Southern Pride SPK-500-SL User manual

1234567
1234567
1234567
1234567
1234567
1234567
1234
1234
1234
1234
SPECIFICATIONS
MODEL SPK-500-SL
COOKING CAPACITIES FOR THE SPK-500
Pork Butt (7 lb.) 80 pieces 560 lb. total
St. Louis Ribs (2.75lb.) 75 pieces 206 lb. total
w/Optional Rib Racks 160 pieces 440 lb total
Chicken (3lb.) 120 pieces 360 lb. total
Brisket (12 lb.) 40 pieces 480 lb. total
Spare Ribs (3.5lb.) 60 pieces 210 lb. total
SPK-500-SL
Electrical Requirements: 120 volts AC, 60 hertz,
1 phase, 15 amp wiring required.
Gas Requirements: 75,000 btu, 1/2 NPT
Construction: Inner Liner: 14 gauge H.R. Steel
or 14 gauge Stainless Steel. Exterior: 22-gauge
Polished Stainless Steel
Firebox: 14” Diameter 1/4” thick H.R. pipe.
1/4” thick firebox door. Uses wood logs or charcoal.
Capacity: 2-3 logs 4-6” dia. 12-16” long.
Dimensions: 70
1/4” tall, 64 1/4” wide, 75 1/4” deep
(including covers) w/19” legs
Shell Dimensions: 57
1/4” tall, 52 1/4” wide, 67 1/4” long
.
Food Racks: Rotisserie with five (3) hanger racks,
each with three (3) 12”x 42” food racks (15 Total).
52.5 Sq.Ft. of Cooking Surface.
3 1/2” Spacing between food racks.
Air Circulation: Low Velocity Convection Fan.
Temperature Range: 100-325 degrees F.
Burner: Electronic Pilot Gas Burner
(Specify Natural or L.P. gas.)
Approvals:UL,ULC,NSF
Venting: See back page for venting instructions.
6” Flue
10” Flue
51 1/4"
19"
521/4"75 1/4"
67 1/4"
701/4"
25 1/2"
21"
12"
11"
19"
10"
22"
16"
17"
5 1/2"
5 1/2"
26 1/8"
12 1/2"
751/4"
671/4"
64 1/2"
Front View SideView
TopView
NOTE:
Dimensions Show
position of the 10”
flue on the optional
smoke extractor on
the -SLSE Model.
NOTE:
Drawings Show
the Optional
Smoke Extractor
on SLSE Models.
Optional Smoke
Extractor
Optional Smoke
Extractor
Electrical
Connection
for VSP Hood
Shown with Optional
DigitalControls
Electrical
Connection
for VSP Hood
21/2"
10"

SPK-500-SL
VENTING INSTALLATION
9/1/04
NOTE 1. When installing an Oven through a
wall constructed of combustible material, use
the Southern Pride Insulation Kit between
the oven and the wall.
2. The room that the face of the oven is installed
into should have a balanced or positive air pressure.
If the room has negative air pressure, smoke could
escape into the room during operation.
SUPPLIED BY SOUTHERN PRIDE: (*)
Smoke Extractor Damper with 10” chimney adapter plate
SUPPLIED BY CUSTOMER:
6” All Fuel Chimney, 6” Rain Cap, and all accessories
necessary for installation of the 6” chimney.
10” All Fuel Chimney, Exhaust Fan (NOTE: Fan must
be listed for use as a commercial kitchen ventilator),
fan curb, and all accessories necessary for installation
of the smoke extractor system.
ANY VENTILATION SYSTEM MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES. CONSULT WITH
LOCAL OFFICIALS AND A COMMERCIAL KITCHEN VENTILATION CONTRACTOR PRIOR TO INSTALLATION.
HOOD SYSTEM TO INCLUDE:
1. Ventilation Hood
2. Two speed fan (1380/2000)
3. Curb with vented extension and hinge kit
(Specify roof pitch)
4. Grease capture trough
5. Combustion chamber flue vent
SUPPLIED BY CUSTOMER:
6. Duct from hood to fan
VSP HOODS are U/L Listed to the applicable
Southern Pride oven models and are NSF Certified.
SPK-500-SL with recommended
optional VSP Vent Hood System.
THROUGH THE WALL -
DIRECT VENT INSTALLATION
VSP HOOD SYSTEM: Purchased through Southern Pride
10 ” AL L FU EL SM OKE
EXTRACTOR CHIMNEY
RAI N
CAP
NOTE: THE SIX INCH ALL FUEL CHIMNEY
SHOULD EXTEND ATLEAST3’ ABOVE THE
HIGHEST SIDEOF THE ROOF OPENING
AND BE ATLEAST2’ HIGHER THAN ANY
PORTION OF THE BUILDING WITHIN 10’.
HORIZON TAL.
6”ALL
FUEL
CHIMNEY
EXHAU ST
FAN
NOTE: THE 10” ALL
FUEL SMOKE EX-
TRACTOR CHIMNEY
TE R M IN A TE S A T
THE ROOF CURB
1
2
3 SPECIFYROOFPITCH
4
5
6
ALLMODELSMAYALSOBEINSTALLEDUNDERACANOPYHOODRATED
FORCOMMERCIALCOOKINGAPPLIANCES.
The oven’s minimum clearances from combustible materials are 18" on left side, 24" on right, 18" on top, 48"
from front, and 2" on back. Minimum clearances are 18" to chimney connector and to smoke extractor chimney
connector. Floor may be constructed of a combustible material. (Note: minimum clearance dimensions are from the
oven cabinet, not from component cover.) (If provision is made for access to service, minimum clearance can be
reduced to 2" on left side.) May be installed through a combustible wall with zero clearance with BBR kit No. 2099.
NOTE: If you have a duct longer than 10 feet or an elbow in your duct
your installation, it may require a larger capacity exhaust fan. Please
specify your duct requirements when ordering the VSP Hood System.
SouthernPrideDistributing,L.L.C. Phone: [phone]
2102 East Main Street - Marion, Illinois 62959 Fax: [phone]
www.southern-pride.com [email protected] [email protected] [email protected]
Sales: 800-851-8180 Service: 800-437-2679 Service Fax: [phone]