Spacetronik SPE-S122WO User manual

1
Desktop Assemblyx1
Lifting column x2 Feetx2
Knob Screwx1
6
3
Ax8
Bx1 C
x12
x3
D
M6 5x5(With cross)
M6
ST4.2 4x4
12
15
2
1
6
7
1
x3
A
A
Bx4
D
4x4
Cx8
D
4x4
C
D
D
5x5
D
B
2
3
1
D
Hand switchx1
11
D
A
4
Adaptorx1 Cable mountsx4Cablex1
Joint Table Board Assemblyx1 Adjustable Table Board Assemblyx1
Left Adjusting Railx1 Right Adjusting Railx1
Power plug x1
23
4 5 6 7
10 11 12
1
2
713
14
10
11
4
5
8 9
Supporting plate1x1 Supporting plate2x1
13 14 15
9
8
Item No.: SPE-S122WO
Installation guide
Technical Data
Five-range height adjustment, each 25.4mm,
maximum 12KG
25mm/s
100-240V
730mm
1230mm
0~40 °C
2
Maximum Load
(Joint Table Board)
Maximum Load
(Adjustable Table Board)
Max Speed
Input Voltage
Lowest Position
Highest Position
Duty Cycle
Applicable Temperature
Continuous operation for 2 mins at most after
pause for 18 mins
50KG
2
Column Number
Maximum Load
(Whole Desk)
230*600mm
Main Desktop Size
Joint Desktop Size
580*265mm
Adjustable Desktop Size
1100*600mm
Accessory List
Attention: The drawings below are only for reference which might be slightly different from the actual object, please in kind prevail. Any tools missing
or installation problems, please contact the customer service firstly.
Part List Installation Instruction
STEP1
STEP2
STEP3
Install the lifting column
Rotate the column after
inserting it to the bottom
to avoid height difference
Shortside of the desktop
longside of the
lifting colum
Install the lifting column (2) to the
tabletop(1), then tighten the
screws (B) with allen key (D) Tighten the screws(B) with 4x4 allen key
Insert
Screws
Rotate the column after inserting
it, making the screws on the
supporting beam into the column slot
Insert the hexagon head of the column
along the wiring trough, the side of the
wire head facing the motor
Install the feet
Install the feet (4) to the lifting columns (2) with the
screw (C)and tighten it with 4*4 wrench (D)
Install the hand switch
Position the hand switch (3) as shown in the picture to align
the three screw holes on the tabletop, then fix it with the
screw (A)and tighten it with 5*5 wrench (D)

3
5
4
Bx4
D
4x4
B
D
10
12
12
11
13
15
15
15
15
8
9
2
9
B
D
Bx4
D
4x4
STEP4 Install and adjust the desktop
assembly
The direction of the arrow on the adjusting rail points to the direction
of the control box
The reserved hole is close to
the side of the control box
Preformed
Hole
Put the adjustable table board (3) into the
notch of the main table board, and align
the screw slot of the adjusting rail(4) with
the screw and insert it vertically
Insert
Align the holes on the left adjusting
rail (4) with the holes on the table,
fix it with the screw (B), and tighten
it with a 4x4 wrench (D)
Install the right adjusting rail (5) same as the
left adjusting rail. After fixing it, screw the knob
screw (10) into the proper position
STEP5
STEP6
Install the joint table board
Fix the supporting plate 2 (9) on the joint table board assembly (2)
with screws (B), and tighten it with a 4x4 wrench (D). The operation
of supporting plate 1 (8) is the same as above
Insert
Insert the table board with the supporting
plate into the main table board as shown
in the figure
Finished product
Connect all cables to the adaptor
Insert the adaptor(12) to the bracket of the tabletop
Connect the switch cable
to the DC port
Connect the motor cable
to the M1 port
Fix the cables to the tabletop with cable
management(15) to keep desk clean
Ripped Fixed
Organize the lines
Attention
Fault phenomenon Method
No response while long pressing
down arrow after connected with
a power supply
1.Check if all the cables be connected well
1.Check if all the cables be connected well
2.Contact your supplier or dealer
2.Contact your supplier or dealer
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
1.Check if overloaded, max loading: 50kg;
1.Check if overloaded, max loading: 50kg;
1.Check if overloaded, max loading: 50kg;
2.Contact your supplier or dealer
2.Contact your supplier or dealer
2.Contact your supplier or dealer
The motor not move as instructed 1. Contact your supplier or dealer
1.Reposition
2.Contact your supplier or dealer
Go down but not go up
Downward sliding
Frequently Reposition
Overwork
（Duty cycle:Max 2min on/18min OFF）
1.Restart after suspend for 18mins while
connecting with power;
2.Contact your supplier or dealer;
Common fault treatment
The following tips will help you detected and eliminate the common fault and error.
If the fault you met is not listed below, please contact with your supplier. Only the
manufacturer and professionals are capable for investigating and correcting
those fault and error.
1. Power supply: AC100V-240V,50/60HZ
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when
cleaning, be careful not to let the drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in
accordance with each country's environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when playing, so any
dangerous consequences caused by this improper action will not be on manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on
the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner
used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a
similarly
qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter the
tools around. Always be careful to treat the packaging materials in order to avoid any possible danger,
e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in transportation.
Not enough up&down height
2.Contact your supplier or dealer.
1.Perform a reset operation;
This marking indicates that this product should not
be disposed with other household wastes. To
prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmental safe recycling.
Wastedisposal
DMTrade Mikolaj Tomaszewski declares that the devcie complies with the
directives EMC (2014/30/EU),
LVD (2014/35/EU), RoHS (2011/65/EU + 2015/864/EU).