INSTRUCTIONS FOR MODELS
92-SB-2401-01
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
www.speakman.com
SB-2401
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Adjustable
Wrench
10mm
Wrench
Safety
Glasses
Aerator
Wrench
(included)
Flat Tip
Screwdriver
Additional warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This faucet has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives may damage the finish and
void the product warranty. Please be sure to only use
approved cleaners. Please contact Speakman for any
clarification of acceptable cleaners.
1Make sure Rubber Gasket is inserted properly in
Faucet groove. If not, place Rubber Gasket over
Hoses and align to base of Faucet.
2Place Hoses, one at a time, thru hole in
mounting surface. Lower Faucet into position.
NOTE: If installing optional
Deck Plate, slip the Hoses
through the Deck Plate. Then
place Hoses, one at a time,
thru hole in mounting surface.
Lower Faucet into position.
Ensure a proper seal with
the Rubber Gasket to the
mounting surface. Make sure
the Deck Plate is properly
aligned to the Faucet.
3From below, install Rubber Washer (1), Metal
Washer (2), and secure with Mounting Nuts (3).
Align Faucet to desired position and wrench
tighten Mounting Nuts (3).
OR OR
4Make connections to water supplies. The inlet
threads of the faucet are 9/16”-24 UNF and will
accept a 3/8” Compression Fitting. Wrench
Tighten.
Accepts a 3/8”
Compression
Fitting
SUPPLY STOPS NOT INCLUDED
5Remove Stopper (1), Flange Nut (2), and Flange
Washer (3) from Drain Assembly.
6From beneath, insert Drain Assembly thru drain
hole in sink. Attach supplied Flange Washer (1)
or plumber’s putty to the underside of the Flange
(2). Secure Flange (2) to the Drain Assembly.
Align the Drain Assembly as shown below.
Align towards faucet.
7From beneath, secure Rubber Washer (1), Plastic
Washer (2), and Mounting Nut (3). Wrench
tighten.
8Remove Pivot Nut (1), from Drain Assembly.
Install Pivot Rod (2). Ensure that Inner Pivot
Washer (3) is retained in Drain Assembly. Insert
Pivot Rod into Drain Assembly and install Stopper
(4) as non-removable. Secure Pivot Rod to Drain
Assembly by tightening Pivot Nut (1).
9Place one end of Spring Clip (1), on Pivot Rod
(2). Insert Pivot Rod (2) thru a hole in the Lift Rod
Strap (3). Secure with Spring Clip (1).
10 Place Drain into the open position by pressing
downward on the Pivot Rod (1). Insert Lift Rod
(2) into Strap (3). Adjust height of Lift Rod (2),
and tighten Thumb Screw (4).
11 Turn on water supplies. Activate faucet and flush
both HOT and COLD water for 1 minute.
12 Turn OFF faucet and install Aerator. Secure with
included Aerator Wrench. Do not over-tighten.
