Sony KDL-46NX711 - 46" Bravia Nx700 Series Hdtv Guide

− 1 −
Additional Information for Using Sony Wall-Hanging Bracket (SU-WH500)
Additional Information for
Using Sony Wall-Hanging Bracket (SU-WH500)
Compatible TV models for this Wall-Hanging Bracket information:
KDL-60NX817/60NX810
KDL-55NX817/55NX811/55NX810
KDL-46NX810/46NX717/46NX715/46NX711/46NX710
KDL-40NX717/40NX715/40NX711/40NX710
For product protection and safety reasons, Sony strongly recommends that you use the
Wall-Hanging Bracket model designed for your TV and that the wall-hanging of your TV
is performed by Sony dealers or licensed contractors.
To Customers
Please provide your licensed contractor with this installation supplement as well as the instructions
(supplied with the SU-WH500 Wall-Hanging Bracket). Read these documents carefully for safety and
proper installation.
To Sony Dealers and Contractors
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Sufficient expertise is required in installing this product, especially to determine the strength
of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product
to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during
the installation. Sony is not liable for any damage or injury caused by mishandling or improper
installation.
For proper installation, follow your wall-hanging bracket instructions and the directions below.
A-DSZ-100-12(1)

− 2 −
Additional Information for Using Sony Wall-Hanging Bracket (SU-WH500)
Installing the Wall-Hanging Bracket
Refer to the Instructions supplied with the SU-WH500 Wall-Hanging Bracket to properly carry out the
installation.
Open the Wall-Hanging Bracket package and check for all the required parts along with the Instructions.
1 Decide where you want to install your TV.
Make a mark on the Paper Template supplied with the Wall-Hanging Bracket that indicates
the screen center of your TV, referring to the Screen center dimension in “Dimensions
Table” at gure below.
Decide on the installation location, referring to your TV’s dimension and the screen center
mark on the Paper Template, and tape the Paper Template to the wall.
Dimension Table
Screen center point
"
#
$
%
&
Unit: inches (mm)*2
Model Name 
KDL-60NX81*155 1/8
(1,400)
33
(836)
13 3/8
(339)
30 1/4
(768)
1 15/16
(48)
KDL-55NX81*150 1/4
(1,276)
30 3/8
(770)
12 1/8
(305)
27 3/4
(702)
1 7/8
(47)
KDL-46NX81*1/
KDL-46NX71*1
42 3/4
(1,083)
26
(660)
9 7/8
(250)
23 3/8
(592)
1 7/8
(47)
KDL-40NX71*137 1/4
(944)
23
(582)
8 5/8
(217)
20 5/8
(521)
1 7/8
(47)
*1In the actual model names, the “” indicates numbers and/or characters specic to each model.
*2The measurement unit for the Paper Template supplied with the Wall-Hanging Bracket is in millimeters.
Figures in the above table may dier slightly depending on the installation.
CAUTION
e wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV.
Refer to your TV’s operating instructions for its weight.

− 3 −
Additional Information for Using Sony Wall-Hanging Bracket (SU-WH500)
2 Install the Wire Bracket on the wall.
Refer to the Instructions for SU-WH500.
3Disconnect all the cables from the TV.
4 Detach the Table-Top Stand from the TV, if necessary.
Remove the screws indicated by the arrow marks on the TV.
Table-Top Stand attached to TV. Table-Top Stand not attached to TV.
KDL-60NX817/
KDL-60NX810
Joint
KDL-60NX817/
KDL-60NX810
✍
• Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on
the TV.
• When removing the Table-Top Stand from the TV, lay the TV face down on a stable work surface that is
larger than the TV.
• To prevent damaging the surface of the TV, make sure to place a so cloth on the work surface.
• When liing or moving the TV, keep a so cloth underneath to prevent damage.
• e number and position of the screws on the rear of the TV diers, depending on the model of TV; be
sure to read the operating instructions of your TV.
• Be sure to remove the joint when the Table-Top Stand is not attached to the TV.
CAUTION
• If pressure or shock is applied to the surface of the TV, the TV may break or become damaged.
• Lay the TV face down on a stable and level surface with the Table-Top Stand hanging over the edge of
the surface. Having the TV face and the base of the Table-Top Stand on the same level surface will create
an unstable working condition and can damage the TV.
• When detaching the Table-Top Stand from the TV, hold the Table-Top Stand securely with both hands.

− 4 −
Additional Information for Using Sony Wall-Hanging Bracket (SU-WH500)
5 Attach the other items supplied with the Wall-Hanging Bracket and cables.
Screw
Pulley
Soft cloth
Attach the Pulleys to the upper two screw holes (see illustration above) using screws
supplied with SU-WH500.
✍
• For 60-inch model only, it is necessary to attach the Cushions supplied with SU-WH500.
Attach the Tilt-up Bracket and the Support Belt. (Refer to the Instructions for SU-WH500.)
Connect the cables.
6 Install the TV on the wall.
Refer to the Instructions for SU-WH500.
Make sure that you carry out this task with at least two or three people.
Do not attempt to li the TV by yourself.
For holding and carrying the TV, refer to your TV’s instructions.
✍
• When you put the TV back on the Table-Top Stand, reverse the above steps.
• Available TV models vary depending on the country/region.
• e availability of this Wall-Hanging Bracket (SU-WH500) varies depending on the country/region.