Indiana Furniture Square One 17-2424BL User manual

800.422.5727 www.IndianaFurniture.com
Model Description 17-6
Quantity
17-2424BL Single Block, 24"x24“
(4 Bolts & Nuts Included) 24
17-17596EC End Cap, 96" 3
(used horizontally)
17-17597EC End Cap, 97-3/4" 4
(2 used vertically, 2 used
horizontally)
17-17596CP Corner Post, 96" 1
(used horizontally)
17-LEVKIT Leveler Kit, 2 Levelers 4
17-12MMBOLTKIT 12mm Bolt Kit, qty 8 1
Square One
Assembly Instructions
17-6
Tools Needed:
Components:
A
A
B
B
B
C
D
E
C
D
17-6 Page 1 of 3
8x8x8
E
Before You Start:
•Reference local building and construction codes.
•Contact the building’s Facility Manager for proper installation. Indiana Furniture does not provide
floor or wall-mounting hardware.
•Requires one side mounted to the wall AND we recommend a floor anchor as well.
Drill 5mm & 4mm
Allen Keys
Box Level Tape
Measure
Ladder 3to 4
Installers
6mm Allen Key
Driver Bit
NOTE: Anchoring to floor or wall may require additional tools and hardware. See note at end of instructions.

800.422.5727 www.IndianaFurniture.com
Square One
Assembly Instructions
17-6
17-6 Page 2 of 3
6
8x8x8
Begin by building a 2’ x 8’ row of blocks. To establish
the configuration footprint.
Align the holes in blocks and connect with 2, 80mm
bolts and 2, 17mm nuts.
Fasten the bolt and nut together but do not
over tighten because you will want to align
and firmly tighten upon final setup.
In the bottom row of blocks install the levelers. Use
the 6mm Allen Key Driver Bit to install the threaded
insert into the bottom holes of the block.
It is important that the threaded insert is
installed as close to perpendicular as possible.
Thread the leveler into the insert. Then thread a
17mm nut onto the top of the leveler.
Install the rest of the blocks using the 80mm bolts
and 17mm nuts until the 8’ x 8’ wall section is built.
Connect a 96” Corner Post and 2, 97-3/4” End Caps
on the wall section using the 60mm bolts.
Build 2, 2’ x 8’ ceiling sections using the 80mm bolts
and 17mm nuts.
Connect a 96” End Cap and a 97-3/4” End Cap to
either side of the ceiling sections using the 60mm
bolts.
1
2
3
4
5
6
7
17mm nut
Threaded
Insert
Leveler
4
80mm bolt
60mm bolt
17mm nut
Cap, Post, or Beam
2
5
2
96”
Corner Post
97-3/4”
End Cap
97-3/4”
End Cap
97-3/4”
End Cap
96”
End Cap
8
8

800.422.5727 www.IndianaFurniture.com
96”
End Cap
96-5/8”
Square One
Assembly Instructions
17-6
17-6 Page 3 of 3
Attach the 2 ceiling sections to the wall section using
the 60mm bolts. Make sure the 97-3/4” End
Caps are on the outside of the configuration.
Mount a 96” End Cap horizontally on the wall spaced
96-5/8” from the floor to the bottom of the End Cap.
See note about wall anchoring at the end.
Using a ladder and some assistants, lift the
configuration up and secure it to the End Cap on the
wall using the 60mm bolts.
Install 12mm bolts into any unused inserts in Corner
Posts and End Caps.
Using a box level to check level, adjust the levelers
on the configuration so they are all touching the
floor.
Once everything is leveled, go back and align
components. This may require loosening bolts and
nuts to align. Once adjusted to satisfaction, tighten
hardware to a secure fit.
Your configuration is complete.
If adding Acoustical or Tackable Panels, Acrylic
Inserts, Dry Erase Boards, or TV Mounts, see
individual instructions for installation.
Wall / Floor Anchoring:
Additional support is required for configurations that
are not free standing. Anchoring to the floor, wall,
ceiling, and other furniture will require additional
tools and hardware, not provided by Indiana
Furniture. The installer is responsible for sourcing
hardware and for the installation of support per
building conditions.
8
9
10
12
8x8x8
8
9
14
10
11
13
14
97-3/4”
End Cap