Speakman EYESAVER SE-570 Guide

SPEAKMAN®
400 Anchor Mill Rd. New Castle, DE 19720 Phone: [phone] Fax: [phone]
02/01/18 www.speakman.com 92-SE-570-01
SPEAKMAN®
SE-570
Installation, Operation & Maintenance Instructions
EYESAVER® EYEWASH
DESCRIPTION
Deck mounted emergency eyewash. Supplied with a ¼ turn ceramic PERFECT® valve that is activated when
the eyewash is rotated 90° over an open sink. Unit is supplied with an adjustable flow regulator. Aerated
spray outlets with individual flow restrictor, and flip-off dust covers. Unit mounts on counter tops up to
2-1/4” thick.
SPECIFICATIONS
SPRAY HEADS: (2) AERATED YELLOW ABS SPRAY OUTLET, SPRAY FACE, AND DUST COVERS
VALVE: ¼ TURN CERAMIC PERFECT VALVE®
FLOW REGULATOR: BRASS, CHROME-PLATED
INLET: 1/2" NPT MALE
SHIPPING WEIGHT: 6 LB
EMERGENCY SIGN: 7-7/8” X 7-7/8” PLASTIC WALL SIGN
Options:
ILS In-Line Strainer LH Left-Hand Operation
INSTALLATION
NOTE: This unit should be connected to an uninterrupted
source of potable water, with a minimum flowing pressure
of 15 PSI and a maximum static pressure of 80 PSI.
Review drawing (as shown on other side) to assure proper installation. At desired location, use the supplied
deck plate to mark mounting holes. Drill the 1” diameter hole through the countertop (2-1/4” thick max.), and
drill the 1/4” diameter hole a minimum of 5/16” deep. Be sure the holes are drilled as straight as possible.
Place eyewash through drilled holes making sure the threaded shank & ¼” stop screw fit with no interference,
and that the eyewash is resting flat on the deck plate. Attach eyewash to countertop using the supplied
hardware. Install the supplied volume regulator (use thread sealant on all joints), making sure the adjustment
screw is facing in a direction that is easily accessible for later adjustment. Connect a water supply to unit that
is a 1/2” minimum uninterrupted source of potable water (use pipe sealant on connection). Failure to use
potable water can result in emergency units producing impure or contaminated water causing possible
further injury.
OPERATION
Be sure unit is above sink or drain before activating. The eyewash is activated by grasping the eyewash and
rotating it 90° to the full open position. Once the unit is activated, water will discharge from the spray outlets
until the eyewash is manually rotated back to the off position.
TESTING PROGRAM
The American National Standards Institute (ANSI) states that all safety emergency equipment shall be
activated on a weekly basis to flush the line and verify proper operation. Speakman Company furnishes a
testing record tag (91-0635) with each unit. On this tag the date of inspection and the inspectors initials
should be noted.

SPEAKMAN®
400 Anchor Mill Rd. New Castle, DE 19720 Phone: [phone] Fax: [phone]
02/01/18 www.speakman.com 92-SE-570-01
MAINTENANCE
The valve and the eyewash aerators are the only portions of the unit that may require maintenance. Should
you need parts to repair this unit, please reference the parts listing below for correct part numbers. Before
any maintenance is done be sure to shut the water supply off.
ROUGH-IN
FLOW DATA
EYEWASH:
FLOW PRESSURE PSI (BAR) 15 (1)
FLOW RATE GPM (LPM) 3 (11)
REPLACEMENT/REPAIR PARTS
ITEM PART/GROUP # DESCRIPTION
1 RPG05-0714 Aerated Bull Horn Assembly
2 31-0546 Eyewash Arm
3 RPG05-0603 PERFECT Valve (Not Shown)
3 RPG05-0604 PERFECT Valve- Left Hand (Not Shown)
4 45-0678 Flat Steel Washer
5 01-0412-MO ½” – 14 NPSM Locknut
6 G20-1940-RCP ½” Volume Regulator
7 RPG05-1177 Aerator Replacement Group (6 Each)
8 RPG38-0379 Aerated Sprayhead Assembly (4 Each)
9 RPG07-0104 Flip Top Dust Cap Replacement (20 Per Bag)
WARNING: Use only genuine Speakman parts when repairing or replacing components.
To order parts call 1-800-537-2107.
Note: All units meet existing ANSI Z358.1 Standards and OSHA Rules. Product
improvements may cause specification and dimensional changes without notice.
Note: All units meet existing ANSI Z358.1 Standards and OSHA Rules. Product
improvements may cause specification and dimensional changes without notice.
Note: All units meet existing ANSI Z358.1 Standards and OSHA Rules. Product
improvements may cause specification and dimensional changes without notice.
NOTE: This unit should be connected to an uninterrupted
source of potable water, with a minimum flowing pressure
of 15 PSI and a maximum static pressure of 80 PSI.