

and minute.

To

move the digital indication, press SEEK+/-.

4

After

setting

the

minute,

press

MENU.

The setup

is

complete and the clock starts.

To

display

the

clock, press

DSPL.

Preparing

a

BLUETOOTH

Device

You

can enjoy music, or

perform

handsfree calling,

by connecting a suitable

BLUETOOTH

device.

For

details on connecting, refer

to

the operating

instructions supplied

with

the

device.

Before connecting

the

device,

turn

down

the

volume

of

this unit; otherwise, loud sound may

result.

When connecting a

BLUETOOTH

device (cellular

phone, audio device, etc.)

for

the first time, mutual

registration (called

"pairing")

is

required. Pairing

enables this

unit

and

other

devices

to

recognize

each other.

1 Place

the

BLUETOOTH

device

within

1m

{3

ft}

of

this unit.

2 Press

CALL,

rotate

the

control dial

to

select [PAIRING],

then

press it.

0 flashes.

The

unit

enters pairing standby mode.

3 Perform pairing

on

the

BLUETOOTH

device so

it

detects this

unit.

4 Select [Sony Car

Audio]

shown

in

the

display

of

the

BLUETOOTH

device.

If

[Sony

Car

Audio] does

not

appear, repeat from

step

2.

oQ=

DR-BT30Q t

I

Sony

J4i-

Car

Audio

xxxxxxx

5

If

passkey*

input

is required on

the

BLUETOOTH

device,

input

[0000].

*

Passkey

may

be

called

"Passcode,"

"PIN

code,"

"PIN

number" or."Password,"

etc.,

depending

on

the device.

oQ=

I

.....

I

xxxx-

Input

passkey

[0000]

When pairing

is

made, 0 stays lit.

6 Select this

unit

on

the

BLUETOOTH

device

to

establish

the

BLUETOOTH

connection.

~"

or

r]"

lights

up

when

the connection

is

made.

Note

While connecting to a

BLUETOOTH

device, this unit

cannot

be

detected from another device.

To

enable

detection, enter the pairing mode

and

search

for this

unit from another device.

To

cancel

pairing

Perform step 2

to

cancel the pairing

mode

after this

unit

and

the

BLUETOOTH

device are paired.

To

use a paired device, connection

with

this

unit

is

required. Some paired devices will connect

automatically.

))

1 Press

CALL,

rotate

the

control dial

to

select [BT SIGNL],

then

press it.

Make sure

that

0 lights up.

2 Activate

the

BLUETOOTH

function

on

the

BLUETOOTH

device.

3 Operate

the

BLUETOOTH

device

to

connect

to

this unit.

~"

or

r]"

lights up.

Icons in

the

display:

~"

Lights up when a cellular phone

is

connected

to

the unit.

r]"

Lights

up

when an audio device

is

connected

to

the unit.

Indicates the signal strength status

of

T.ll

connected cellular phone.

To

connect

the

last-connected

device

from

this

unit

Activate the

BLUETOOTH

function on

the

BLUETOOTH

device.

Press

SRC.

Select

[BT

PHONE]

or

[BT

AUDIO].

Press

ENTER

to

connect with the cellular phone, or

PAUSE

to

connect

with

the audio device.

Note

While streaming

BLUETOOTH

audio, you cannot

connect from this unit

to

the

cellular phone. Connect

from the cellular phone to this

unit

instead.

Tip

With

BLUETOOTH

signal on: when the ignition

is

turned

to on, this unit reconnects automatically

to

the last-

connected cellular phone.

To

install

the

microphone

For

details on

how

to

connect the microphone, refer

to

the supplied "Installation/Connections" guide.

Confle

;ctingwith a

S

'

m

;

~rtphe

,

ae

by

'O:

ne

tou(b

'(;

NFC)

'

By

touching the control dial on

the

unit

with

an

NFC*

compatible smartphone,

the

unit

is

paired and

connected

with

the smartphone automatically.

*

NFC

(Near Field Communication)

is

a technology

enabling short-range wireless communication

between various devices, such

as

mobile phones and

IC

tags. Thanks to the

NFC

function, data

communication

can

be achieved easily

just

by

touching the relevant symbol or designated location

on

NFC

compatible devices.

For

a smartphone

with

Android

OS

4.0 or lower

installed,

downloading

the

app

"NFC

Easy

Connect"

available at Google

Play™

is

required. The app may

not be downloadable in some countries/regions.

1

Activate

the

NFC

function

on

the

smartphone.

For

details, refer

to

the

operating instructions

supplied

with

the smartphone.

2 Touch

the

N-Mark

part

of

the

unit

with

theN-Mark

part

of

the

smartphone.

Make sure

that

0 lights

up

on the display

of

the

unit.

To

disconnect

by

One

touch

Touch

the

N-Mark part

of

the

unit

with

the N-Mark

part

of

the

smartphone again.

Notes

• When making

the

connection, handle

the

smartphone carefully to prevent scratches.

• One touch connection

is

not

possible when the

unit

is

already connected

to

another

NFC

compatible device.

In

this case, disconnect the other device, and make

connection with the smartphone again.

C9J'l:ne~i~Q

•''

"it~~

/

fl

,,,,

i

,

p~~Jl~/i

'

RQft

(BtU

,

EI:OO'fH

Auto

Pairing}

When an iPhone/iPod

with

iOSS

or later installed

is

connected

to

the

USB

port, the

unit

is

paired and

connected

with

the iPhone/iPod automatically.

To

enable

BLUETOOTH

Auto Pairing, make sure

[AUTO

PAIRING]

in

BT

setup

is

set to [ON] {page

19).

1

Activate

the

BLUETOOTH

function on

the

i

Phone/i

Pod.

2 Connect an iPhone/iPod

to

the

USB

port.

Make sure

that

0 lights up on the display

of

the

unit.

Note

BLUETOOTH

Auto Pairing

is

not possible

if

the unit

is

already connected

to

another

BLUETOOTH

device.

In

this

case,

disconnect the other device, then connect the

iPhone/iPod again.

Connecting

an

iPod/USB

Device

1

Turn

down

the

volume

on

the

unit.

2 Connect

the

iPod/USB device

to

the

unit.

To

connect an iPod/iPhone, use the

USB

connection cable for iPod (not supplied).

When connecting iPhone 5

For

MEX-GS610BT,

the

rear

USB

port

is

also

available.

Connecting

.

Other

Portable

Audio

Device

1 Turn

off

the

portable

audio device.

2 Turn

down

the

volume

on

the

unit.

3 Connect

the

portable

audio device

to

the

AUX

input

jack (stereo

mini

jack) on

the

unit

with

a connecting cord (not

supplied)*.

*

Be

sure

to

use a straight type plug.

4 Press

SRC

to

select [AUX).

To

match

the

volume

level

of

the

connected

device

to

other

sources

Start playback

of

the

portable audio device at a

moderate volume, and set your usual listening

volume on

the

unit.

Press

MENU

and rotate

the

control dial.

Select

[SOUND]~

[AUX VOL] (page

19).

Listening

to

the

Radio/SiriusXM

Listening

to

the

Radio

To

listen

to

the

radio, press

SRC

to

select

[TUNER].

1

Press

MODE

to

change

the

band

(FM1,

FM2,

FM3,

AM1

or

AM2).

2

Press

MENU,

rotate

the

control dial

to

select

[GENERAL],

then press it.

3 Rotate

the

control dial

to

select [BTM],

then

press it.

The

unit

stores stations in order

of

frequency on

the

number

buttons.

1

Press

MODE

to

change

the

band

(FM1,

FM2,

FM3,

AM1

or

AM2).

2 Perform

tuning.

To

tune

manually

Press

and hold SEEK+/-

to

locate the

approximate frequency, then press SEEK+/-

repeatedly

to

fine adjust

to

the desired

frequency.

To

tune

automatically

Press

SEEK+/-.

Scanning stops when

the

unit receives a station.

Repeat this procedure until the desired station

is

received.

1 While receiving

the

station

that

you

want

to

store, press and hold a

number

button

(1

to

6)

until

[MEM] appears.

1 Select

the

band, then press a

number

button

(1

to

6).

Using

Radio

Data

System

(RDS)

Use

PTY

to display

or

search

for

a desired program

type.

1

Press

PTY

during

FM

reception.

2 Rotate

the

control dial

until

the

desired

program

type

appears,

then

press it.

The

unit

starts

to

search

for

a station

broadcasting

the

selected program type.

Type

of

programs

NEWS

{News), INFORM {Information),

SPORTS

{Sports), TALK {Talk),

ROCK

{Rock),

CLS

ROCK

{Classic Rock),

ADLT

HIT {Adult Hits),

SOFT

RCK

{Soft

Rock),

TOP

40

{Top 40), COUNTRY (Country),

OLDIES

(Oldies),

SOFT

(Soft), NOSTALGA

{Nostalgia), JAZZ

(Jazz),

CLASSICL

(Classical),

RAND

B {Rhythm and Blues),

SOFT

R B (Soft

Rhythm and Blues), LANGUAGE (Foreign

Language),

REL

MUSC

(Religious Music),

REL

TALK

(Religious Talk),

PERSNLTY

(Personality),

PUBLIC

(Public),

COLLEGE

(College),

WEATHER

(Weather)

The

CT

data

from

the

RDS

transmission sets

the

clock.

1

Set [CT-ON] in

GENERAL

setup (page

17).

Listening

to

the

SiriusXM

Radio

To

listen

to

the SiriusXM, press

SRC

to

select

[SIRIUSXM].

Everything

worth

listening

to

is

on SiriusXM,

getting

over 130 channels, including

the

most

commercial-

free music, plus the best sports, news, talk and

entertainment. A SiriusXM Vehicle Tuner (sold

separately) and Subscription are required.

For

more

information, visit

www.siriusxm.com

To

listen

to

SiriusXM Satellite Radio, a subscription

is

required. Activate the SiriusXM Vehicle Tuner

using one

of

the

two

methods

below:

• Online: Go

to

www.siriusxm.com/activatenow

• Phone: Call1-866-635-2349

10GB

For

SiriusXM activation,

the

Radio

ID

is

required.

To

display

the

SiriusXM Radio

10

1

During playback, press

Q

(browse)

to

enter

the

browse

mode.

2 Rotate

the

control dial

to

select

the

channel (0],

then

press it.

seterti

'

fl9tfiafi

,

fl~lsfor

;

si

,

"ft.tsXM

1 Press Q (browse).

2 Rotate

the

control dial

to

select

the

desired channel,

then

press it.

To

select channels

from

categories

1

Press

CAT.

2

Rotate

the

control dial

to

select

the

desired

category,

then

press it.

To

store channels

1

While receiving

the

channel

that

you

want

to

store,

press and hold a

number

button

(1

to

6)

until

[MEM]

appears.

To

receive

the

stored channel, press

MODE

to

select

[SX1],

[SX2]

or

[SX3],

then

press a

number

button

{1

to

6).

To

set a

parental

control

Some SiriusXM channels contain content

that

is

not

suitable

for

children.

You

can enable a parental

control passcode

for

these channels.

1

Press

MENU

and

rotate

the

control dial.

2 Select

[GENERAL]~

[PARENTAL]~

(LOCK

SEL]

~

[LOCK-ON].

3

Enter

the

passcode,

then

press

ENTER.

The initial passcode

is

[0000].

To

unlock

the

channels, select

[OFF].

To

change

the

passcode

1

Press

MENU

and

rotate

the

control dial.

2 Select

(GENERAL]~

[PARENTAL]~

[CODE

EDIT]

.

3

Enter

the

current passcode on

the

current passcode

input

display,

then

press

ENTER.

The initial passcode

is

[0000].

4

Enter

your

new

4-digit

passcode on

the

new

passcode

input

display,

then

press

ENTER.

To

change

display

items

Press

and hold,

then

press

DSPL

to

change

as

follows:

Channel

Number

(Default)~

Channel

Name~

Artist

Name~

Song

Title~

Content

Info~

Category Name

~Clock

Playback

Playing

a

Disc

1 Insert

the

disc {label side up).

Playback starts automatically.

Playing

an

iPod/USB

Device

In

these Operating Instructions, "iPod"

is

used

as

a

general reference

for

the

iPod functions on an iPod

and iPhone, unless

otherwise

specified by

the

text

or illustrations.

For

details on

the

compatibility

of

your

iPod, see

"About iPod" (page 20)

or

visit

the

support

site on

the

back cover.

MSC

(Mass Storage Class)-type

USB

devices (such

as

a

USB

flash drive, digital media player, Android

phone)

compliant

with

the

USB

standard can be

used.

Depending on

the

digital

media

player

or

Android

phone, setting

the

USB

connection

mode

to

MSC

is

required.

Notes

•

For

details

on

the compatibility

of

your

USB

device,

visit the support site

on

the back

cover.

• Playback

of

the following MP3/WMA/WAV files

is

not

supported.

-

lossless

compression files

-copyright-protected files

-

DRM

(Digital Rights Management) files

-Multi-channel audio files

1 Connect an iPod/USB device

to

the

USB

port

{page 8).

Playback starts.

If

a device

is

already connected,

to

start

playback, press

SRC

to

select [USB] ([IPD]

appears in

the

display

when

the

iPod

is

recognized).

For

MEX-GS610BT,

press

SRC

to

select

[USB1]

for

the

USB

port

on

the

front, [USB2]

for

the

USB

port

on

the

rear.

2

Adjust

the

volume

on

this unit.

To

stop

playback

Press

and hold

OFF

for

1second.

To

remove

the

device

Stop playback,

then

remove

the

device.

Caution

for

iPhone

When you connect an iPhone via

USB,

phone

call

volume

is

controlled by

the

iPhone,

not

the

unit.

Do

not

inadvertently

increase

the

volume

on

the

unit

during

a call,

as

sudden loud sound may result

when

the

call ends.

Press

and

hold

MODE

during

playback until [MODE

I

POD]

appears

to

enable operation by

the

iPod

directly.

Note

that

the

volume

can be adjusted

only

by

the

unit.

To

exit

passenger control

Press

and hold

MODE

until [MODE AUDIO] appears.

Playing

a

BLUETOOTH

Device

You

can play contents on a connected device

that

supports

BLUETOOTH

A2DP (Advanced Audio

Distribution Profile).

1 Make

BLUETOOTH

connection

with

the

audio

device {page

7).

2

Press

SRC

to

select

[BT

AUDIO].

3 Operate

the

audio

device

to

start

playback.

4

Adjust

the

volume

on this unit.

Notes

• Depending

on

the audio device, information

such

as

title, track number/time

and

playback status may not

be

displayed

on

this unit.

•

Even

if

the source

is

changed

on

this unit, playback

of

the audio device does not stop.

•

[BT

AUDIO]

does not appear

in

the display while

running the

"App

Remote" application

via

the

BLUETOOTH

function.

To

match

the

volume

level

of

the

BLUETOOTH

device

to

other

sources

Start playback

of

the

BLUETOOTH

audio

device at a

moderate volume,

and

set

your

usual listening

volume

on

the

unit.

Press

MENU

and rotate the control dial.

Select [SOUND]-+

[BTA

VOL]

(page 19).

Searching

and

Playing

Tracks

Repe

,

at

••

Pf

,

ay

'

aricl

,

:

stiuM~

,,

,

ptay

1 During playback, press

C:

(repeat)

for

Repeat play,

or

~

(shuffle)

for

Shuffle

play.

2

Press

C:

(repeat)

or

~

(shuffle)

repeatedly

to

select

the

desired play

mode.

Playback in selected play

mode

may take

time

to

start.

Available play modes differ depending on the

selected sound source.

1 During

CD,

USB

or

BT

audio device*1

playback, press Q (browse)*2

to

display

the

list

of

search categories.

When

the

track list appears, press

~

(back)

repeatedly

to

display

the

desired search

category.

*1

Available only for audio devices supporting

AVRCP

(Audio Video Remote Control Profile}

1.4

or above.

*2

During

USB

playback, press

Q

{browse) for

more than 2 seconds

to

directly return to the

beginning

of

the category list.

2

Rotate

the

control dial

to

select

the

desired search category,

then

press

it

to

confirm.

3

Repeat step

2

to

search

the

desired track.

Playback starts.

To

exit

the

Quick-BrowZer

mode

Press

Q (browse).

1

Press

Q (browse).

2

Press

SEEK+.

3

Rotate

the

control dial

to

select

the

item.

The list

is

jumped

in steps

of

10%

of

the

total

number

of

items.

12GB

4 Press

ENTER

to

return

to

the

Quick-

BrowZer mode.

The selected item appears.

5 Rotate

the

control dial

to

select

the

desired item,

then

press it.

Playback starts.

Listening

to

Pandora®

is

available

to

stream music

through

your

iPhone, Android™ and BlackBerry® phones.

You

can

control Pandora® on a USB-connected iPhone or

BLUETOOTH

connected Android/BlackBerry phone

from this unit.

The Pandora® service

is

not

available in some

countries/regions.

Preparing

for

Pandora®

1

To

check

for

compatible devices, visit

the

support

site on

the

back cover.

2 Download

the

latest version

of

the

Pandora® application

from

www.pandora.com

For

Android

phone

only

You

cannot control Pandora® via

the

BLUETOOTH

function while running

the

"App Remote"

application via

BLUETOOTH.

Streaming

Pandora®

1 Connect this

unit

with

the

mobile

device.

• iPhone via

USB

(page 8}

• Android/BlackBerry

phone

via

BLUETOOTH

function (page

7}

2

Press

SRC

to

select [PANDORA

USB]

or

[BT

PANDORA].

3 Launch Pandora® application on

the

mobile

device.

4

Press

PAUSE

to

start playback.

If

the

device

number

appears

Make sure

that

the same numbers are displayed

(e.g., 123456} in this

unit

and

the

mobile

device,

then press

ENTER

on this

unit

and select [Yes] on

the

mobile

device.

When activating

the

BLUETOOTH

function

You

can adjust

the

volume

level.

Press

MENU

and rotate

the

control dial. Select

[SOUND]-+

[BTA

VOL] (page

19}.

Available

Operations

in

the

Pandora®

"Thumbs Up" or "Thumbs Down" feedback allows

you

to

personalize stations.

Thumbs Up

During playback, press

•·

Thumbs

Down

During playback, press

T.

The station list allows you

to

easily select a desired

station.

1 During playback, press Q (browse).

2

Press

SEEK

+

to

select

the

sorting order

[BY

DATE]

or

[A

TO

Z].

3 Rotate

the

control dial

to

select

the

desired station, then press it.

Playback starts.

The track or artist currently being played can be

bookmarked and stored in

your

Pandora® account.

1 During playback, press and

hold

MODE

until

[BOOKMARK] appears.

2 Rotate

the

control dial

to

select

[TRK]

(track)

or

[ART] (artist),

then

press it.

13GB

Handsfree

Calling

To

use a cellular phone, connect

it

with this unit.

For

details,

see

"Preparing a

BLUETOOTH

Device"

(page

7).

~

Receiving

a

Call

1

Press

CALL

when

a call

is

received

with

a

ringtone.

The phone call starts.

Note

The ringtone and talker's voice

are

output

only from the

front speakers.

To

reject

the

call

Press

and hold

OFF

for

1second.

To

end

the

call

Press

CALL

again.

Making

a

Call

You

can

make a call from

the

phonebook or call

history when a cellular phone supporting

PBAP

{Phone Book

Access

Profile)

is

connected.

1

Press

CALL,

rotate

the

control dial

to

select [PHONEBOOK],

then

press it.

2

Rotate

the

control dial

to

select an initial

from

the

initial list,

then

press it.

3

Rotate

the

control dial

to

select a name

from

the

name list,

then

press it.

4

Rotate

the

control dial

to

select a

number

from

the

number

list,

then

press

it.

The

phone call starts.

1

Press

CALL,

rotate

the

control dial

to

select

[RECENT

CALL],

then

press it.

A list

of

the

call history appears.

14GB

2 Rotate

the

control dial

to

select a name

or

phone

number

from

the

call history,

then

press it.

The phone call starts.

Cit

,

1 Press

CALL,

rotate

the

control dial

to

select [DIAL NUMBER],

then

press it.

2

Rotate

the

control dial

to

enter

the

phone

number, and lastly select [ ]

(space),

then

press

ENTER*.

The phone call starts.

*

To

move the digital indication, press SEEK+/-.

Note

[_]appears instead

of[#]

on the display.

1

Press

CALL,

rotate

the

control dial

to

select [REDIAL],

then

press it.

The phone call starts.

You

can

store

up

to 6 contacts in the preset dial.

1

Select a

phone

number

that

you

want

to

store in

the

preset dial, from

the

phonebook,

call

history

or

by

inputting

the

phone

number

directly.

The phone number appears

in

the display

of

this unit.

2

Press and hold a

number

button

(1

to

6}

until

[MEM] appears.

The contact

is

stored in the selected preset

number.

1

Press

SRC,

rotate

the

control dial

to

select

[BT

PHONE],

then

press it.

2

Press a

number

button

(1

to

6)

to

select

the

contact

you

want

to

call.

3

Press

ENTER.

The phone call starts.

You

can make a call

by

saying

the

voice tag stored

in a connected cellular

phone

that

has a voice

dialing function.

1

Press

CALL,

rotate

the

control dial

to

select

[VOICE

DIAL],

then

press it.

Alternatively, press

ENTER

while

the

App

Remote

function

is

off.

2

Say

the

voice

tag

stored on

the

cellular

phone.

Your voice

is

recognized, and

the

call

is

made.

To

cancel voice

dialing

Press

ENTER.

Available

Operations

during

Call

To

preset

the

volume

of

the

ringtone

and

talker's voice

You can preset

the

volume

level

of

the

ringtone

and

talker's voice.

Adjusting

the

ringtone

volume:

Rotate

the

control dial

while

receiving a call.

Adjusting

the

talker's

voice

volume:

Rotate

the

control dial

during

a call.

To

adjust

the

volume

for

the

other

party

(Mic

gain

adjustment)

Press

MIC.

Adjustable

volume

levels: [MIC-LOW], [MIC-MID],

[MIC-Hl].

To

reduce echo

and

noise

(Echo Canceler/

Noise Canceler

Mode)

Press and

hold

MIC.

Settable

mode:

[EC/NC-1], [EC/NC-2].

To

transfer a call

In

order

to

activate/deactivate

the

appropriate

device (this

unit/cellular

phone), press

MODE

or

use

your

cellular phone.

Note

Depending

on

the cellular phone, handsfree connection

may

be

cut

off

when

call

transfer

is

attempted.

To

check

the

status

of

SMS/email*

Ia

flashes

when

a

new

SMS/email

is

received, and

stays lit

when

there are unread messages.

* Available only for a cellular phone supporting

MAP

(Message

Access

Profile).

Useful

Functions

App

Remote

with

iPhone/

Android

Phone

Downloading

the

"App Remote"

application

is

required

from

App

Store

for

iPhone

or

from

Google

Play

for

Android

phone.

Using

the

"App Remote"

application,

the

following

features are available:

-Operate

the

unit

to

launch and control

compatible

applications on

iPhone/

Android

phone.

-Operate

iPhone/

Android

phone

with

simple

finger

gestures

to

control

the

source

of

the

unit.

-Launch an

application/audio

source

or

search

the

keyword on

the

application by saying a

word

or

phrase

into

the

microphone

(Android

phone

only).

-Read

out

incoming

text

messages,

SMS,

email,

Twitter, Facebook, Calendar, etc., automatically,

and

the

text

messages,

SMS

and email can be

replied (Android

phone

only).

-Adjust

the

sound settings

(EQ10,

Balance/Fader,

Listening Position)

of

the

unit

via

iPhone/

Android

phone.

Notes

•

For

your safety, follow your local traffic laws

and

regulations, and do not operate the application while

driving.

• Available operations differ depending

on

the

applications.

For

details on available applications,

visit the support site

on

the back

cover.

• App Remote

ver.

2.0

via

USB

is

compatible with

iOS

5/

iOS

6 installed iPhones.

• App Remote

ver.

2.0

via

BLUETOOTH

is

compatible

with Android devices with Android

2.2, 2.3,

3.*,

4.0,

4.1

or

4.2

installed.

• Voice recognition function does not work depending

on

your smartphone.

In

that

case,

go to [Settings]-

select [Voice Recognition].

• SMS/E-maii/Notification reading

is

available for

Android devices with TIS engine installed.

•

The

"Smart Connect" application, provided by

Sony

Mobile Communications,

is

necessary for Twitter/

Facebook/Calendar, etc., notification

read

out.

15GB

Establishing

the

App

Remote

connection

1

Connect iPhone

to

the

USB

port

or

Android

phone

with

the

BLUETOOTH

function.

2

Launch

the

"App Remote" application.

3 Press and

hold

APP

on

the

unit

for

more

than

2 seconds.

Connection

to

iPhone/

Android

phone

starts.

For details on

the

operations

on

iPhone/

Android

phone, see

the

help

of

the

application.

If

the

device

number

appears

Make sure

that

the

same

numbers

are

displayed

(e.g., 123456) in

this

unit

and

the

mobile

device,

then

press

ENTER

on

this

unit

and

select [Yes] on

the

mobile

device.

To

terminate

connection

Press and

hold

APP.

Selecting

the

source

or

application

You can

operate

the

unit

to

select

the

desired

source or

application

on

your

smartphone.

1 Rotate

the

control dial

to

select

the

desired source

or

application,

then

press it.

•

t··

;0

,,;1

-

1:00

~·;

II

0

l'l.

<zi.•

~

TUNER

CD

USB

~~

(J~

•

AUX

BT

Phone

MUSIC

To

select another source or application, press

SRC

then rotate the control dial to select the desired

source or application.

Announcement

of

various

information

by

voice

guide (Android

phone

only)

When

SMS/E-mail,

Twitter/Facebook/Calendar

notifications,

etc., are received,

they

are

automatically

announced

through

the

car speakers.

•

;

..

"'

.ti'i

-

oj;

• 0

6.

~

;.§

TUNER

1234567890123

USB

•

N!·\·V

~.1essagt>

•

-~

~,~·

AUX

BT

Phone

MUSIC

For

details

on

settings, refer

to

the help

of

the

application.

16GB

Activating

voice

recognition (Android

phone

only)

By

registering

applications,

you

can

control

an

application

by

voice

command.

For details, refer

to

the

help

of

the

application.

To

activate

voice

recognition

1

Press

ENTER

to

activate voice recognition.

2

Say

the

desired voice

command

into

the

microphone

when

[Say Source

or

App]

appears

on

the

Android

phone.

Notes

• Voice recognition may not

be

available in some

cases.

• Voice recognition may not work properly depending

on the performance

of

the connected Android phone.

• Operate under conditions where noise such

as

engine

sound

is

minimized during voice recognition.

When

a

music

or

video

application

is

selected*

Press 1

or

2

to

enter

HID

mode,

and press

SEEK+/-

to

select a playback

item,

then

press

ENTER

to

start

playback.

*

Available only for

an

Android phone supporting

HID

(Human Interface Device Profile).

Making

sound

settings

You can

adjust

the

settings

for

EQ,

BAL/FAD/SW

Level

and

Position via

your

smartphone.

For

details on settings, refer to the help

of

the

application.

Settings

Canceling

the

DEMO

Mode

You

can cancel

the

demonstration

display which

appears

while

this

unit

is

turned

off.

1

Press

MENU,

rotate

the

control dial

to

select [DISPLAY],

then

press it.

2 Rotate

the

control dial

to

select [DEMO],

then

press it.

3 Rotate

the

control dial

to

select [DEMO-

OFF],

then

press it.

The setting

is

complete.

4

Press

~ (back) twice.

The display returns

to

normal

reception/play

mode.

Basic

Setting

Operation

You can set items in

the

menu

to

the

following

procedure.

The

following

items can be set

depending

on

the

source and setting.

1

Press

MENU.

2 Rotate

the

control dial

to

select

the

setup

category,

then

press it.

Setup categories are follows:

•

GENERAL

setup (page

17)

•

SOUND

setup (page

17)

•

DISPLAY

setup (page 19)

•

BT

(BLUETOOTH)

setup

(page 19)

•

APP

REM

(App Remote) setup (page

19)

3 Rotate

the

control dial

to

select

the

options,

then

press it.

To

return

to

the

Press

~

(back).

GENERAL

Setup

CLOCK-ADJ (clock adjust)

(page

6)

CAUT

ALM

(caution alarm)

Activates

the

caution alarm: [ON],

[OFF]

(page 6

).

(Available

only

when

the

unit

is

turned

off.)

BEEP

Activates

the

beep sound: [ON], [OFF].

AUTO OFF

Shuts

off

automatically after a desired

time

when

the

unit

is

turned

off: [NO], [30S] (30

seconds), [30M] (30 minutes), [60M] (60

minutes).

AUX-A

(AUX audio)

Activates

the

AUX source display: [ON],

[OFF].

(Available only

when

the

unit

is

turned off.)

CT

(clock

time)

Activates

the

CT

function:

[ON],

[OFF]

(page 10).

BTM (page 9)

PARENTAL

Sets

the

parental lock

to

[ON],

[OFF],

and edits

the

passcode (page 10). (Available only

when

the

SiriusXM Vehicle Tuner

is

connected.)

SXM

RESET

(SiriusXM reset)

Initializes

the

SiriusXM Connect Tuner settings

(preset channels/parental lock): [ON],

[OFF].

(Available

only

when

the

SiriusXM Vehicle Tuner

is

connected).

SOUND

Setup

C.AUDIO+

(clear audio+)

Reproduces sound by

optimizing

the

digital

signal

with

the

Sony recommended sound

settings: [ON],

[OFF].

(Automatically sets

to

[OFF]

when

[EQ10

PRESET]

is

changed).

EQ10 PRESET

Selects an equalizer curve from

10

equalizer

curves

or

off: [RAND

B],

[ROCK],

[POP], [DANCE],

[HIP-HOP],

[ELECTRONICA],

[JAZZ], [SOUL],

[COUNTRY], [CUSTOM],

[OFF].

The equalizer curve setting can be memorized

for

each source.

EQ10 SETTING

Sets [CUSTOM]

of

EQ10.

BASE

Selects a preset equalizer curve

as

a basis

for

further

customizing: [BAND1] 32Hz, [BAND2]

63

Hz,

[BAND3] 125Hz, [BAND4]

250Hz,

[BANDS]

500Hz,

[BAND6] 1kHz, [BAND7]

2kHz,

[BANDS]

4kHz,

[BAND9] 8 kHz, [BAND10] 16kHz.

The

volume

level

is

adjustable in 1

dB

steps,

from

-6

dB

to

+6 dB.

17GB

POSITION (listening position)

SET

FIR

POS

(set

front/rear

position)

Simulates a natural sound field

by

delaying the

sound

output

from

front/rear

speaker

to

suit

your position.

FRONT

L

(0):

Front

left

FRONT

R

(f)):

Front right

FRONT

(E)):

Center

front

ALL

(0):

In

the center

of

your car

CUSTOM: Position set by App Remote

OFF:

No position set

ADJ

POSITION* (adjust position)

Fine-tunes

the

listening position setting.

Adjustable range:

[+3]-

[CENTER]- [-3].

SET

SW

POS*

(set

subwoofer

position)

NEAR(@): Near

NORMAL(@): Normal

FAR(@):

Far

BALANCE

Adjusts

the

sound balance: [RIGHT-15]-

[CENTER)-

[LEFT-15].

FADER

Adjusts the relative level: [FRONT-15]-

[CENTER]

-

[REAR-15].

OSEE

(digital sound enhancement engine)

Improves digitally compressed sound

by

restoring high frequencies lost in

the

compression process.

This setting can be memorized

for

each source

other than

the

tuner.

Selects the

OSEE

mode: [ON],

[OFF].

LOUDNESS

Reinforces bass and treble for clear sound at

low

volume levels: [ON],

[OFF].

AAV (advanced auto volume)

Adjust

the

playback

volume

level

of

all playback

sources

to

the

optimum

level: [ON],

[OFF].

18GB

RB

ENH

(rear bass enhancer)

Rear

Bass

Enhancer enhances the bass sound

by

applying a

low

pass filter setting

to

the rear

speakers. This function allows

the

rear speakers

to

work

as

a

subwoofer

if

one

is

not

connected.

(Available only when

[SW

DIREC]

is

set

to

[OFF].)

RBE

MODE (rear bass enhancer mode)

Selects

the

rear bass enhancer mode:

[1],

[2], [3],

[OFF].

LPF

FREQ

(low

pass filter frequency)

Selects

the

subwoofer

cut-off

frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF

SLOP

(low

pass filter slope)

Selects

the

LPF

slope:

[1],

[2],

[3).

SW

DIREC

(subwoofer direct connection)

You

can use

the

subwoofer

without

a

power

amplifier when

it

is

connected

to

the

rear

speaker cord. (Available only when

[RBE

MODE]

is

set

to

[OFF].)

Be

sure

to

connect a 4 - 8 ohm

subwoofer

to

either

of

the rear speaker cords.

Do

not

connect

a speaker

to

the

other

rear speaker cord.

SW

MODE (subwoofer mode)

Selects

the

subwoofer mode:

[1],

[2], [3],

[OFF].

SW

PHASE

(subwoofer phase)

Selects

the

subwoofer phase: [NORM],

[REV].

SW

POS*

(subwoofer position)

Selects

the

subwoofer position:

[NEAR],

[NORMAL],

[FAR].

LPF

FREQ

{low pass filter frequency)

Selects

the

subwoofer

cut-off

frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF

SLOP

(low pass filter slope)

Selects

the

LPF

slope:

[1],

[2], [3].

S.WOOFER

(subwoofer)

SW

LEVEL

(subwoofer level}

Adjusts

the

subwoofer volume level:

[+10

dB]-

[0

dB]-

[-10 dB].

([ATI]

is

displayed at

the

lowest setting.)

SW

PHASE

(subwoofer phase)

Selects

the

subwoofer

phase: [NORM],

[REV].

SW

POS*

(subwoofer position)

Selects

the

subwoofer position:

[NEAR],

[NORMAL],

[FAR].

LPF

FREQ

(low

pass filter frequency)

Selects

the

subwoofer

cut-off

frequency: [50Hz],

[60Hz], [80Hz], [100Hz], [120Hz].

LPF

SLOP

(low

pass filter slope)

Selects

the

LPF

slope:

[1],

[2], [3].

HPF

(high pass filter)

HPF

FREQ

(high pass filter frequency)

Selects the

front/rear

speaker

cut-off

frequency:

[OFF],

[50Hz], [60Hz], [80Hz], [100Hz], [120Hz].

HPF

SLOP

(high pass filter slope)

Selects

the

HPF

slope (effective only when

[HPF

FREQ]

is

set

to

other than

[OFF]):

[1],

[2], [3].

AUX VOL

{AUX

volume level)

Adjusts the volume level for each connected

auxiliary device:

[+18

dB]-

[O

dB]-

[-8 dB].

This setting negates the need

to

adjust the

volume level between sources.

BTA

VOL

{BLUETOOTH

audio volume level)

Adjusts the volume level

for

each connected

BLUETOOTH

device: [+6

dB]-

[0

dB]-

[-6 dB].

This setting negates the need

to

adjust the

volume level between sources.

* Does

not

appear

when

[SET

F/R

POS]

is set

to

[OFF].

DISPLAY

Setup

DEMO (demonstration)

Activates the demonstration: [ON],

[OFF].

DIMMER

Changes the display brightness.

AT

(auto)

Dims

the

display automatically

when

you turn

lights on. (Available only when the illumination

control lead

is

connected.)

ON

Dims the display.

OFF

Deactivates the dimmer.

COLOR

(preset color -dynamic color illuminator)

Sets

a preset color

for

the display and buttons

on the main unit.

Selects from

12

preset colors, 1 customized color

and 5 preset patterns.

CUSTOM-( (custom color)

Registers a customized color

for

the

display and

buttons.

BASE

Selects a preset color

as

a basis

for

further

customizing:

[RGB

RED],

[RGB

GRN],

[RGB

BLUE].

Adjustable color range: [O]- [32]

([O]

cannot be

set for all color ranges).

DAYNIGHT

Sets

a different color

for

DAY

/NIGHT mode

according

to

the

dimmer

setting.

-[DAY]:

[DIMMER] sets

to

[OFF]

or

[AUTO] (turn

off

the head light).

-[NIGHT]:

[DIMMER] sets

to

[ON] or[AUTO] (turn

on the head light).

SND

SYNC

(sound synchronization)

Selects the color

with

sound synchronization:

[ON],

[OFF].

WHT MENU (white menu)

You

can display

the

menu more clearly (white)

without

concern

for

color setting: [ON],

[OFF].

START-WHT

(start white)

When

SRC

is

pressed, the display and buttons on

the

main

unit

turn

white

once, then change

to

the customized color: [ON],

[OFF].

AUTO

SCR

(auto scroll)

Scrolls long items automatically: [ON],

[OFF].

BT

(BLUETOOTH)

Setup

This setup menu can be also opened by pressing

CALL.

PAIRING (page

7)

PHONEBOOK (page 14)

REDIAL (page 14)

RECENT

CALL (page 14)

VOICE

DIAL (page

15)

DIAL NUMBER (page 14)

RINGTONE

Selects

whether

this

unit

or the connected

cellular phone outputs the ringtone:

[1]

(this

unit),

[2]

(cellular phone).

AUTO ANS (auto answer)

Sets this

unit

to

answer an incoming call

automatically:

[OFF],

[1]

(about 3seconds),

[2]

(about 10 seconds).

AUTO PAIRING

Start

BLUETOOTH

pairing automatically when

iOS

device version 5.0 or later

is

connected via

USB:

[ON],

[OFF].

BT

SIGNL

(BLUETOOTH

signal) (page

7)

Activates the

BLUETOOTH

function: [ON],

[OFF].

BT

INIT

{BLUETOOTH

initialize)

Initializes all the

BLUETOOTH

related settings

(pairing information, preset number, device

information, etc.).

When disposing the unit, initialize all the

settings.

APP

REM

(App

Remote)

Setup

Establish and terminate App Remote function

(connection).

19GB

Additional

Information

Precautions

•

Cool

off

the unit beforehand

if

your car has been

parked

in

direct sunlight.

•

Do

not leave the front panel or audio devices

brought in inside the

car,

or

it

may cause

malfunction due

to

high temperature

in

direct

sunlight.

• Power antenna (aerial) extends automatically.

Moisture condensation

Should moisture condensation occur inside the

unit, remove the disc and wait for about an hourfor

it

to

dry out; otherwise the unit will

not

operate

properly.

To

maintain high sound quality

Do

not splash liquid onto

the

unit or discs.

•

Do

not expose discs

to

direct sunlight or heat

sources such

as

hot air ducts, nor leave

it

in a car

parked

in

direct sunlight.

• Before playing, wipe the discs

with a cleaning cloth from the

center out.

Do

not use

solvents such

as

benzine,

thinner, commercially

available cleaners.

• This

unit

is

designed

to

play

back discs

that

conform

to

the

Compact Disc

{CD)

standard.

DuaiDiscs and some

of

the music discs encoded

with copyright protection technologies do

not

conform

to

the

Compact Disc

(CD)

standard,

therefore, these discs may

not

be playable by this

unit.

•

Discs

that

this unit

CANNOT

play

-

Discs

with labels, stickers, or sticky tape or

paper attached. Doing

so

may cause a

malfunction, or may ruin

the

disc.

-

Discs

with non-standard shapes (e.g., heart,

square, star). Attempting

to

do

so

may damage

the unit.

- 8

em

{3

1/4

in) discs.

Notes on CD-R/CD-RW discs

• The maximum number of: {CD-R/CD-RW only)

-folders

{albums):

150

(including root folder)

-files

(tracks) and folders: 300 (may less than

300

if

folder/file

names contain many

characters)

-displayable

characters for a

folder/file

name:

32

(Joliet)/64 (Romeo)

20GB

•

If

the multi-session disc begins with a

CD-DA

session, it

is

recognized

as

a

CD-DA

disc, and

other sessions are

not

played back.

•

Discs

that this

unit

CANNOT

play

-CD-R/CD-RW

of

poor recording quality.

-CD-R/CD-RW recorded with

an

incompatible

recording device.

-CD-R/CD-RW which

is

finalized incorrectly.

-CD-R/CD-RW other than those recorded in

music

CD

format or

MP3

format conforming to

IS09660 Levei1/Level

2,

Joliet/Romeo or multi-

session.

D Folder (album)

~

MP3/WMA file (track)

®

(j)

®

@

®

•

You

can

connect

to

the following iPod models.

Update your iPod devices

to

the latest software

before use.

Compatible iPhone/iPod models

Compatible Model

USB

iPhone 5 0

iPhone

4S

0

iPhone 4 0

iPhone

3GS

0

iPhone

3G

0

iPod touch (5th generation) 0

iPod touch {4th generation) 0

iPod touch {3rd generation) 0

iPod touch {2nd generation) 0

iPod classic 0

iPod nano {7th generation) 0

iPod nano {6th generation) 0

iPod nano (5th generation) 0

iPod nano {4th generation) 0

iPod nano (3rd generation) 0

Sony MEX-N50000BT User manual

Popular Stereo System manuals by other brands