Spagna Vetro Vetro SV156 -30/36" User manual

Spagna Vetro Range Hood
Under cabinet
Model SV156 -30/36”
Users Manual
7272 Buller Ave, Burnaby, BC, Canada.
Tel: [phone]
www.KitchenHoods.ca

- 1 -
INSTALLATION INSTRUCTIONS
★ Please check the following items before installation:
(A) Environment:
Keep the Range Hood far away form the window and for avoiding the air
convection if the evaporated oil does not raise to the 25cm effective range of the
suction power. The Range Hood will not be
effective.
(B) Height of installation:
The height of installation is measured form
the button of Range Hood to top of stove,
the recommended height is 28”-30”.
(C) Keep the hood in level:
Make sure the hood is in level when
install
Note:
The manufacturer / import /
wholesaler will not be hold responsible for
any damages to personal
property or real estate or any bodily
injuries. Whether caused
directly or indirectly by the Range Hood.
(B)
(C)
(D)
Level

- 2 -
OPERATION INSTRUCTIONS
1. SECURE BY 2 MOUNTING SCREW ATTACHED TO THE WALL.
2. LIGHT SWITCH: :ON
3. ON/OFF SWITCH ● :ON
4. SPEED SWITCH OF RIGHT BLOWER MOTOR.
R: O I : SLOW II : FAST
5. SPEED SWITCH OF LEFT BLOWER MOTOR.
L: O I : SLOW II : FAST
6. LIGHT COVER.
7. COVER.
8. SAFETY NET.
9. OIL CUP.
10. COVER OF THE TOP EXHAUST OUTLET.
11. COVER OF THE BACK EXHAUST OUTLET.

- 3 -
INSTALLATION
• A minimum of 6” round (standard for this range hood) must be used to
maintain maximum airflow efficiency.
• Always use rigid type metal/aluminum ducts if available to maximize airflow
when connecting to provided duct.
• ALWAYS, when possible, reduce the number or transitions and turns. If long
duct run is required, increase duct size from 6” to 7” or 8”. If a reducer is used,
install a long reducer instead of a pancake reducer.
Reducing duct size will restrict airflow and decrease airflow, thus reduce duct
size as far away from open in gas possible.
• If turns or transitions are required: Install as far away from opening and as
far apart, between 2, as possible.
• Minimum mount height between stove top to hood bottom should be no less
than 27-inch*.
• Maximum mount height between stove top to hood bottom should be no
higher than 30-inch*.
• It is important to install the hood at the proper mounting height. Hoods
mounted too low could result in heat damage and fire hazard; while hoods
mounted too high will be hard to reach and will loose its performance
and efficiency.
• If available, also refer to stove top manufacturer’s height clearance
requirements and recommended hood mounting height above range.
* Due to different ceiling height configurations, recommended height may not
be applicable.

- 4 -
ELECTRICAL REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances.
It is the customer’s responsibility:
• To contact a qualified electrical installer.
• To assure that the electrical installation is adequate and in conformance with
National Electrical Code.
If codes permit and a separate ground wire is used, it is recommended that a
qualified electrician determine that
the ground path is adequate.
A 120-Volt, 60 Hz, AC-only, fused electrical supply is required on a separate 15-amp
circuit, fused on both sides of the line.
DO NOT ground to a gas pipe.
Check with a qualified electrician if you are not sure that the range hood is properly
grounded.
DO NOT have a fuse in the neutral or ground circuit.
IMPORTANT: Save this Installation Guide for electrical inspector’s use.
The range hood must be connected with copper wire/plug only.
The range hood should be connected directly to the fused disconnect (or circuit
breaker) box through flexible armoured or non-metallic sheathed copper cable.
Listed strain relief must be provided at each end of the power supply cable.
Wire sizes (copper wire only) and connections must conform with the rating of the
appliance as specified on the model/serial rating label. Wire sizes must conform to
the requirements of the National Electrical Code
listed conduit connector must be provided at each end of the power supply cable (at
the range hood and at the junction box).SAFETY NOTES

- 5 -
Vent system must terminate to the outside (roof or side
wall).
• DO NOT terminate the vent system in an attic or other
enclosed area.
• DO NOT use 4” (10.2 cm) laundry-type wall caps.
• Use metal/aluminum vent only. Rigid metal/
aluminum vent is recommended.
• DO NOT use plastic vent.
• Always keep the duct clean to ensure proper airflow.
Installation without ducting
When installing the hood without ducting, please
ensure that a charcoal filter is fitted in the top air
vent .
1)When you are using a single motor, it is normal that
the ripple effect will cause the other fan to move.
2)The function of the activated charcoal filter is to
remove oil and soot result from cooking. However,
Oil and Soot will not be completely eliminated, as
this will cause the performance of the hood to
reduce significantly. (Please refer to Pt. A
above)
For the most efficient & quiet operation: Range hood
• A distance of 27” to 30” is recommended* between stove
top and the bottom of range hood.
• It is recommended that the range hood be vented vertically through the roof
through 6” or bigger round metal/aluminum vent work.
• The size of the vent should be uniform, Use no more than three 90° elbows

- 6 -
TROUBLESHOOTING
Problems Fixing
No electric power
1. Check the plug and the socket.
2. Check the wires.
The bulb does not light.
1.
Check whether the bulb is broken.
2. Check whether the switch is damaged
The motor does not rotate.
1.
Check whether the switch of the motor is
damaged.
2. Replace the motor if the switch is damaged.
Range Hood vibrates.
Check whether the blower is damaged.
Replace the
damaged blower.

- 7 -
WIRING DIAGRAM

- 8 -
SPECIFICATION
DIMENSION (W×D×H)
30”: 29
1
/
2
”×20
3
/
4
”×2
3
/
4
”
36”: 35
1
/
2
”×20
3
/
4
”×2
3
/
4
”
PACKING DIMENSION
30”: 32
1
/
5
”×6
1
/
10
”×22
4
/
5
”
36”: 38
1
/
5
”×6
1
/
10
”×22
4
/
5
”
ELEC. SPECIFICATION
120V 60Hz
EXHAUST DUCT
6” dia. or 8
1
/
2
”×2
1
/
2
”
TRANSMISSION STYLE
Twin Motors
LIGHTING SYSTEM
2 x 40 W (Max)
VOLUME 800 CFM
SPEED RANGES 1650 RPM
CURRENT 3A (For twin motors)
WEIGHT
30”: N.W. 10.5 KG
G.W. 12.5 KG