Speakman SEF-1800 EYESAVER User manual

9/06 rev.7
Page 1 of 6 92-2140
SPEAKMAN SAFETY PRODUCTS
Installation, Maintenance & Operation Instructions
SEF-1800 EYESAVER®FAUCET
DESCRIPTION
The SEF-1800 Eyesaver®faucet combines a gooseneck faucet with an independently operated eyewash.
The faucet features ¼ turn Speakman Ceramic Perfect®Valves while the eyewash offers twin aerated
sprays and flip top dust covers.
SPECIFICATIONS
OPERATION: Eyewash and faucet operate independently of each other
SUPPLY: ½” male connections for hot and cold inlets
WIDESPREAD VALVES: Perfect® valves with 1/4 turn ceramic cartridges covered by a 25 year
warranty
FINISH: Chrome plated brass
FAUCET HANDLES: Vandal-resistant 4” wrist handles with color- coded indexes
EYEWASH ACTIVATION: Pull handle with graphics
EYEWASH SPRAYS: Aerated sprays.
FAUCET FLOW RATE: Autoflo® device controls flow to 2.2 GPM/ 8.3 LPM
EYEWASH FLOW RATE: 2.6 GPM at 30 psi. flowing. See flow data chart for additional information.
COUNTER THICKNESS: Up to 2” thick
CENTER DISTANCE: Adjustable centers of 6” to 12”
PRESSURE: 30 psi. minimum flow pressure, 125 psi. maximum static pressure
APPROVALS: Meets ASME A112.18.1, ANSI Z358.1 and CSA B125-98
VACUUM BREAKER (ST option): Approved by ASSE, UPC and CSA. Meets the ANSI/ASSE 1035
standard for “Laboratory Faucet Vacuum Breakers”, CSA B64.8 and UPC.
SHIPPING WEIGHT: 10 LBS.
Notes: All dimensions are in inches
(millimeters) unless otherwise
specified and are subject to change.
IMPORTANT: The supply line for plumbed units shall provide an uninterruptible supply of flushing fluid at
a minimum of 30 psi . of flow pressure. If shut off valve are installed in the supply line of the eyewash for
maintenance purposes, provisions shall be made to prevent unauthorized shut off.

9/06 rev.7
Page 2 of 6 92-2140
OPTIONS
FLOW DATA
◊BOCA – Vandal-Resistant 0.5 gpm Flow Control ◊6WH – 6” Wrist Handles
◊D75 – Diamond 75 Escutcheons ◊LF – Laminar Flow Outlet 2.2gpm
◊ST – Serrated Tip with Vacuum Breaker
(see figure) ◊8 – 8” Gooseneck Depth (see figure)
Flowing Pressure- psi.
(BAR) 30 (2.07) 40 (2.76) 50 (3.45) 60 (4.14) 70 (4.83) 80 (5.52)
Flow Rate- gpm
(LPM) 2.6 (9.8) 2.9 (11) 3.0 (11.4) 2.8 (10.6) 2.8 (10.6) 3.0 (11.4)
Distance Eyewash ins.
Plume, ’A’ - (cm.) 13 (33.0) 14-1/2 (36.8) 15 (38.1) 15 (38.1) 15 (38.1) 16 (40.6)

9/06 rev.7
Page 3 of 6 92-2140
PACKING LIST
Item Description Qty. Item Description Qty.
1 Valve Body Assembly, Hot side 1 9 Aerator 1
1b Valve Body Assembly, Cold side 1 10 Handle and Trim package for – D75
option, (replaces item 2 & 3) 2
2 Trim Package 2 11
Handle package for – 6WH option,
(replaces item 3) 2
3 Handle Package 2 12
Serrated Tip and Vacuum Breaker for
–ST option, (replaces item 9) 1
4 Goosneck Assembly 1 13
.5 gpm aerator for – BOCA option,
Item not shown (replaces item 9) 1
5 Washer Bag Group 1 14 Laminar flow outlet for – LF option,
Item not shown (replaces item #9) 1
6 Valve Body Hose 2
7 Adapter Tee Group 1
8 ½” Hose 1

9/06 rev.7
Page 4 of 6 92-2140
INSTALLATION
Step 1: Valve Body Mounting- The valve bodies are marked
with red marker for the hot supply and blue marker for the cold
supply.
a. Screw locknuts down onto the valve body assemblies.
b. Place the cup washers onto valve bodies.
c. Working from below the sink, insert the valve body
assemblies through holes in sink or countertop. From
above sink, place rubber washers onto the valve bodies.
d. Next, screw flange nuts onto valve bodies with flat side
up, flush with top of valve bodies and tighten flange nut
using the set-screw.
e. From under sink, screw locknuts up hand tight. Position
f. bodies so that outlets are accessible and wrench tighten locknuts
g. while holding bodies in place.
Step 2: Gooseneck Eyewash Mounting-
a. Slip the base washer onto the gooseneck eyewash and slip
through the center hole of the sink or countertop.
b. The gooseneck eyewash swivels through 200° of rotation.
Position the base of the gooseneck eyewash so the setscrew
hole in the base is pointing towards the back of the sink or
countertop. Note- For rigid gooseneck, position the
gooseneck and tighten the setscrew in the mounting base.
From below the sink slip the cup washer onto the shank and
use the nut to tighten the assembly down onto the sink or
countertop.
c. Important- Next insert the rubber seal into the adapter and
screw the adapter onto the shank of the gooseneck eyewash
until it bottoms out (Tape may be applied to the shank). If the
adapter needs to be positioned for hose attachment, it can be
backed off up to a maximum of 1 / 2 turn.
d. Apply tape or sealant and connect the tee and nipple so that
the tee outlets are accessible.
Step 3: Hose Connections-
a. Screw valve body hoses onto the side outlets of
the valve bodies and tighten. Screw the other
end of the hoses onto base adapter.
b. Apply tape to the male end of the ½” hose and
connect to the side port of the tee as shown.
Attach the other end to the cold side valve body
inlet and tighten.
c. Connect the vertical inlet of the tee to the cold
water inlet supply.
d. Connect the hot water supply line to the inlet of
the hot water valve body and tighten the

9/06 rev.7
Page 5 of 6 92-2140
coupling nut.
Step 4: Trim Package-
a. From above sink, place the trim flange over the valve spindles.
b. Screw trim collar onto the valve body and tighten. The flange
should be secure at this point. If not, back off the flange nut that
was assembled in step 1 and reassemble the trim.
c. Slip sleeves onto valve spindles.
d. Position the handles and secure using the lock washer and screw.
e. Position the red index button on the handle for the hot water valve
and press into place. Position the blue index button on the handle
for the cold water valve and press into place.
Step 5: Unit Flushing-
a. After the assembly is complete, turn the hot and cold
water supplies on and check for leaks.
b. Activate the faucet to flush both the hot and cold sides
of fixture. Check all connections for leaks.
c. Install the aerator into the faucet outlet.
d. At this time activate faucet and then activate the
eyewash by pulling the handle and assure proper spray
formation and no leaks.
ALTERNATE INSTALLATION FOR
DEDICATED TEPID WATER SUPPLY
The unit is designed so the eyewash has a
dedicated supply line. This allows the eyewash to
have a tepid water supply. For this type of
installation, follow the installation instructions but
do not assemble the tee, nipple and ½” hose
(Steps 2d, 3b and 3c). Attach the tepid water
supply to the center adapter as shown in the figure
and your cold water supply to the cold valve body.
ANSI Z358.1-1998 requires that the delivered
flushing fluid temperature shall be tepid. Also, in
circumstances where chemical reaction is
accelerated by flushing fluid temperature, a
medical advisor should be consulted for the
optimum temperature of each application.
IMPORTANT: The supply line for plumbed
eyewash units shall provide an uninterruptible
supply of flushing fluid at a minimum of 30 psi. of
flow pressure. If shut off valve is installed in the supply
line of the eyewash for maintenance purposes,
provisions shall be made to prevent unauthorized shut off.

9/06 rev.7
Page 6 of 6 92-2140
OPERATION
Faucet-Simply rotate the handles to operate the lavatory faucet.
Eyewash- The eyewash is activated by pulling the handle out. Once the eyewash is activated, the
eyewash caps will flip off and water will come out of the aerated spray heads. The eyewash will
continually discharge water until the handle is manually pushed back into the off position.
The flow of the individual spray heads is controlled by built-in flow controls. Each spray assembly is
tested and aligned in the factory.
TESTING PROGRAM
ANSI Z358.1 requires that all emergency equipment shall be tested weekly to verify proper operation
and inspected annually to assure conformance with ANSI Z358.1 - 1998 requirement.
MAINTENANCE (CARE and CLEANING)
End body valves are washer-less and require no routine maintenance. The gleaming finish of your
SPEAKMAN Eyesaver®faucet can be cleaned by using mild soap and warm water. Rinse thoroughly
and dry immediately with a soft, clean cloth for best results.
REPAIR PARTS LISTING
Part or
Group Number Description Refer to Packing List Figure
RPG04-0316-PC 4” wrist handle group with screw and index buttons Item 3
RPG10-0070-PC Collar and flange Item 2
RPG20-1895 End Body Assembly (red) with mounting hardware Item 1
(hot supply)
RPG20-1894 End Body Assembly (blue) with mounting hardware Item 1b
(cold supply)
RPG05-0534 Perfect valve cartridge only (red) Perfect valve cartridge
(hot supply)
RPG05-0535 Perfect valve cartridge only (blue) Perfect valve Cartridge
(cold supply)
RPG38-0388 Yellow spray head and aerator repair parts assembly Part of item 4
RPG49-0003 Repair parts for internal seals of the gooseneck eyewash Not shown
G05-0724-PC Faucet 2.2 gpm aerator Item 9
RPG04-0366 Eyewash handle with yellow text and set screw Part of item 4

11/03 rev.1
92-2450
Page 1 of 2
SPEAKMAN SAFETY PRODUCTS
Replacement Instructions for seals on the
SEF-1800 EYESAVER®FAUCET
To service the seals for your SEF-1800, determine the issue to be addressed. The
figure below shows different areas and indicates which seal to replace if needed. Shut
off water supply before beginning any work on the SEF-1800 unit.
Area Eyewash Valve Faucet Valve Replace Seals Disassembly Instructions
A Off Off 2c, 4 Follow Step 3 for seal 2c.
Follow Step 4 for seal 4.
A On Off 2b Follow Step 1
B On Off 2a Follow Step 1 & Step 2
C Off On 2b Follow Step 1
C Off Off 1 Follow Step 1
D Off On 3a Follow Step 1
E Off On 3b Follow Step 3
F Off On 5 Follow Step 3
G Off On 6 Follow Step 4
Disassembly Instructions:
Step 1- While holding the body, back off the nut slightly and
then unscrew the body all the way off. Replace the
necessary seals. To reassemble, screw the body back on
the tube until it cannot be screwed on any further. At this
point, back off the body to position the spray heads vertical,
then tighten the nut onto the body securing it in place.
Step 2- To gain access to seal 2a, while the body is
disassembled from Step 1, pull the handle out. This will
expose a setscrew on the bottom. Remove the setscrew and
push the spindle out. Replace the necessary o-ring. Put the
spindle back in the body and attach the handle with the
setscrew.
Step 3- Take the setscrew out of the back of the base.
Unscrew the swivel nut and pull the tube out to get access to
the seals. Replace the necessary seals. To reassemble,
place the tube back into the base and screw down the swivel
nut. Screw the setscrew into the back of the base. Do not
tighten the setscrew. The tube should freely rotate.
Step 4- Disconnect any hoses to the tee. Unscrew the tee and replace any necessary
seals. Screw the tee back on tight and connect the hoses.
After reassembly of the unit, with the valve in the off position, turn the water service
back on and check for leaks. Verify proper operation of the eyewash and faucet.

11/03 rev.1
92-2450
Page 2 of 2