Speakman SB-2401 User manual

INSTRUCTIONS FOR MODELS
92-SB-2401-01
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SB-2401
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Adjustable
Wrench
10mm
Wrench
Safety
Glasses
Aerator
Wrench
(included)
Flat Tip
Screwdriver
Additional warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This faucet has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives may damage the finish and
void the product warranty. Please be sure to only use
approved cleaners. Please contact Speakman for any
clarification of acceptable cleaners.
1Make sure Rubber Gasket is inserted properly in
Faucet groove. If not, place Rubber Gasket over
Hoses and align to base of Faucet.
2Place Hoses, one at a time, through hole in
mounting surface. Lower Faucet into position.
NOTE: If installing optional
Deck Plate, slip the Hoses
through the Deck Plate. Then
place Hoses, one at a time,
through hole in mounting
surface. Lower Faucet into
position. Ensure a proper seal
with the Rubber Gasket to the
mounting surface. Make sure
the Deck Plate is properly
aligned to the Faucet.
3From below, install Rubber Washer (1), Metal
Washer (2), and secure with Mounting Nuts (3).
Align Faucet to desired position and wrench
tighten Mounting Nuts (3).
OR OR
4Make connections to water supplies. The inlet
threads of the faucet are 9/16”-24 UNEF and
will accept a 3/8” Compression Fitting. Wrench
Tighten.
Accepts a 3/8”
Compression
Fitting
SUPPLY STOPS NOT INCLUDED
5 Remove Stopper ❶, Flange Nut ❷, and Flange
Washer ❸from Drain Assembly.
6 From beneath, insert Drain Assembly through
drain hole in sink. Attach supplied Flange
Washer ❶or plumber’s putty to the underside of
the Flange ❷. Secure Flange ❷to the Drain
Assembly. Align the Drain Assembly as shown
below.
Align towards faucet.
7 From beneath, secure Rubber Washer ❶, Plastic
Washer ❷, and Mounting Nut ❸. Wrench
tighten.
8 Remove Pivot Nut ❶, from Drain Assembly.
Install Outer Pivot Washer ❷, and Pivot Rod ❸.
Ensure that Inner Pivot Washer ❹is retained in
Drain Assembly. Insert Pivot Rod into Drain
Assembly and install Stopper ❺as non-remov-
able. Secure Pivot Rod to Drain Assembly by
tightening Pivot Nut ❶.
9Place one end of Spring Clip ❶, on Pivot Rod
❷. Insert Pivot Rod ❷through a hole in the
Lift Rod Strap ❸. Secure with Spring Clip ❶.
10 Place Drain into the open position by pressing
downward on the Pivot Rod ❶. Insert Lift Rod ❷
into Strap ❸. Adjust height of Lift Rod ❷, and
tighten Thumb Screw ❹.
11 Additional adjustments can be made to ensure a proper seal between the Drain Stopper ❶ and Drain
Assembly. Remove Pivot Nut ❷, from Drain Assembly. Slide out Pivot Rod Assembly ❸. Remove Drain Stopper
❶. Additional adjustments can be made by either threading in or out the eyelet portion of the Drain Stopper ❶.

12 Turn on water supplies. Activate faucet and flush
both HOT and COLD water for 1 minute.
13 Turn OFF faucet and install Aerator. Secure with
included Aerator Wrench. Do not over-tighten.
SB-2401 REPAIR PARTS SPEAKMAN®
ITEM NO. PART NO. DESCRIPTION
RPG05-1112 CARTRIDGE AND RETAINING NUT
RPG05-1113 1.2 GPM SLIM AERATOR WITH KEY
RPG04-0444-XX (* XX = FINISH) LEVER HANDLE, SET-SCREW, AND INDEX BUTTON
RPG63-0102 20” LONG HOSE (2 PCS) (OUTLET THREAD - 9/16” – 24 UNEF 2B THREAD)
RPG24-0134 DRAIN ASSEMBLY PLUS MOUNTING HARDWARE
MOUNTING HARDWARE GROUP
RPG05-1114
SB-2401 ROUGH-IN DIAGRAM SPEAKMAN®
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS OTHERWISE SPECIFIED.
DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.
MINIMUM DECK
HOLE DIAMETER
THICKNESS
21
8
"
53mm
33
8
"
87mm
8"
203mm
2" MAX
52mm
11
4
"
32mm
(FOR DRAIN CONNECTION)
POP UP DRAIN