Spacetronik SPE-323T User manual

B8
D
E
16
12
24
C
4
F
7 1 8 1
3 2 4 3
1 3 2 3
5 1 6 1
1
91
2
4
5
7
8
910
3
6
1
10
A6
M6
150KG
580-1230mm
G
6
6
H
1
I
C
E
C
E
I
4x4
Dx12
6
3
D
5
I
2
2
2
Cx12
I
4x4
I
C
1
2
C
E
3
Cx4
I
4x4
Ex4
I
5x5
4x4
5x5
4x4
5x5
4x4
5x5
Model:SPE-323T
Installation guide
Technical data
Column qty
Max Loading capacity
Height range
3
Accessory list
Attention: The drawings below are only for reference which might be slightly
different from the actual object, please in kind prevail. Any tools missing or
installation problems, please contact the customer service firstly.
ImageNo. Spec Qty
M6
M6
M6
M8
St4.2
St4.2
Wiring fixing seat
Wrench
4x4mm
Wrench
(with cross)
5x5mm
Component list
PartNo. Qty PartNo. Qty
PartNo. Qty PartNo. Qty
PartNo. Qty PartNo. Qty
PartNo. Qty PartNo. Qty
PartNo. Qty PartNo. Qty
Pedestal pad Lifting column
Supporting plate
Supporting beam
Left connecting plate Right connecting plate
Control box
Hand Switch
(Option)
Power Plug Cable
Note: This standing desk has three angle installation methods,
namely 90 °, 120 ° and 180 °
STEP 1 Install left and right connecting plates 90° Installation
120° Installation
180° Installation
Connect the two supporting beams (3) to the left and
right connecting plates (5) (6) with screws (C) and (E)
respectively. There are three angles to choose at will,
and finally tighten them with a wrench (I)
STEP 2 Install lifting columns
120° Installation
Connect the lifting columns (2) to the support beam (3)
with screws (D), the middle column (2) to the left and
right connecting plates (5) (6), and the wrench (I) to tighten
the screws; 90° and 180° are installed in the same way as 120°.
STEP 3-1 Install the Feet
Install the feet and the lifting column (2)
together, use wrench (I) to tighten the screws (C).
90° and 120° installation
5
6

F
F
F
Cx12
I
4x4
I
C
1
2
Gx6
Hx6
A C
H S M 1 M 2 M 3
10
Fx22
Fx22
Fx22
I
4x4
Ax6
A
I
22
4
F
F
F
BX8
I
4x4
B
B
B
BX8
I
4x4
BX8
I
4x4
3
56
7
8
9
STEP 3-2
180° Installation
Install the feet and the lifting column (2)
together, use wrench (I) to tighten the screws (C).
STEP 4
120° Installation
Install the supporting plate
Connect the left and right support plates (4) and the support
beam (3) with screws (A), connect the middle support plate (4)
with the left and right connection plates (5) (6), and tighten the
screws with a wrench (I); 90° and 120° are installed in the
same way as 120°
STEP 5 Connect All the Cables onto the Control Box
120° Installation 90° and 180° wiring is the same as 120°
Ripped
Cable
management Fixed
The wiring fixing seat (H) can be glued to the desk board, and
can also be screwed to the desk board with screws (G)
Port for
hand switch
Power port
Port for cable
connected to the
lifting column
STEP 6-1
STEP 6-2
120° Installation
90° Installation
STEP 6-3
180° Installation
Install the Tabletop and Hand Switch
The expansion of the supporting
beam can be adjusted according
to the actual use.
The control box is fixed
on the table
Fix the table board with screws (F) and
tighten it with a pistol drill
Loosen
Pull
Tighten
Loosen
Pull
Tighten
Loosen
Pull
Tighten
The control box is fixed
on the table
The control box is fixed
on the table
Fix the table board with screws (F) and
tighten it with a pistol drill
Fix the table board with screws (F) and
tighten it with a pistol drill
The telescopic distance of the beam can be
adjusted according to the actual use, the
adjustment method is the same as step 6-1
The telescopic distance of the beam can be
adjusted according to the actual use, the
adjustment method is the same as step 6-1

Common fault treatment
The following tips will help you detected and eliminate the common fault
and error. If the fault you met is not listed below, please contact with your
supplier. Only the manufacturer and professionals are capable for investigating
and correcting those fault and error.
Fault phenomenon Method
No response while long pressing
down arrow after connected with
a power supply
1.Check if all the cables be connected well
1.Check if all the cables be connected well
2.Contact your supplier or dealer
2.Contact your supplier or dealer
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
1.Check if overloaded, max loading: 150kg;
1.Check if overloaded, max loading: 150kg;
1.Check if overloaded, max loading: 150kg;
2.Contact your supplier or dealer
2.Contact your supplier or dealer
2.Contact your supplier or dealer
The motor not move as instructed 1. Contact your supplier or dealer
1.Reposition
2.Contact your supplier or dealer
Go down but not go up
Downward sliding
Frequently Reposition
Overwork
（Duty cycle:Max 2min on/18min OFF）
1.Restart after suspend for 18mins while
connecting with power;
2.Contact your supplier or dealer;
1. Press "M"and "3" together for 3 seconds or
more, after hearing continuous beeping for twice,
it will restore factory settings
Not enough up&down height
2.Contact your supplier or dealer
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
DMTrade Mikolaj Tomaszewski declares that the devcie complies with the directives EMC (2014/30/EU),
LVD (2014/35/EU), RoHS (2011/65/EU + 2015/864/EU).