Spacetronik SPE-G110 User manual

12
34
12
2 1
Bx8
M6x20
x4
C
4x4
75mmx45mmx1.5mm
2-stage & enhanced column
50KG
25mm/s
1255mm
755mm
1200mmx600mmx25mm MDF
SPE-G110
500mm
70mmx40mmx2mm
ST4.2x32
42
5 6
1
24
3
5
2
1
Install the left column
2
3
D
4x4
D
A
B
A
x4
M6x12
C
D
10
D
Tighten
D
A
4
21
7 8
6
7
Ax4
M6x12
D
5x5(With cross)
x1
x1
C
ST4.2x32
B
x8
M6x20
x4
D
5x5(With cross)
x1
Dx1
D
4x4
x1
9
1
910
ST4.2x19 2
Item No.: SPE-G110
Installation guide
Item No.
Column Design
Maximum Lo ad
Max Speed
Highest Position
Lowest Position
Height range
Outer tube
Desktop
Inner tube
Accessory List
Attention: The drawings below are only for reference which might be slightly different from the actual object, please in kind prevail. Any tools missing
or installation problems, please contact the customer service firstly.
Part List Installation Instruction
No. Part Qty No. Part Qty
Handset
Switch cordFeet cover
Lifting column coverCable management
Power plugFeet
Left lifting
column set
Tabletop set
Install the lifting column
STEP1
Rotate the column after
inserting it to the bottom
to avoid height difference
longside of the
lifting column
Shortside of the desktop
Note: The method of installing the left column is
the same as that of the right column, and the
direction is the same.
Insert
1.Insert the column coupling into the
gear box as shown in the figure.
2.Rotate the left column to the position shown
in the figure to avoid the screws, and rotate it
counterclockwise after fully inserting it.
3. Rotate it as shown in the figure. Then use 4x4
allen key to tighten two M6x12 screws. The
installation completes.
4. The installation of the other side column
is the same as that of the left column, and
the direction is the same.
STEP2 Install the feet
5x5(With cross)
STEP3
Connect the feet to the column, use a 4x4 wrench
to screw M6x20 and tighten them, and use a 5x5
wrench to screw ST4.2x32 self-tapping screws to
fix the lifting column cover and the feet cover.
Install the key button
Place the key button in the position shown in the figure, align the
two holes of the table as shown in the figure, and not align the
other holes. Use a 5x5 hex wrench with a cross to screw two
ST4.2x19 self-tapping nails and fix them.
Technical Data
8
10

DMTrade Mikolaj Tomaszewski declares that the devcie complies with the
directives EMC (2014/30/EU), LVD (2014/35/EU), RoHS (2011/65/EU +
2015/864/EU).
●“▲”
●“▼”
3
5
55
5
STEP4 Install the cables
Removable
Stick
Fix the cables to the tabletop with cable
management(5) to keep the desk clean
Ripped Organize the lines Fixed
50
4
Connect the power cord to the adapter.
One end of the switch cord is connected
to the adapter, the other end is connected
to the handset, and the motor line is
connected to the handset.
Instruction
Lifting Function:
adjust the height of desk by pressing the button“▲”or ”▼”
Reset Function:
(1) When at the lowest position, long press the button ”▼” for more
than 5 seconds to enter the reset state. The reset is completed
until the lifting system hits the bottom and rebounds to stop.
(2) When the lifting system has the problem, release the button.
Then, long press the button ”▼” ,the reset is not completed until
the lifting system hits the bottom and rebound to stop.
Resistance function:
(1) Built-in sensor, when encountering any objects, the device
instantly stops and reverses to avoid damage.
(2) Long press “▲” and ”▼” bottoms for more than 5 seconds to
turn on of off the resistance function.