SmartRG SR505n User manual

SR505n
Quick Start Guide

Installation
Connect one end of the supplied DSL cable to the port labeled DSL on the gateway
and connect the other end to the DSL wall jack installed by your provider.
For all other devices, connect an Ethernet cable from that device to any of the
LAN ports on the gateway.
Plug the power cord into the wall outlet and into the power jack on the back of
the gateway. For additional protection, connect the power cord to a surge pro-
tector.
Turn on the unit by pressing the power button on the gateway.
Your gateway is now automatically being set up to connect to the Internet. This
process may take a few minutes to complete before you can begin using your Inter-
net applications (browser, email, etc.). If you are unable to connect to the Inter-
net, verify that all cable connections are in place and that the router’s power is
turned on.

POWER LAN 1-4 WL AN WPS DSL INTERNET
DSL sync in progress
DSL sync acquired and gateway online
Gateway online and data transfer in progress
IP connection failure
WiFi enabled on modem
PC / network activity / data transfer
WPS Setup procedure in progress
WPS Connection completed successfully
: On : Off : Blinking / Active
LED INDICATORS
The LEDs on the front of SR505n
can assist you in better understanding
the current state of your gateway.

Quick Gateway Configuration
Logging in to your gateway
To change the settings on your gateway, you must log in the gateways' interface. Make sure
that you have completed the steps in "Installation" before you begin.
Open your internet browser application and type 192.168.1.1 into the address line.
1

The following screen appears. Wait while the gateway connects to your service pro-
vider. When the connection is complete, OK appears in green letters next to the Net-
work icon.
3
Click the Manage gateway (advanced) link in the upper right. The login dialogue
appears.

You may log in with the factory default credentials shown below.
User Name: admin
Password: admin
Click the Log In button in the
lower right.
Note: Your service provider
may use other settings. Please
contact your provider for login
information.
Manual Configuration of the WAN
If the automatic connect process is unsuccessful, refer to the Advanced Setup > Layer 2
Interface and WAN Services sections of the Gateway User Manual to manually establish a con-
nection.

WiFi Setup
Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this
page for both methods, and then follow the instructions for the method you desire.
In the left navigation bar, click Wireless ->Basic.
If not already selected, click Enable
Wireless.
If desired, in the SSID field, enter the
network name to which you want your
client devices connected. Continue
with the steps in the method you
prefer.

WPS Method
If the device you wish to connect to the Internet via your SmartRG gateway sup-
ports the WPS secure WiFi connection method, you may follow these steps.
1. In the left navigation bar, click Wireless -> Security.
2. Select Enable WPS and click Apply/Save to commit your selection.
3. On the back of the gateway’s exterior, press the button labeled WPS.
4. Within 2 minutes, activate WPS on the 3rd party device to which you wish to
connect. It may have a pushbutton on its exterior or a software interface is
used to initiate WPS connection. To learn how to use the WPS feature on
your client device, refer to its documentation.
Your device should now be connected to your router wirelessly using WPS. If you
encounter problems with the WPS setup such as connection failure, refer to your cli-
ent device for further instructions.

Manual Method
Set up your gateway’s parameters first, then:
1. In the left navigation bar, select Wireless >Security and scroll down to the Manual
Setup AP section.
2. If your gateway supports multiple wireless networks, select the SSID of the network
you wish to configure. You will need this ID for step 7.
3. Select the desired Network Authentication. Make sure that the host devices you
intend to use support the selected authentication type.
4. Choose a WPA Passphrase and type it in this field. You will need this passphrase for
step 7.
5. Select any desired encryption preferences in the lower three fields.
6. Click Apply / Save.
7. Follow the WiFi connection instructions provided with your client device to connect
to the router. Use the SSID name you selected in Step 2. Then enter the passphrase
that you entered in step 4 in the network setup screen of your WiFi client device.

Record Your SR505N WiFi Settings
Preset wireless settings on your
router
If you change the preset wireless
settings
WiFi network name
(SSID)
Network key (pass-
word)
Additional Support
If you require further instructions, please contact your local ISP Support.
SmartRG Inc., an ADTRAN company. All rights reserved. © 2020