Argos Baby Amelie 226/1380 User manual

If you need help or have damaged or missing parts, call the
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 100 cm
Depth - 50 cm
Height - 117 cm
Baby Amelie-
Assembly Instructions 226/1380 - Please keep for future reference
Customer Helpline: 08456 400 800
Dressing table with stool
Issue 1 - 06/05/14

Note:if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
.Check you have all the
components and tools listed on
pages 2 and 3.
.Remove all fittings from the
plastic bags and separate them
into their groups.
.Keep children and animals
away from the work area, small
parts could choke if swallowed.
.Make sure you have enough
space to layout the parts before
starting.
.Do not stand or put weight on
the product, this could cause
damage.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
.Assemble the item as close
to its final position (in the same
room) as possible.
.Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
Avoid placing the furniture in
Use an appropriate furniture .From time to time check
that there are no loose
screws on this unit.
.This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
.
.
direct sunlight as this will cause
the timber to prematurely age.
polish for natural wood
furniture and a dry cloth to
clean the product.
Safety and Care Advice
Important -
.
.
Please read these instructions fully before starting assembly

2
Components - Panels
Please check you have all the panels listed below
3
4

3
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
Tools required
30 mm Wooden dowel x 36 30 mm Screw x 73 12 mm Screw x 13
12 mm Screw x 8 Right runner x 2
Nail x 12
Knob x 2 20 mm Bolt x 2
Please check you have all the fittings listed below
A B C
FED
G H I
K
J
Left runner x 2
Locking nut x 10Metal dowel x 10
60 mm Bolt x 16
L
Allen key x 1
O
Wall strap x 1 Washer x 1
NM
F1
F2
E2
E1

4
Assembly Instructions
A
Step 1
Fitting Wooden Dowels:
Insert dowels into holes in
the indicated parts.
G
Fitting metal dowel
Screw metal dowel into small
top panel and fronts drawer
.
Step 2
16
Note: Insert metal
dowels as far as
shown.
Do not over tighten.
9
13
9
Step 3
Fix runners and into the
pre-drilled holes on left side ,
right side and middle panel
using screws as shown.
EF
C
Make sure runners
are positioned as
shown.
B
Attach corner to top rail
and using screws .
Make sure corner
in flush to the edge
of the rail as shown.

5
Assembly Instructions
Step 4
Attach side rails through
corner using screws .
Atach top frame to pre
drilled holes in mirror frame
using screws .
Step 5
4
B
8
3
3
4
4
4
4
25
14
13
B
A
Make sure corners
are is flush to edge of
the rail as shown.
In flush
B
Insert dowels into holes in
the indicated parts.
Fix the support frames rail to
mirror frame using screws
.
13
25

Assembly Instructions
Step 6
Step 7
6
L
Fix dressing feet to corners
using bolt and allen key
, through the pre-drilled
holes, as shown.
5
3
4
4
Attach side rails and top
rails and to top panel
using screws .
2
4
B
31
25
O

7
Assembly Instructions
Step 8
Step 9
Step 10
9
H
Carefully lay down the
top on a clean and soft
surface to avoid
damaging the product.
Insert the left side panel and
middle panel to the top
panel .
Insert 4 locking nuts into left
side panel and middle panel
where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
10
7
Attach front rail and back
rail to side panel and
middle panel using screws
.
12
11
B
8
10
H
a) Insert right side panel to
the top panel and rails
and as shown.
Insert 2 locking nuts into
right side panel , where
shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
b) Attach front rail and back
rail to side panel using
screws .
H
9
12
11
B
9
8
H
8
10
711
12
9

Assembly Instructions
Step 11
Step 12
21
8
I
Carefully turn the cabinet
upright.
Fix back panels within
rebates using nails .
Important: Cabinet
MUST be 'square' when
back is attached.
21
A
Insert dowels in to holes a top
panel .
Place the cabinet on the table
through the dowels as shown.
1

Assembly Instructions
Step 13
Step 14
9
Drawer assembly
H
A) Attach drawer sides and
to the drawer front .
Insert 2 locking nuts into left
and right side drawer and ,
where shown.
Use a screwdriver to turn locking
nuts clockwise to lock.
Do not over tighten.
B) Slide drawer bottom in to
slots on drawer sides and .
C) Attach drawer back to
drawer sides and using
screws .
D) Fix knob using bolts .
E) Fix runner and using
screws as shown.
12
JK
11
B
13
17 18
18
20
1117
Make sure finished
side face inside the
drawer.
EF
D
A) B) C)
E)
Finished side
to face inside
20
(2x)
(2x)
(2x)
(2x)
Fix the supports frame in the
pre drilled holes in top panel
and using screw .
1
15
B
H
16
17 18
7
7
15
7