Southern Enterprises BT7811A0TX User manual

Page |
1
PO#:
BT7811A0TX/BT7811B0TX
Mirage Vanity Sink
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore.com

Page |
2
A) Quantity
of 1
Top Panel
B) Quantity
of 1
Back Splash
C) Quantity
of 1
Left Side Panel
D) Quantity
of 1
Right Side Panel
E) Quantity
of 1
Front Upper Bar
F) Quantity
of 1
Back Upper Bar
G) Quantity
of 1
Back Lower Bar
H) Quantity
of 1
Fixed Shelf Panel
I) Quantity
of 1
Bottom Panel
J) Quantity
of 1
Drawer Façade
K1) Quantity
of 1
Drawer Fronts panel
K2) Quantity
of 2
Drawer Back Panel
Mirage Vanity Sink
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

Page |
3
K3) Quantity
of 1
Drawer Side Left
K4) Quantity
of 1
Drawer Side Right
K5) Quantity
of 1
Drawer Vertical Panel Left
K6) Quantity
of 1
Drawer Vertical Panel Right
K7) Quantity
of 2
Large Drawer Bottom Panel
K8) Quantity
of 1
Small Drawer Bottom Panel
K9) Quantity
of 1
Middle Drawer Back Panel
1) Quantity
of 15
Large Bolts. Dia:1/4”*1-3/8”L
2) Quantity
of 21
Spring Washer
3) Quantity
of 21
Flat Washer
4) Quantity
of 1
Allen Wrench
5) Quantity
of 20
Wood Dowel
6) Quantity
of 4
Knob
7) Quantity
of 4
Small Bolts
Dia.5/32”*1-1/8”L
8) Quantity
of 2
Ball Bearing Slide

Page |
4
9) Quantity
of 6
Screw (Ø3*16mm)
10) Quantity
of 2
Metal Plate
11) Quantity
of 6
Medium Bolts Dia:1/4”*5/8”L
12 ) Quantity
of 26
Screw Dia.8*1”L
13 ) Quantity
of 4
Rubber Gasket
14 ) Quantity
of 4
Covers
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the finish. Avoid rubbing
or scratching the surface with rough or abrasive objects.
For replacement parts or
questions, please call SEI
Customer Service at
1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
5
Figure 1
Attach Ball Bearing Slide (8)
to Side Panels (C/D) with
Screws (9).
Tighten Screws (9) with
Phillips screwdriver (not
included).
Place Right Side Panel (D)
to the side until Figure 5.
Figure 2
Insert Wood Dowels (5) into
pre-drilled holes on Left Side
Panel (C).
Attach Upper Bars (E/F) to
assembled unit from Figure
1 - Left Side Panel (C) with
Large Bolts (1) and Washers
(2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Mirage Vanity Sink
Assembly Instructions

Page |
6
Figure 3
Insert Wood Dowels (5) into
pre-drilled holes on Left Side
Panel (C).
Attach Fixed Shelf Panel (H)
and Back Lower Bar (G) to
assembled unit from Figure
2 with Large Bolts (1) and
Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Figure 4
Insert Wood Dowels (5) into
pre-drilled hole on Left Side
Panel (C).
Attach Bottom Panel (I) to
assembled unit from Figure
3 with Large Bolts (1) and
Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).

Page |
7
Figure 5
Insert Wood Dowels (5) into
pre-drilled holes on
assembled unit from Figure
4.
Attach assembled unit from
Figure 1 - Right Side Panel
(D) to assembled unit from
Figure 4 with Large Bolts (1)
and Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Figure 6
Turn assembled unit right side
up.
Attach Back Lower Bar (G)
to assembled unit from
Figure 5 with Large Bolt (1)
and Washers (2/3).
Tighten Large Bolt (1) with
Allen Wrench (4).

Page |
8
Figure 7
Attach Knobs (6) to
assembled unit from Figure
6 with Small Bolts (7) and
Rubber Gaskets (13).
Tighten Small Bolts (7) with
Phillips screwdriver (not
included).
Figure 8
Attach Drawer Vertical
Panels (K5/K6) to Middle
Drawer Back Panel (K9)
with Screws (12).
Tighten Screws (12) with
Phillips screwdriver (not
included).

Page |
9
Figure 9
Attach Drawer Back Panels
(K2) to assembled unit from
Figure 8 with Screws (12).
Tighten Screws (12) with
Phillips screwdriver (not
included).
Figure 10
Attach Drawer Side Panels
(K3/K4) to assembled unit
from Figure 9 with Screws
(12).
Tighten Screws (12) with
Phillips screwdriver (not
included).

Page |
10
Figure 11
Insert Drawer Bottom
Panels (K7/K8) into grooves
of assembled unit from
Figure 10.
Cover interior screw hole
with Covers (14).
Figure 12
Attach Drawer Front Panel
(K1) to assembled unit from
Figure 11 by inserting
Screws (12) to front.
Tighten Screws (12) with
Phillips screwdriver (not
included).