Speakman SB-1041 User manual

INSTRUCTIONS FOR MODELS
92-SB-1041-03
For additional assistance or service please contact:
SPEAKMAN®Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
SB-1041
HELPFUL TOOLS & SUPPLIES:
TOOLS AND SUPPLIES
Adjustable
Wrench
11mm
Wrench
Safety
Glasses
Plumber’s
Putty
Warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This faucet has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives may damage the finish and
void the product warranty. Please be sure to only use
approved cleaners. Please contact Speakman for any
clarification of acceptable cleaners.
1Place Rubber Gasket over Hoses and align to
base of Faucet.
2Place Hoses, one at a time, thru hole in
mounting surface. Lower Faucet into position.
3From below, install Rubber Washer (1), Metal
Washer (2), and secure with Mounting Nut (3).
Align Faucet to desired position and wrench
tighten Mounting Nut (3).
OR
4Make connections to water supplies. The inlet
threads of the faucet are 9/16”-24 UNF and
will accept a 3/8” Compression Fitting.
Wrench Tighten.
Accepts a 3/8”
Compression
Fitting
SUPPLY STOPS NOT INCLUDED
5If water supply is 1/2" Compression, use the
provided adapter and 1/2" IPS faucet
connections (not supplied) ❶or use the supplied
coupling nuts ❸with 3/8” O.D. ball nose risers
(not supplied) ❷. Use wrenches to tighten
connections. Do not over-tighten.
INLET SUPPLIES NOT INCLUDED
6Remove Aerator from faucet.
7Turn on water supplies. Activate faucet and flush
both HOT and COLD water for 1 minute.
8Turn OFF faucet and re-install Aerator. Hand
Tighten.

SB-1041 REPAIR PARTS
ITEM NO. PART NO. DESCRIPTION
RPG05-0822 CARTRIDGE
RPG05-108748 1.5 GPM AERATOR ASSEMBLY
RPG05-109424 MOUNTING HARDWARE GROUP
NOTES:
COMPLIANCE:
CONNECTIONS:
ASME A112.18.1/CSA B 125.1
Supply Connection:
1/2-14 NPSM-2A Connection or
9/16"-24 UNF Connection
FLOW DATA:
• 1.5gpm (5.7 L/min)
41
8
"
105mm
21
8
"
54mm
1 1/4" MIN DECK HOLE SIZE
33
16
"
82mm
MAX DECK
THICKNESS
1/2-14 NPSM-2A
9/16"-24 UNF
61
2
"
166mm
5"
127mm
73
4
"
197mm
15°
2"
[51mm]
MIN. TO WALL
2"
[51mm]
MIN. TO SINK LEDGE
2"
MIN. TO LEDGE
51mm
2"
MIN. TO WALL
51mm
LAVATORY ROUGH-IN
32mm
11
4
"
MIN
SB-1041 ROUGH-IN DIAGRAM
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) UNLESS
OTHERWISE SPECIFIED. DIMENSIONS SUBJECT TO
CHANGE WITHOUT NOTICE.