SPALDING M8809511 User manual

107/06 ID# M8809511
In-GroundBasketballSystem
OwnersManual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
WARNING!
Toll-Free Customer Service Number for U.S: 1-800-558-5234 Canada Only: 1-800-284-8339
Internet Address: http://www.hydra-rib.com
REQUIRED TOOLS AND MATERIALS:
• 3 Capable Adults
• Carpenter’s Level
• 15’ Tape Measure
•Sh
ovel & Post Hole
Digger
• Phillips Screwdriver
• (1) Utility Knife
• (2) Stepladders 8 ft. (2.4 m)
• Safety Goggles
•
• Container to Mix
• Optional: Large &
Small Adjustable
Wrenches
• (2 each) Wrenches and/or Socket Wrenches and
Sockets (Deep-Well Sockets are Recommended).
1/2"3/8" 9/16" 3/4" 15/16"
1/2"3/8" 9/16" 3/4" 15/16"
Write Model Number
From Box Here:
© COPYRIGHT 2006 by SPALDING

2
ID# M8809511 07/06
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
Owner must ensure that all players know and follow these rules
for safe operation of the system.
WARNING
• DO NOT HANG on the rim or any part of the system including
backboard, support braces or net.
• During play, especially when performing dunk type activities,
keep player's face away from the backboard, rim and net.
Serious injury could occur if teeth/face come in contact with
backboard, rim or net.
• Do not slide, climb, shake or play on base and/or pole.
• When adjusting height or moving system, keep hands and
fingers away from moving parts.
• Do not allow children to move or adjust system.
• During play, do not wear jewelry (rings, watches, necklaces,
etc.). Objects may entangle in net.
• Keep organic material away from pole base. Grass, litter, etc.
could cause corrosion and/or deterioration.
• Check pole system for signs of corrosion (rust, pitting,
chipping) and repaint with exterior enamel paint. If rust has
penetrated through the steel anywhere, replace pole
immediately.
• Check system before each use for proper ballast, loose
hardware, excessive wear and signs corrosion and repair
before use.
• Check system before each use for instability.
• Never play on damaged equipment.
• Keep pole top covered with cap at all times.
• See instruction manual for proper installation and
maintenance.
R ea d a nd und e r s t a nd w a r ning s li s t e d
b e low b e f o r e u s ing t hi s p r odu c t .
F
a ilu r e t o f ollow t h ese w a r ning s m ay
r es ul t in se r iou s inju r y a nd / o r
p r op e r t y d a m a g e .
ID#: 588000 05/05
In the U.S.: 1-888-713-5488 In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
In the U.S.: 1-800-334-9111
In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339
31
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
• If using a ladder during assembly, use extreme caution.
• Three (3) people are recommended for this operation.
• Seat the pole sections properly. Failure to do so could allow the pole sections to
separate during play.
• Before digging, contact utility company to locate underground power cables, gas,
and water lines. Ensure there are no overhead power lines within 20 ft. (7 m) radius
of pole location.
• Climate, corrosion, excessive use, or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6' 6" (1.98 m) to the bottom of backboard.
• This equipment is intended for home recreational use only and NOT
excessive competitive play.
• Read and understand the warning label affixed to pole.
• The life of your basketball pole depends on many conditions. The climate,
placement of the pole, the location of the pole, exposure to corrosives such as
pesticides, herbicides or salts are all important.
• Adult supervision is recommended when adjusting height.
• Serious injury could occur if teeth/face come in contact with backboard, net, or rim.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the
instructions carefully. Proper and complete assembly, use and supervision is
essential for proper operation and to reduce the risk of accident or injury. A
high probability of serious injury exists if this system is not installed,
maintained, and operated properly. Check entire box and inside all packing
material for parts and/or additional instructional material. Before beginning
assembly, read the instructions and identify parts using the hardware identifier
and parts list in this document.
For more information on assembly, placement, proper use and maintenance,
visit The American Basketball Council website at http://www.smarthoops.com.
WARRANTY CARD:
Please remember to complete your product registration form either on-
line at:
www.huffysports.com/customer_support/product_registration or
mail-in the enclosed postcard.

307/06 ID# M8809511
24" (61 cm)
36" (91.4 cm)
Ensure ground is level with playing
surface, then dig pole hole.
GROUND
SURFACE
PLAYING
SURFACE
1.
Install threaded ends of J-bolts (1) through holes in
mounting plate (3) and secure as shown.
2.
3
2
2
2
1
3.
1
Install nut (2) to J-bolt (1) as
shown. Repeat procedure for
other three J-bolts (1). 2-1/2”
(6.35 cm)
CONTACT UTILITIES
BEFORE DIGGING.
WARNING!
IMPORTANT!
Make sure nuts are 2-1/2”
(6.35cm) from top of
J-Bolts.
Make sure J-bolts (1) are
in the illustrated position.
NOTE:
Nuts on the top of plate are
used for leveling the pole after
system is fully assembled.
NOTE:

4
ID# M8809511 07/06
Fill hole with concrete. Tamp down concrete to release air
pockets and build drainage hill.
Insert J-bolts (1) from mounting plate (3) into cement as shown.
Move assembly around to release any air pockets in cement,
then rest mounting plate on cement drainage hill. Apply some
pressure to level mounting plate on top of drainage hill. Level
mounting plate and square with playing surface. Clean off any
excess cement on mounting plate at this time.
4.
5.
PLAYING SURFACE
3
1
IMPORTANT!
Front of mounting plate (3)
must be parallel with
playing surface.
WARNING!
DO NOT PROCEED UNTIL
CONCRETE HAS CURED! A
MINIMUM OF 72 HOURS. ALLOW
ADDITIONAL TIME FOR COLD,
WET OR HUMID WEATHER.
IMPORTANT!
Check leveling of mounting
plate several times with
carpenter’s level while
concrete is curing.

507/06 ID# M8809511
PLAYIN
G
SURFACE
Upright pole (5). Assemble lower pole flange
onto protruding J-bolts (1) as shown. The flange
will then rest on the nuts (2).
Secure pole (5) flange to mounting plate (3)
as shown. Tighten completely.
6.
7.
5
3
2
6
6
6
2
6
2
6
1
1
5
THREE PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY
AND/OR PROPERTY
DAMAGE.
WARNING!
Holes in pole must be
parallel with playing
surface.
IMPORTANT!
PLAYING SURFACE
Position crank jack
mounting as shown.
NOTE:
6
2
6
6

6
ID# M8809511 07/06
8.
7
14
27
13
27
12
12
27
27
27
27
14
27
13
7
THREE PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY
AND/OR PROPERTY
DAMAGE.
WARNING!
Beginning with upper support arm (8) secure support
arms to pole. Continue by securing lower support
arm (9) as shown.
IMPORTANT!
Do Not Over Tighten.
27
27
27
27
13
12
14
8
9
13 27
27

707/06 ID# M8809511
9.
IMPORTANT!
Do Not Over Tighten.
8
14
13 27
27
10
13
27
27
9
Secure backboard to support arms (8 and 9) as shown.
Use same hardware combination for attaching both elevator tubes to the
backoard.

8
ID# M8809511 07/06
PLAYING
SURFACE
10. Secure jack brackets (21) to to mounting bracket as shown.
21
21
11
11.
REAR VIEW
13
13 14
Position U-joint of crank jack (20)
as shown. Where tubes on crank
jack join, hold steady to keep both
tubes from rotating. Rotate handle
clockwise on crank jack to the
fully extended position.
NOTE:
20
IMPORTANT!
Hold Here.

907/06 ID# M8809511
12.
B.
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
WARNING!
12
14
27 27
13 27
27 13
REAR VIEW
IMPORTANT!
Do Not Over Tighten.
9
9
20
20
27
A. Replace spacer in jack (20) with spacer (4). Insert through top of
screw jack (20) as shown.
B. Install crank jack (20) U-joint to lower support arm (9) as shown.
20
4
A.
20

10
ID# M8809511 07/06
28
13 21
15
15
13
14
20
Some adjustment will be necessary
to align the lower crank jack and
bushings to jack brackets (21).
NOTE:
REAR VIEW
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
WARNING!
13. Rotate jack handle until jack (20) aligns with jack brackets (21). Secure crank jack (20)
to jack brackets (21) as shown.

11 07/06 ID# M8809511
7
8
9
1
0
1
0
9
8
7
16
17
16
17
Apply height indicator labels (18 and 19) to height indicators (16).
Attach height indicators (16) to lower arm in areas as shown by turning screws (17) into place with a
phillips screwdriver.
14. A.
B.
IMPORTANT!
Note Orientation of Height
Indicators: 10’ Mark Should
Face Away From Backboard.
78910
78910
78
9
10
78
9
10
Set-up For Right Side Set-up For Left Side
19
18
16 16

12
ID# M8809511 07/06
29
22
Attach rim assembly (29). For rim assembly, see
instructions included with rim.
Rim Assembly
16.
IMPORTANT!
Carefully cut and peel
protective film away from
board prior to attaching rim.
Remove rim cover
prior to installing rim
assembly to board.
Refer To Instructions
Included With Rim
Hardware For Rim
Assembly.
B. D.
C.
A.
15. Install net (30) to rim as shown.
30 30
24
23
25
26
25

13 07/06 ID# M8809511
Apply height adjustment label (31) to
front of pole as shown.
18.
REGULATION
RIM HEIGHT IS
10 FEET (3.05 m).
31
17. Check leveling at this time. Pole (5) should
be level in all directions. After system is
leveled, completely tighten nuts (2) above
pole flange.
If adjustment is necessary, adjust
system by rotating the nuts (2)
between mounting plate (3) and
pole flange.
NOTE:
5
2

14
ID# M8809511 07/06
Rotate crank handle to raise or lower backboard.
20.
Secure pole pad (32) as
shown.
19.
32
Height Adjustment
If height adjustment is difficult to
operate, you may have over
tightened the areas indicated.
NOTE:
Pole pad may NOT be
included in this model.
NOTE:

15 07/06 ID# M8809511
Item #10 (4)
Item #11 (3)
Item #17 (4)
Item #24 (2)
PARTS LIST
HARDWARE IDENTIFIER (BOLTS)
Item Qty. Part No. Description
1 4 200573 J-Bolt, 1/2-13 x 24” Long
2 12 265575 Nut, Hex, 5/8-11
3 1 900661 Anchor Plate
4 1 205714 Spacer, 0.53 I.D. x 1 O.D. x 5” Long
5 1 908284 Pole
6 8 200704 Washer, 5/8” x 1.5 O.D.
7 2 205125 Spacer, 0.53 I.D. x 0.75 O.D. x 1.88” Long
8 1 908282 Support Arm, Upper
9 1 908283 Support Arm, Lower
10 4 205711 Bolt, Hex Head, 1/2-13 x 2-1/4” Long
11 2 205516 Bolt, Hex Head, 1/2-13 x 5.75” Long
12 4 224728 Bolt, Hex Head, 1/2-13 x 9.25” Long
13 20 202651 Washer, Flat, 1/2”
14 11 206340 Lock Nut, Hex 1/2-13
15 2 205082 Spacer, 0.53 I.D. x 0.75 O.D. x .38 Long
16 2 204735 Height Indicator
17 4 204733 Screw, #8 x .050” Long
Item Qty. Part No. Description
18 1 204739 Label, Height Indicator, Right
19 1 204740 Label, Height Indicator, Left
20 1 222880 Crank, Jack
21 2 908292 Bracket, Crank Jack Support
22 4 205702 Nut, Hex, 3/8-16
23 2 205701 Bolt, Carriage, 3/8-16 x 3.5” Long
24 2 205700 Bolt, Hex, Tap, 3/8-16 x 3.5” Long
25 6 203309 Washer, Flat, 3/8”
26 4* 203300 Washer, 3/8 Locking,
27 28 204670A Bushing, Plastic
28 1 205076 Bolt, Hex, 1/2-13 x 5.5” Long
29 1 Rim
30 1 Net
31 1 200685 Label, Height Adjustment
32 1 216555 Pole Pad, Hydra-Rib (May Not Be Included)
1 216555S Pole Pad, Spalding (May Not Be Included)
* You May Have Extra Parts With This Model.
Item #23 (2)
Item #28 (1)

16
ID# M8809511 07/06
Item #25 (6)
Item #26 (4)*
Item #27 (28)
Item #7 (2)
Item #15 (2)
* You May Have Extra Parts With This Model.
Item #14 (11)
Item #2 (12) Item #13 (20)
Item #22 (4)
Item #6 (8)
HARDWARE IDENTIFIER (NUTS, WASHERS & STEEL SPACERS)
HARDWARE IDENTIFIER (PLASTIC & NYLON SPACERS)
Item #4 (1)