Speakman Symmons CPT-1000-UNI User manual

INSTRUCTIONS FOR MODELS
NEED HELP?
92-CPT-1000-UNI-S-R2
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
CPT-1000-UNI
CPT-1300-UNI
Symmons Installation
TOOLS AND SUPPLIES
IMPORTANT
SAFETY TIPS
Cover your drain to prevent loss of parts. Be sure to
always wear proper eye protection.
MAINTENANCE
Your new Valve Trim is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. Avoid
abrasive cleaners, steel wool, and harsh chemicals as
these will dull the finish and void your warranty.
WARRANTY
Additional warranty information can be found at:
www.speakman.com
Flat Tip
Screwdriver
Phillips
Screwdriver
Measuring
Tape
• Circular Trim Package shown for reference. While
the appearance of your trim may be different, the
installation steps are the same.
• This Trim Package is intended to only mount to the
following Symmons valves. Please verify the model of
your valve prior to installation.
*NOT FOR USE WITH DIVERTER/VOLUME CONTROL MODELS
SYMMONS® Temptrol®
4000-BODY
4000-X-BODY
46-2-X-BODY
• Verify that existing Valve is installed
correctly per manufacturers instructions. If
valve is not installed correctly, installation of
the Universal Valve Trim may not be possible.
1Clean front surface of wall. Verify that Symmons Valve Stops (4) are in the “Open” position by
turning counter-clockwise. Install Valve Mounting Plate (1) to existing Symmons Valve, using the
8-32 x 1-3/8” screws (2), and Washers (3) provided. Take care to not over tighten mounting
screws or damage may occur.
NOTE: The back surface of the Valve Mounting Plate Assembly (1) should sit flush against the wall when
installed correctly.
2
NOTE: The back surface of the Valve Mounting Plate Assembly (1) should sit flush against the wall when
installed correctly.
Secure the Wall Mounting Plate (1) to the Valve Mounting Plate (2) using the 8-32 X 5/8” Screws
(3) provided.

3
MEASURE
The Universal Valve Trim kit includes two (2) Spindle Adapters that allow for both shallow and
deep valve mount installations. Measure the distance between the front lip of the Wall Mounting
Plate and the end of the Symmons Spindle as shown below to determine which Spindle Adapter is
to be used.
• If the measurement falls between 9/16” to 1-1/16”, then Spline Adapter marked “B” is to
be used for installation.
• If the measurement falls between 1-1/16” to 1-9/16”, then Spline Adapter marked “A” is to
be used for installation.
A
B
4
VERTICAL
LINE
Confirm that the Valve is in the off position. Retrieve Spline Adapter to be used as determined in
Step 3. Insert Spline Adapter (1) over Symmons spindle (2). One set of splines on the adapter must
be oriented perfectly vertical when installed, as shown below. Secure the Spline Adapter with the
8-32 X 7/8” Screw (3) provided.
5
RED
BLUE
Orient the Decorative Wall Plate (1) as shown below and insert the RED index button into the top
hole of the Wall Plate, and the BLUE index button into the lower hole. Slide Wall Plate Assembly
over Wall Mounting Plate (2).
6Orient the Handle Assembly in a vertical position as shown below. Guide Handle Assembly onto
the Spline Adapter (3). While holding the Handle (1) stationary in the vertical position, thread the
Handle Escutcheon (2) onto the Wall Mounting Plate (4). Hand tighten until snug.
NOTE: This style of Valve uses a “Compression Stop”. After Handle Assembly
installation, rotate Handle clockwise to achieve full compression and closure of Valve.
If the Handle does not rest in a vertical position after full compression, repeat Steps 4
and 6 for proper Handle alignment.

REPAIR PARTS
•RPG10-0116
ROUGH-IN DIMENSIONS: CPT-1000-UNI
•Dimensions are subject to change without notice.
71
4
"
186mm
2"
51mm
41
2
"
114mm
31
2
"
89mm
1"
25mm
ROUGH-IN DIMENSIONS: CPT-1300-UNI
•Dimensions are subject to change without notice.
71
4
"
186mm
71
4
"
186mm
21
4
"
56mm
31
2
"
89mm
45
8
"
117mm
11
8
"
28mm