Speakman SA-2203 User manual

Instructions for Models:
SB-1811
SB-1811-E
Need Help?
For additional assistance or service call:
SPEAKMAN Company
400 Anchor Mill Road
New Castle, DE 19720
PHONE: [phone]
EMAIL: [e-mail]
WEB: www.speakman.com
92-SB-1811-R2
What You Need To Know:
Tools:
Required:
*Adjustable
Wrench
*Groove Joint
Pliers
*Phillips
Screwdriver
*Teflon Tape
Helpful:
*Supply Lines *Basin Wrench *Pipe Wrench
*Hacksaw *Tubing Cutter *Utility Knife
*Eye Protection
Important Notes:
Be sure to read instructions thoroughly before
beginning installation. Do not overtighten any
connections or damage may occur. This faucet has
an operating range of 20-80 psi.
Safety Tips:
Cover your drain to prevent loss of parts.
Be sure to wear eye protection while cutting pipe.
Maintenance:
Your new Lavatory Faucet is designed for years
of trouble-free performance. Keep it looking new
by cleaning it periodically with a soft cloth.
Avoid abrasive cleaners, steel wool, and harsh
chemicals as these will dull the finish and void
your warranty.
①
②
③
④
⑤
Slide Rubber Washer (1), and Metal Washer (2)
onto threaded shank of faucet. Thread Mounting
Nut (3) onto faucet shank until hand tight. Use phillips
screwdriver to tighten Mounting Screws (4), securing the
faucet to the sink.
Insert Drain Body (1) into drain hole of sink from
above.From underneath install Rubber Gasket (2),
Red Fiber Washer (3), and Lock Nut (4) in the order
shown below. Secure Lock Nut with Groove Joint Pliers.
Take care to not overtighten.
Install Rubber Washer (2) between Lower Drain
Pipe (3) and Drain Body (1). Thread Lower Drain
Pipe (3) onto Drain Body (1).
1
2
3
4
1
2
3
4
Connect Hose with red stripe (1), to HOT water
supply. Connect Hose with blue stripe (2), to the
COLD water supply. Use adjustable wrench to tighten
connections. Take care to not overtighten. Note: Angle
valves shown are not included.
1
2
HOT
COLD
3/8”
Compression
Fitting
1
2
34
1
2
3
Shut off water supplies. Remove old faucet. Clean
sink surface in preperation for installation of new
faucet. Place Faucet Body (1), Slip Ring (2), and
optional Deck Plate (3), as well as optional Putty
Plate (4) in order shown below.

⑥①RPG05-0914
②RPG05-0915 (1.5GPM)
③RPG45-0058
④RPG63-0090
⑤RPG04-0412 (-BN)
After installation is completed, remove aerator.
Turn on water supply and allow both hot and
cold water to run for at least one minute each to remove
the debris. While water is running, check for leaks.
Replace aerator.
IMPORTANT:
8.08”
[205mm]
4.85”
[123mm]
4.65”
[118mm]
MAX 1.38”
[35mm]
6.03”
[153mm]
1.97”
[50mm]
10°
MAX 1.38”
[35mm]
1
3
2
4
5
⑦RPG05-40126 (1.2GPM)

INSTRUCTIONS FOR MODELS
92-SA-2200-02
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SA-2203 TOWEL RACK
SA-2204 7” TOWEL BAR
SA-2205 PAPER HOLDER
SA-2206 ROBE HOOK
SA-2207 24” TOWEL BAR
TOOLS AND SUPPLIES
Phillips
Screwdriver
Pencil
Drill Drill Bit
Ø3/16”
Level
Hex Key
(included)
Phillips
Drive Bit
Additional warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives on any of the Speakman custom
finish products may damage the finish and void the
product warranty. Please be sure to only use approved
cleaners. Please contact Speakman for any clarification
of acceptable cleaners.
1The Mounting Plate (1) comes pre-installed in
the Accessory (2). Remove the Mounting Plate(s)
by loosening the pre-installed set screw at bottom
with the included Hex Key.
2At the selected height, mark center point of
mounting locations onto wall referencing
the rough in diagram.
3Align Mounting Plate over center point marked
in previous step. Mounting Plate should be
vertical with Notch in the cylinder (1) pointing to
the bottom as shown below. Mark Mounting
Screw locations onto the wall surface. Remove
items after marking mounting locations.
4If mounting directly to wood stud, Plastic Anchors
are not required. If mounting to tile, acquire
proper mounting hardware capable of supporting
the accessory in use. If mounting to drywall, drill
guide holes at marked locations using a Drill
equipped with a Ø3/16" bit.
Ø3 /16”
5Insert Plastic Anchors into drilled holes and screw
in the anchor using a Phillips Head screwdriver,
or a Drill equipped with a Phillips Driver Bit until
the head is flush with the wall surface.
OR

6Secure Mounting Plate with the Mounting Screws
provided. Verify that the Mounting Plate is
aligned vertically.
7Place Accessory (1) over Mounting Bracket and
secure the pre-installed set screw (2) with the
included Hex Key.
ROUGH-IN DIAGRAMS SPEAKMAN®
DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.
SA-2203
24"
610mm
26 1
16
"
662mm
10 1
16
"
255mm
43
16
"
106mm
SA-2204
95
16
"
237mm
23
4
"
70mm
21
16
"
52mm
75
16
"
185mm
SA-2205
11
16
"
18mm
75
8
"
193mm
5
16
"
8mm
23
4
"
70mm
1
4
"
7mm
3
8
"
10mm
SA-2206
23
16
"
56mm
11
16
"
18mm
3
8
"
10mm
23
4
"
70mm
SA-2207
2in
52mm
24"
610mm
26 1
16
"
662mm
23
4
"
70mm