Soyal AR-723H User manual

SOYAL
ACCESS CONTROL SYSTEM
®AR-723H
V110713
P3
AR-WG-KEYBOARD AR-721-RBAR-821-RB
LED
BZ
123456
P1
P2
P3
P3
LED
BZ
12345678
AR-821RB
AR-723H
AR-723H
N.C.
LED
BZ
N.C.
N.O.
COM
CTL
12V
1
2
3
4
5
6
7
8
1
3
5
2
4
6
GND
ALM
PB
SEN
A+
B-
12V
Door
P2P1
GND
12V
WG 0
WG 1
7
6
5
4
3
2
1
P3
P3
GND
WG0
WG1
12V
AR-821RB
AR-723H
N.O.
GND
ALM
PB
SEN
A+
B-
12V
Door
P2P1
N.C.
N.O.
COM
CTL
12V
1
2
3
4
5
6
7
8
1
3
5
2
4
6
EXIT
DECODER
N.C.
N.O.
COM
CTL
12V
GND
PB
1
2
3
4
5
6
7
8
1
3
5
2
4
6
EXIT
AR-721RB
AR-723H
N.O.
N.C.
GND
ALM
PB
SEN
A+
B-
12V
Door
P2P1
(RS-485)
Diagram
Electric Strike
Electric Bolt
Request To Exit
Request To Exit
Blue
Red
Green
Black WG Keyboard
WG Reader
or
Alarm
Door Contact
or POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
Stand-Alone
Networking
Connect to Electric Strike Strengthen security with AR-721RB
Connect to Reader or KeyboardConnect to Door Contact and Alarm
Connector Table
(NO RS-485)
(Optional)
P4 TTL Cable
P3 WG Input Port P1
Standalone: 6 PIN
P2
Networking: 8 PIN + GND
When update rmware or set function for
standalone model, please order .
Please unplug cable before using cable.
P3
P4
P4
Content & Feature
1Product 2User Guide 5Feature 4Optional 3Terminal Cables
Standalone and Networking model for selection
1 Bi-color LED & 1 Buzzer
Built-in Watch Dog to prevent system from hanging
The Master Card function for adding/ deleting cards
Can set parameters by external keyboard
Application Wire Color Description
Power 1 Black DC 0V (GND)
R.T.E 2 Brown Negative Trigger Input
Power 3 Red DC 12V
Door Contact 4
Orange Negative Trigger Input
Alarm Relay 5 Yellow Open collector output
Lock Relay 6 Green Open collector output/
Security Trigger Signal
Application Wire Color Description
Power 1 Black DC 0V (GND)
2 Red DC 12V
Alarm Relay 3 Gray Open collector output
R.T.E 4 Purple Negative Trigger Input
Door Contact 5
Orange Negative Trigger Input
Lock Relay 6 White Open collector output/
Security Trigger Signal
RS-485 7 Blue RS-485 A+
8 Green RS-485 B-
Application Wire Color Description
1
2
3
WG 4 Blue WG DATA 1
5 Green WG DATA 0
Power 6 Red DC 12V
7 Black DC 0V (GND)
Application Wire Color Description
TTL
1 Yellow TX
2 White TE
3
Orange RX
4
5
Power 6 Red DC 12V
7 Black DC 0V (GND)
or
or
or
P4
Please unload the cover before plug in cable.
If you need to use cable, unplug cable and then plug in cable.
P3
P4 P3
Diode
※ are not in order, please refer to [Connector Table]
P1
※ are not in order, please refer to [Connector Table]
P1
※ are not in order, please refer to [Connector Table]
P1

V110713
323DMaster
TTL USB
7
6
5
4
3
2
1
P3
GND
12V
RX
TE
TX
2
1
Access Controller
About Master Card
Enter the program mode
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input 876112 → program mode accessed
Exit the program mode
Input
Operation process
M4/M8: Individual pass code
Card or PIN: Access programming mode → 12 UUUUU PPPP [e.g. User address: 00001 and pass code: 1234, input 12 00001 1234 ]
Card and PIN: Access programming mode → 13 UUUUU PPPP [e.g. User address: 00001 and pass code: 1234, input 13 00001 1234 ]
M6: Public pass word
Card or PIN: Access programming mode → 15 PPPP [Input 4-digit pass code, default value: 4321]
Card and PIN: Access programming mode → 17 PPPP [Input 4-digit pass code, default value: 1234; PPPP=0000: change into Card Only]
Enable controller
Access programming mode → 20 DDD [128= Anti-pass-back(0=Disable; 1=Enable)/ 064=Access/Exit(0=Exit; 1=Access).]
Access programming mode → 20 128 (Please refer to function default value for details.)
[e.g.] Enable Anti-pass-back, and set to Exit door= (128 x 1) + (064 x 0) = 128
Usually, anti-pass-back is commonly applied to parking areas in order to prevent from multi-entry with one card at a time, or to situations need
access and exit monitor.
C. Anti-pass-back(M4/M8)
B. Set up the password [Only for connect to external K-series reader]
Master Code modication
Access programming mode → 09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] Set the Master code to be 876112, input 123456 → 09 876112876112
A. Enter/ Exit Program Mode
Adding Tag
Present Master Card
Deleting All Tags
Present Master Card
P.S. Once MASTER CARD is presented after one
warning beep, all card data will be cleared.
After 3 short beeps
[Access programming mode]
After 3 short beeps
[Access programming mode]
Present one new card at a time
1 long warning beep after 2sec.
Present Master Card
[Exit programming mode]
5 short beeps after 5sec: cards cleared
1. 1.
2. 2.
3.
3.
4.
4.
MASTER CARD Setting for Stand-Alone
Use the MASTER CARD software
Input the MASTER CARD number, and press [Write].
Cut off and then transmit the power, the master card number will be activated.
Present the card, and the reader will ash green light 3 times and sound 3 beeps. Then the card becomes MASTER CARD and accesses programming
mode.If MASTER CARD is presented again, it will exit programming mode.
Black
Orange
White
Yellow
Converter
Red
[e.g.] No. 154 enable the anti-pass-back, and induction into the door has not been induced to leave. When he represent into the door will become
invalid , then he needs to set the reset. Access programming mode → 26 00154 00154 2 → Reset
[e.g.] User address from 00152 to 00684 enable the anti-pass-back function: 26 00152 00684 0
Enable card
Access programming mode → 26 SSSSS EEEEE N
[SSSSS= User address start; EEEEE= User address end; N=0(control)/ 1(Not control)/ 2(reset)]
D. Lift control
Enable
Access programming mode → 24 002 [002= enable lift control]
Connect with AR-401RO16B to control oors which the user will be able to access.
Plug in cable instead of cable, the wire connection is as below gure. After connection, then have power transmission to controller.P4 P3

SOYAL
ACCESS CONTROL SYSTEM
®AR-723H
V110713
Enable: Access programming mode → Disable: Access programming mode →
Factory Reset by its commands
When the device is stand-alone (not networking)
Access programming mode → 20 016 → 24 064 → 26 00000 01023 1 → 28 000 → 29 29
※Note: After the Master Code is changed, factory reset doesn’t restore the Master Code back to 123456.
Enable/Disable Arming status (for M4/M8; Factory default armingcode is: 1234) :
Standby Mode
Enter Program Mode
After door open
The normal procedure to open door → Input 4 digit arming code →
Do not open the door
→ Input 4 digit arming code → Present valid card
※ [The normal procedure to open door] can refer to [Access Mode].
[e.g.] User address NO. 168, only to the 6th and the 20th oor:
Access programming mode → 21 00168 0 00100000 → 21 00168 2 00001000
Multi oors
Access programming mode → 21 UUUUU S FFFFFFFF
[UUUUU=User address S: 4 sets of lift control (Input: 0~3) FFFFFFFF: 8 oors setting (F=0=Disable, F=1=Enable)
Single oor
[e.g.] User address NO. 45, allow to access the 24th oor: 27 00045 24
Access programming mode → 27 UUUUU FF
UUUU=User Address FF=Floor number (01~32 oor)
Set Floor/ Stop
F
8
16
24
32
0
1
2
3
F
6
14
22
30
F
7
15
23
31
F
5
13
21
29
F
4
12
20
28
F
3
11
19
27
F
2
10
18
26
F
1
9
17
25
E. Setting Up the Arming [Only for connect to external K-series reader]
Alarm conditions:
1. Arming is enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: Arming is enabled and the power is suddenly off then on.
Function Default Value
Mode4 / Mode6 / Mode8
※ Mode 6, the number of users up to 65535, since it reads CARD CODE(5 digits) only, unlike that Mode4/Mode8 read SITE CODE and CARD CODE(10 digits).
If Access Mode setting to use the PIN, it need to external the K-series Readers.
Selection= 0(none value)/ 1(1 x each value)
[e.g.] DDD value of Enable “Auto Open” + ”Exit by Push Button +
”Anti-pass-back”
=(0x1)+(0x2)+(1X4)+(1x16)+(0x32)+(0x64)+(1x128)=148;
As a result of that, the command will be 20 148 .
20 DDD ※Default Value
Function Selection Value Application
Attendance ※0: Yes 1: No 001 Networking
Auto Re-lock ※0: Disable 1: Enable 002 Networking/Stand-Alone
Auto Open ※0: Disable 1: Enable 004 Networking/Stand-Alone
Door open button input 0: Disable ※1: Enable 016 Networking/Stand-Alone
Master Controller of Network
※0: Slave 1: Mater 032 Networking
Access/Exit ※0: Exit 1: Access 064 Networking
Anti-pass-back ※0: Disable 1: Enable 128 Networking
24 DDD ※Default Value
Function Selection Value Application
Auto-open door without cards at auto open zone
※0: Disable 1: Enable 001 Networking/Stand-Alone
Alarm Output/ Lift Control ※
0: Alarm Output 1: Lift Control 002 Networking/Stand-Alone
Stop Alarm by door close or by push button
0: None ※ 1: Yes 064 Networking/Stand-Alone
28 DDD ※Default Value
Function Selection Value Application
Dual Door Control ※0: Disable 1: Enable 064 Networking/Stand-Alone
Force Open Alarm Output ※0: Disable 1: Enable 128 Networking/Stand-Alone
Mode Networking/
Stand-Alone
User
Capacity Access Mode Auto-show Duty time
Event log
Capacity
120
Holidays
Anti
force
Time
Zone
Lift
Control
Anti-pass-
back
M4
Networking/
Stand-Alone
1,024
1.Card only
2.Card and PIN
(4-digit PIN) +
3.Card or User address
(5-digit) + Individual PIN (4-digit
individual PIN)
+
Yes 1,200 Yes Yes No 32 Yes
M6 Stand-Alone 65,535
1.Card only
2.Card and PIN
(4-digit public PIN= Arming PWD)
+
3.Card or PIN
(4-digit public PIN= Duress code)
No No No No No No No
M8
Networking/
Stand-Alone
1,024
1.Card only
2.Card and PIN
(4-digit individual PIN)
+
3.Card or PIN
(4-digit individual PIN)
Yes 1,200 Yes Yes No 32 Yes

V110713
Access Controller
Command List
Function Command Description Mode
Entering programming mode PPPPPP PPPPPP=Master Code, default value=123456 M4/M6/M8
Exiting programming mode M4/M6/M8
Exiting programming mode and enabling arming status M4/M8
Node ID setting (Connecting to 716E 00 NNN NNN=Node ID, range: 001~254 M4/M8
Node ID setting (Connecting to PC directly without
via 716E) 00 NNN VVV nnn NNN=Node ID of Access Controller, VVV=Virtual 716E Node ID, nnn=Door number; range:001~254 M4/M8
Mifare tag / card format (Optional) 01 N
N: 0=ISO14443A; 1=ISO14443B; 2=ISO15693;
3=I Code1; 4=I Code2
PS.1. Please select the compliance,rst.
2. Make sure reader and card using the same compliance.
M4/M8
Door relay time setting 02 TTT
TTT=Door relay time 000= Output constantly
001~600=1~600 sec.
601~609=0.1~0.9 sec.
M4/M6/M8
Alarm relay time setting 03 TTT TTT=Alarm relay time 000= Output constantly 001~600=1~600 sec. M4/M6/M8
Control mode setting 04 N N=Mode 4=Mode4; 6=Mode6; 8=Mode8 M4/M6/M8
Arming delay time setting 05 TTT TTT=Alarm relay time 001~600=1~600 sec. M4/M6/M8
Alarm delay time setting 06 TTT TTT=Alarm delay time 001~600=1~600 sec. M4/M6/M8
Master card setting 07 SSSSS EEEEE SSSSS-EEEEE=00000-01023 (00000-03000 for AR-725H);
SSSSS=Starting user address; EEEEE=Ending user address M4/M8
Auto-open time zone setting 08 N HHMMhhmm 7123456H
N= 0(1st time zone) / 1(2nd time zone)
HHMM= Starting time; hhmm= ending time
(i.e.: 08301200=08:30 to 12:00)
7123456H= 7 days of week (Sun/Mon/Tue/Wed/Thu/Fri/Sat)+ Holiday
(H= 0: disable; 1: enable); Holidays establish by the software.
M4/M6/M8
Master code setting 09 PPPPPPRRRRRR PPPPPP=New master code
RRRRRR=Repeat the new master code M4/M6/M8
Setting
Suspend tag(M6) 10 SSSSS EEEEE =Suspend =Delete;
SSSSS=Starting user address, EEEEE=Ending user address
M4/M6/M8
Delete tag(M4) 10 SSSSS EEEEE M6
Set a sequence of cards as "read and access" 11 SSSSS EEEEE SSSSS=Starting card number; EEEEE=Ending card number M4/M8
Active the suspended cards 11 SSSSS EEEEE SSSSS=Starting user address; EEEEE=Ending user address M4/M8
Set the cards as Card mode OR PIN mode by user
address 12 UUUUU PPPP Access mode: Card or PIN; UUUUU=user address;
PPPP=4-digit pass code 0001~9999 M4/M8
Set t he cards as Card AND PIN mode by user
address 13 UUUUU PPPP Access mode: Card and PIN; UUUUU=user address; PPPP=4-digit pass code 0001~9999 M4/M6/M8
M4: Duress code setting
M6: Public PIN setting (Card or PIN) 15 PPPP PPPP=4-digit pass code (default value=4321)
P.S. Duress code will be unavailable and become a public PIN at access mode “Card or PIN” of M6 M4/M8
Card number modication 16 UUUUU SSSSSCCCCC UUUUU= User address; SSSSS=5-digit site code;
CCCCC=5-digit card code M4/M6/M8
M4: Arming pass code setting
M6: Public PIN setting (Card and PIN) 17 PPPP PPPP=4-digit pass code ( default value=1234; disable Arming PWD=0000)
P.S. Arming PWD code will be unavailable and become a public PIN at access mode “Card PIN” and of M6 M4/M6/M8
Door open waiting time 18 TTT TTT=Door open waiting time: 001~600=1~600 sec.; default value: 15 sec. M4/M8
Set the card by induction 19 UUUUU QQQQQ UUUUU=User address;
QQQQQ=Card quantity(00001=Continuously inducting) M4/M6/M8
Reader additional setting 20 DDD Please refer to function default value for details. M4/M6/M8
Lift control setting: multi-doors 21 UUUUU S FFFFFFFF UUUUU=User address, S=4 sets of lift control(0~3); FFFFFFFF=8 assigned oor
(F=0: Disable, 1: Enable) M4/M8
Add/Delete tag by induction (M6 only) 22 N N=0(Delete tag); N=1(Add tag) M6
AR-401ROsite number dip switch 23 NNN TTT NNN=site number, TTT= relay time: 000~600=1~600 sec. M4/M8
Controller parameter setting 24 DDD Please refer to function default value for details. M4/M6/M8
Controller time clock setting 25 YYMMDDHHmmss YYMMDDHHmmss: Year/ Month/ Day/ Hour/ Min./ Sec. M4/M6/M8
Anti-pass-back (Enable user) 26 SSSSS EEEEE N SSSSS=Starting user address; EEEEE=Ending user address;
N=0/Enable; N=1/Disable; N=2/Initial M4/M8
Single oor setting 27 UUUUU FF UUUUU=User Address; FF=Floor (01~32 oor) M4/M8
Dual door control/ Active or inactive arming for force open 28 DDD Please refer to function default value for details. M4/M6/M8
Delete all tags 29 29 M4/M6/M8
Enable the security trigger signal ( with AR-721RB) 34 064 (Enable)
34 000 (Disable)
To Change the "Door Lock" become the security trigger signal, when
controller is connected with AR-721RB. M4/M6/M8
9
9