Speakman SB-2141 User manual

INSTRUCTIONS FOR MODELS
92-SB-2141-02
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SB-2141
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Phillips
Screwdriver
Adjustable
Wrench
5 Gallon
Bucket
11mm
Wrench
Safety
Glasses
Plumber’s
Putty
Warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This faucet has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives may damage the finish and
void the product warranty. Please be sure to only use
approved cleaners. Please contact Speakman for any
clarification of acceptable cleaners.
1Place the Base Flange (1) and the Washer (1)
over hoses and align to base of Faucet.
NOTE: For single hole sink only.
2Place Hoses, one at a time, thru hole in
mounting surface. Lower Faucet into position.
3Partially thread the screws as shown on the
Mounting Nut.
4From below, install Rubber Washer (1), Metal
Washer (2), and secure with Mounting Nut (3).
Align Faucet to desired position and hand
tighten Mounting Nut (3).
5Position the screws to the front and back. Tighten
the screws with Phillips Screwdriver.
FRONT
BACK
6Make connections to water supplies. The inlet
threads of the faucet are 9/16”-24 UNF and
will accept a 3/8” Compression Fitting.
Wrench Tighten.
Accepts a 3/8”
Compression
Fitting
SUPPLY STOPS NOT INCLUDED
7If water supply is 1/2" Compression, use the
provided adapter and 1/2" IPS faucet
connections (not supplied) ❶or use the supplied
coupling nuts ❸with 3/8” O.D. ball nose risers
(not supplied) ❷. Use wrenches to tighten
connections. Do not over-tighten.
INLET SUPPLIES NOT INCLUDED
8Place the spray hose (exiting from base of
faucet) into a bucket. Turn ON water supplies.
Flush both HOT and COLD water for 1 minute
into the bucket.
9Turn OFF water supplies. Connect the spray
hose to the outlet hose. This is a push to connect
connection. Make sure to push the hose
completely into the outlet fitting.
10 Use the provided screws to install the weight
onto the sprayhead hose. Position the weight
above the bottom of the hose loop. Check for
smooth operation.
11 Turn ON water supplies and check for leaks.

SB-2141 REPAIR PARTS
ITEM NO. PART NO. DESCRIPTION
RPG05-108762 CARTRIDGE
RPG05-108760 SPRAYHEAD ASSEMBLY PC
RPG05-109298 SPRAYHEAD ASSEMBLY BN
RPG05-108763 MOUNTING HARDWARE GROUP
NOTES:
COMPLIANCE:
CONNECTIONS:
ASME A112.18.1/CSA B 125.1
Supply Connection:
1/2-14 NPSM-2A Connection or
9/16"-24 UNF Connection
FLOW DATA:
• 1.8 gpm (6.8L/min)
213
16
"
71mm
MAX DECK THICKNESS
25
16
"
58mm
1 1/4" MIN DECK HOLE SIZE
41
2
"
114mm
1/2-14 NPSM-2A
9/16"-24 UNF
91
8
"
232mm
11 1
8
"
283mm
10°
87
8
"
225mm
2"
51mm
MIN. TO WALL
2"
51mm
MIN. TO SINK LEGED
2"
MIN. TO LEDGE
51mm
2"
MIN. TO WALL
51mm
LAVATORY ROUGH-IN
32mm
11
4
"
MIN
SB-2141 ROUGH-IN DIAGRAM
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS
OTHERWISE SPECIFIED. DIMENSIONS SUBJECT TO
CHANGE WITHOUT NOTICE.