Southern Enterprises Bainbridge BT7870A0TX User manual

Page |
1
PO#:
BT7870A0TX/BT7870B0TX
Bainbridge Corner Vanity Sink
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore.com

Page |
2
1) Quantity
of 1
Marble Top
2L) Quantity
of 1
Left Side Panel
2R) Quantity
of 1
Right Side Panel
3) Quantity
of 1
Faux Drawer Front Panel
4) Quantity
of 1
Bottom Rail
5)Quantity
of 2
Back Top Rail
6) Quantity
of 2
Back Lower Rail
7) Quantity
of 1
Back Post
8) Quantity
of 1
Bottom Panel
9) Quantity
of 1
Drawer Front Panel
10L) Quantity
of 1
Drawer Side Left
10R) Quantity
of 1
Drawer Side Right
Bainbridge Corner Vanity Sink
Parts List
Please check packaging for all parts and hardware before discarding. Before beginning assembly, separate each
type of hardware. Carefully study the diagrams below and check that you have all parts indicated.
Call Customer Service if missing any hardware. Using the incorrect hardware will cause damage.

Page |
3
11L) Quantity
of 1
Drawer Back Panel Left
11R) Quantity
of 1
Drawer Back Panel Right
12L) Quantity
of 1
Drawer Vertical Panel Left
12R) Quantity
of 1
Drawer Vertical Panel Right
13) Quantity
of 1
Drawer Back Panel Middle
14) Quantity
of 1
Drawer Bottom Panel
15) Quantity
of 1
Top Metal Frame
16) Quantity
of 5
Leg
17) Quantity
of 1
Metal Shelf Frame
A) Quantity
of 15
Cam Bolts
B) Quantity
of 15
Cam Lock
C) Quantity
of 18
Wood Dowel Dia :8*30
D) Quantity
of 3
Wood Dowel Dia :6*30
E) Quantity
of 9
Wood Dowel Dia :6*20
F)Quantity
o f 2
Knob

Page |
4
G)Quantity
o f 2
Small Bolts
Dia.5/32”*7/8”L
H)Quantity
o f 2
Small Bolts Dia.5/32”*1-3/8”L
I) Quantity
of 16+2
Screw Dia.8*1”L
J) Quantity
of 6
Bolts. Dia:1/4”*1-3/8”L
K) Quantity
of 13
Bolts. Dia:1/4”*5/8”L
L) Quantity
of 21
Flat washer
M) Quantity
Of 21
Spring washer
N ) Quantity
of 1
Allen wrench
O) Quantity
of 5
Bolts. Dia:1/4”*1/2”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth. Avoid rubbing or
scratching the surface with rough or abrasive objects.
For replacement parts or
questions, please call SEI
Customer Service at
1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
5
Do not overtighten cam bolts. Stop when they feel secure.
Figure 1
Insert Cam Locks (B) into
corresponding holes on Faux
Drawer Front Panel (3) and Bottom
Rail (4).
Screw Cam Bolts (A) into threaded
holes on Left Panel (2L).
Attach Left Panel (2L) to Faux
Drawer Front Panel (3) and Bottom
Rail (4)by inserting Cam Bolts (A)
and Wood Dowels (C/D) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 2
Insert Cam Locks (B) into
corresponding holes on Faux
Drawer Front Panel (3) and Bottom
Rail (4).
Screw Cam Bolts (A) into threaded
holes on Right Panel (2R).
Attach Right Panel (2R) to Faux
Drawer Front Panel (3) and Bottom
Rail (4) by inserting Cam Bolts (A)
and Wood Dowels (C/D) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
BAINBRIDGE CORNER VANITY SINK
Assembly Instructions
2R
D
3

Page |
6
Figure 3
Insert Cam Locks (B) into
corresponding holes on Back Rails
(5/6)
Screw Cam Bolts (A) into threaded
holes on pre-assembled unit from
Figure 2.
Attach Back Rails (5/6) to
pre-assembled unit from Figure 2
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 4
Insert Cam Locks (B) into
corresponding holes on
pre-assembled unit from Figure 3.
Screw Cam Bolts (A) into threaded
holes on Back Post (7).
Attach Back Post (7) to
pre-assembled unit from Figure 3
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
5
6
A
A
C
A
7
A

Page |
7
Figure 5
Insert Cam Locks (B) into
corresponding holes on Back Rails
(5/6).
Screw Cam Bolts (A) into threaded
holes on pre-assembled unit from
Figure 4.
Attach Back Rails (5/6) to
pre-assembled unit from Figure 4
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 6
Attach Handle (F) to
pre-assembled unit from Figure 5
with Small Bolts (G).
Tighten Bolts (G) with Phillips
screwdriver (not included).
Attach pre-assembled unit from
Figure 5 to Bottom Panel (8).
5
6
A
A
A
A
F
8

Page |
8
Figure 7
Connect pre-assembled unit from
Figure 5 to Bottom Panel (8) with
Bolts (J) and Washers (L/M).
Tighten Bolts (J) with Allen Wrench
(N).
Figure 8
Attach Drawer Vertical Panels
(12L/12R) to Drawer Back Panel
(13) with Screws (I) and Wood
Dowels (E).
Tighten Screws (I) with Phillips
screwdriver (not included).
12L
12R
13
E
E
I
I
I
I

Page |
9
Figure 9
Attach Drawer Back Panels
(11L/11R) to pre-assembled unit
from Figure 8 with Screws (I) and
Wood Dowels (E).
Figure 10
Insert Drawer Bottom Panel (14)
into grooves of pre-assembled unit
from Figure 9.
14
11L
11R

Page |
10
Figure 11
Attach Drawer Side Panels
(10L/10R) and Drawer Front Panel
(9) to pre-assembled unit from
Figure 11 with Screws (I) and
Wood Dowels (E).
Tighten Screws (I) with Phillips
screwdriver (not included).
Figure 12
Attach Handle (F) to
pre-assembled unit from Figure 11
with Small Bolts (H).
10L
10R
9