Speco O2P12X User manual

Quick Start Guide
12X PTZ IP Camera
O2P12X
Version 1.1.1

i
Table of Contents
1 EVICE CHECK ........................................................................................................... 1
1.1 Installation Requirements ...................................................................................................................... 1
1.2 Check Accessories ................................................................................................................................... 1
2 WALL MOUNT INSTALLATION .................................................................................... 2
2.1 Component Installation .......................................................................................................................... 2
2.2 Wall Mount Installation Steps ................................................................................................................ 2
2.2.1 Installation Environments .................................................................................................................... 2
2.2.2 Installation Steps ................................................................................................................................. 2
3 IP SCANNER .............................................................................................................. 5
3.1 Overview ................................................................................................................................................ 5
3.2 Operation ............................................................................................................................................... 5
4 WEB OPERATION ...................................................................................................... 6
4.1 Login and Main Interface ........................................................................................................................ 6
5 APPEN IX Ⅰ
ⅠⅠ
Ⅰ SURGE PROTECTION ............................................................................... 7
6 APPEN IX Ⅱ
ⅡⅡ
Ⅱ 12V C WIRE GAUGE AN TRANSMISSION ISTANCE REFERENCE ........... 8
7 APPEN IX Ⅲ
ⅢⅢ
Ⅲ WIRE GAUGE REFERENCE ...................................................................... 9

ii
Welcome
Thank you for purchasing this Network camera!
This manual is designed to e a reference tool for your system.
Please read this manual carefully efore operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical
Support.

iii
Important Safeguards and Warnings
1．
．．
．Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: o not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must be grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2．
．．
．Environment
Heavy stress, violent vi ration or exposure to water is not allowed during transportation,
storage and installation.
This product should e installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not lock any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and aily Maintenance
Please shut down the device and then unplug the power ca le efore you egin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a lower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean the
device.
Please use a professional optical cleaning method to clean the enclosure. Improper
enclosure cleaning (such as using cloth) may result in poor IR functionality and/or IR
reflection.
The grounding holes of the product are recommended to e grounded to further enhance
the relia ility of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:
Stained with dirt
Use oil-free soft rush or hair dryer to remove it gently.
Stained with grease or fingerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens

iv
center outward. Change the cloth and wipe several times if it is not clean enough.
Warning
This camera should e installed y qualified personnel only.
All the examination and repair work should e done y qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may e modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring any
o ligation.
Speco Technologies is not lia le for any loss caused y improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Keep the package material in case the camera needs to e sent ack for service or repair.
Contact your rep or Speco customer service department immediately if something is roken
or missing in the package.

1
1evice Check
1.1 Installation Requirements
Basic Requirement
All installation and operation here should conform to your local electrical safety codes.
Before installation, please open the package and make sure all components are included.
Please make sure the speed dome installation environment can meet your requirement.
If there is special requirement, please contact your local dealer for more information.
We assume no lia ility or responsi ility for all the fires or electrical shock caused y
improper handling or installation.
1.2 Check Accessories
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is roken
or missing in the package.
Accessory Name Amount
Network Camera Unit 1
Quick Start Guide 1
Wall Mounting Bracket 1
Installation Accessories Bag 1
CD
1

2
2Wall Mount Installation
2.1 Component Installation
The wall mount racket and outdoor speed dome are shown in Figure 2-1.
Figure 2-1
2.2 Wall Mount Installation Steps
2.2.1 Installation Environments
The wall mount speed dome can e installed on a hard surface wall in indoor or outdoor
environments. Before the installation, please make sure:
The wall is thick enough to install the expansion olt.
The wall can at least sustain the 8x weight of the speed dome, racket and the
accessories.
2.2.2 Installation Steps
1) Drill a hole of 50mm diameter for the ca le exit in the installation wall.
2) In Figure 2-2, connect the adapter lock to the internal thread of the wall mount
racket, until it reaches the end and then fix the set screw. Pull the intelligent
speed dome composite ca le through the adapter lock and pull it out of the other
end of the wall mount racket. Line up the hook at the top of the external
enclosure to the inside hole of the adapter lock and then push it to the end, and
then secure the three screws of the adapter lock firmly. Please note this step is
very important. Please make sure the screws are firm, to reduce the risk of the
camera falling

3
Figure 2-2
3) Drill holes in the wall according to the installation holes at the ottom of the wall
mount racket. Please make sure the ca le exit of the racket is facing the round
hole on the wall. Connect the ca le and then pull it through the hole in the wall.
Use four hex screws and flat washer to secure the racket on the wall. See Figure
2-3.
Figure 2-3

4
Now the installation is complete. See Figure 2-4.
Figure 2-4

3IP Scanner
3.1 Overview
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same su net can e discovered.
3.2 Operation
Open up IP Scanner.
Figure 3-1
In the device list, you can view the IP address, model num er, and MAC address
device. Select the applica le device and dou le click to open up the we viewer.
5
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same su net can e discovered.
In the device list, you can view the IP address, model num er, and MAC address
device. Select the applica le device and dou le click to open up the we viewer.
Figure 3-1 IP Scanner
In the device list, you can view the IP address, model num er, and MAC address
of each
device. Select the applica le device and dou le click to open up the we viewer.