spaceslide INTERIOR DRAWER UNIT User manual

UNB_PDU_INSTR_01.19Page 1 of 4
V1
CONTENTS:
1x Top panel
1x Back panel
1x Side panel (right)
1x Side panel (left)
1x Drawer infill panel
1x Base
4x Soft close drawer runners
(2x left, 2x right)
1x Metal infill strip
2x Drawer backs
2x Drawer sides (left)
2x Drawer sides (right)
2x Drawer fronts
2x Drawer bases
We recommend assembling on a soft surface
(e.g a carpet). If this isn’t possible, use a
protective cover on your hard surface floor.
16x
Wooden
dowels
20x
Wooden
dowels
12x
Euro
screws
4x
Cams
14x
Cams
14x
Dowels
4x
Dowels
INTERIOR UNIT PACK
DRAWER PACK
• Tools: Pozidrive screwdriver
RECOMMENDED:
HOW TO BUILD
THE INTERIOR
DRAWER UNIT
Assembly Instructions
Carcass unit
Drawer unit
98-RDS
5
2x
Glue*
*A drop of glue needs to be added into all holes the
wooden dowels are placed into (items 3 & 7).

UNB_PDU_INSTR_01.19
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
Page 2 of 4
1 2 3
4Apply to both panels (D&C).
1 - Insert the dowels and cams into the drawer inll (E).
2 - On the metal strip (H) remove the plastic backing from the
double-sided tape then stick the metal strip to the inll (E).
Apply to both panels (A&F).
x4
5 6
Lay panel (D) on a at surface. (Shown from the side).
x8
x4
x3
x1
x3
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
C
D
D
DC
x2
x2
1
2
x8 x6 x2
x7
Slot infill (E)
onto the
sticky side of
the tape on
the drawer
infill strip (H).
Back
panel
Side
panel

UNB_PDU_INSTR_01.19Page 3 of 4
Insert the screws into the holes shown on both sides (D & C).
Left-hand runner shown above.
5
x2
10 (Repeat on all drawer sides). (Repeat on all drawer fronts).
10 11
MAKING THE DRAWERS
x1
x4 x2
9
x3
FIX THROUGH THESE HOLES HIGHLIGHTED
1 2 3
7 8
C
C
D
D
If the top panel (A) won’t locate, loosen the
cams in the back panel (B).
If the base panel (F) won’t locate, loosen the cams in the back panel
(B). Once in place, tighten the cams.
x4 x4
Top panel
Back panel
Cams
Top panel
Back
panel
Base
Shown from underneath:
Cams

UNB_PDU_INSTR_01.19Page 4 of 4
1 2 3
1 – Lay drawer side (J) on a at surface, insert the base (M) into the groove then hold the back panel (I) in place. 2 – Place the other drawer side (K) over the base and fasten the back panel (M).
3 – Turn the drawer around and add the drawer front (L) . (Repeat on all drawers).
12
PRELIMINARY DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
QUOTATION PURPOSES ONLY
ISSUED DRAWING
ISSUED BY: A.SIMMONS
ISSUE DATE:18/06/12
ISSUED TO: SUPPLIER
13
1 - Pull the sliding part of the lower drawer runners out and sit
the drawer on top. Whilst holding the runners in place, slide the
drawer back until the drawer clicks into place.
2 - Use the locking button to secure the drawer. Repeat for all
drawers. To remove a drawer, reverse the operation.
1 2
x2 x2
Drawer base
Drawer base
Drawer side
Drawer back
Drawer side
Drawer back
Drawer front
Pull the sliding part of the lower
drawers out first and hold in place.
Drawer shown
from underneath.
Locking button
Turn to
adjust height