spaceslide Dressing Table User manual

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
Page 1 of 6
DRESSING TABLE
CONTENTS:
A1x Lid (with mirror)
B 1x Lid inll
C1x Top panel (left)
D 1x Top panel (right)
E1x Back panel
F1x Inside back panel
G 1x Left outer side panel
H 1x Left inner side panel
I1x Right inner side panel
J1x Right outer side panel
K4x Soft close drawer runners
(2x left, 2x right)
L1x Base
M1x Front panel
N1x Decorative panel
O4x Legs
P2x Drawer backs
Q2x Drawer sides (left)
R 2x Drawer sides (right)
S2x Drawer base
T1x Drawer fronts (left)
U1x Drawer fronts (right)
V4x Soft close clips (2x left, 2x right)
W4x Leg mounting plates
• TOOLS: Screwdriver & Hammer
• TWO PERSON BUILD
RECOMMENDED:
V2
Assembly Instructions
8x
One piece
connectors
8x
Plastic
dowels
1x
Soft close hinge
(right-grey)
8x
Euro Screws
36x
Cams
2x
Soft close
hinge cover
34x
Wood Screw
(3.5x16mm)
36x
Dowels
1x
Hinge brackets
pair
(left & right)
1x
Soft close hinge
(left-white)
8x
Wooden dowels
2x
Wood Screw
(4x18mm)
2x
Wall mounting
brackets
1x
Wood glue 2x Cable hole plug
We recommend you use the Wall Mounting
Brackets provided to fix the dressing table to
a wall (where possible). This will prevent the
unit being pulled over. Use suitable fixings.

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
(Ensure the Cams are facing inwards).
6
Page 2 of 6
3
Note: H panel shown
5
Repeat on both panels (H&I).
Push/tap sides (H&I) onto panel (F).
Lay panel (L) on a at surface.
12
x3
x3
x5
4
x10
x1
x10
3
x4
Fit the Cams (10) on the sides of the panel and the dowels
(11) in the centre.

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
Repeat on both
panels (G&J).
x3 x4
10
Lay panels on a at surface and apply glue to all 8 holes.
1 –tap dowels into panel (M). 2 – insert panel (N) on top.
Page 3 of 6
x4
9
STEP 1
STEP 2
8
Screw through holes shown on both sides, at both ends of the unit.
x2
x2 x2
x2 x2
7
INSIDE DRAWER RUNNERS OUTSIDE DRAWER RUNNERS

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
Page 4 of 6
15
14
x4
13
x7
x2
x7
16
(Shown from underneath). (Shown from back).
17 Insert legs into holes and turn until tight.
Fit leg mounting plates to all 4 corners.
(Shown from underneath).
x4
x16

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
Page 5 of 6
2018
67
19
x2
x2
x2
9
9
9
Repeat on both sides of opening. Slot hinges over brackets.
x8
Slide the lid (A) behind the hinges and screw into place.
(2 people needed). Then slide the covers (8) over.
Tap plastic dowels gently into place with a hammer.
(Repeat on both drawers).
21
x2
x2
x2
8
SQUEEZE SIDES
THEN INSERT
PIN
22 23
Push/tap sides (R&Q) onto back panel (P).
(Repeat on both drawers).
PIN
Drawer back
(Repeat on both drawers).

Call: 0800 9803499 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information
Page 6 of 6
1
2
2524
W
W
x4
9
Fix the Wall Mounting Bracket to the bottom of the Dressing
Table. (Use suitable xings when attaching to the wall).
We recommend you use the
Wall Mounting Brackets
provided to x the dressing
table to a wall (where
possible). This will prevent
the unit being pulled over.
Use suitable xings.
WALL MOUNTING
BRACKETS
1 – Slide the drawers so that the prong goes into the hole in the back of the drawer.
2 – Pull the sliders forward, until you hear a click, repeat on both sides.
USE SUITABLE
WALL FIXINGS
x2

www.spaceslide.co.uk/installation-and-technical-information Call: 0800 9803499 SS_INSTRUC_DTP_08.2015
Page 1 of 1
1 2
3 4
DRESSING TABLE
POWER CUBE
242mm
Remove cable covers.
Feed plug through and x power cube. Position no more than 242mm from the front.
Assembly Instructions
V1