Speco HTFB2TM User manual

INSTRUCTION
MANUAL
2MP Flexible Intensier Technology
TVI Motorized Zoom Focus Camera
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation. Rev. 02/01/2017
HTFB2TM
(Bullet Camera)
HTFD2TM
(Dome Camera)

Contents
- 2 -
◑
Contents...................................................... 2
◑
Precautions ................................................. 3, 4
◑
Safety Instructions ...................................... 5
◑
Package Contents....................................... 6
◑
Camera Installation ..................................... 7-10
◑
Lens Adjustment ......................................... 11
◑
Specications.............................................. 12,13
◑
Camera Dimension ..................................... 14
◑
Features...................................................... 15
◑
OSD Menu Details ...................................... 16- 30
◑
Trouble Shooting......................................... 31

- 3 -
Precautions
Do not install the camera in
extreme temperature conditions.
Do not touch the front lens of the
camera.
Never keep the camera pointed
directly at strong light.
Do not expose the camera to
radioactivity.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or subject
it to physical shocks.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially careful to
provide ventilation when operating under
high temperatures.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
It can cause malfunctions to occur. If exposed to radioactivity the CCD
will fail.
Severe lighting change or flicker can
cause the camera to work improperly.
Housing damage can compromise
weatherproof ratings.
NOTE
* If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
* please check that the power satisfies the normal specification before
connecting the camera.

- 4 -
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION : To prevent electric shock and risk of fire hazards:
ō Do NOT use power sources other than those specified.
WARNING - To prevent electric shock and risk of fire hazards:
୛Do NOT use power sources other than that specified.
୛Do NOT expose this appliance to rain or moisture.
In USA and Canada, Use Class 2 Power Supply Only

- 5 -
Safety Instructions
Precautions for use
Please handle this camera carefully :
◑ This camera should be installed by qualied personnel only
◑There are no user serviceable parts inside
◑Do not disassemble this camera other than to make initial adjustments
◑Use a UL approved regulated 24 volt AC or 12 volt DC power supply
◑
Use appropriate low voltage power cable to prevent re or electrical shock
◑
Please insure that your installation area can support the weight of the camera
◑Do not use a strong or abrasive detergent when cleaning the camera
◑Do not install near cooling or heating device

- 6 -
Package Contents
Please make sure that the following items are included in the Package:
1) HTFB2TM
• 1 Video Test Connector, Power Jack
• 1 Focus Adjustment
• 1 Bracket Base
• 1 Wrench
• Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws M5x10
2) HTFD2TM
• 1 Video Test Connector, Power Jack
• 1 Chameleon Cover
• 1 Wrench
• Set Screw
- 3 Tapping Screws 4x40
- 1 Hexagon Socket Screw M4x8

- 7 -
CAMERA INSTALLATION
6
CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 500mA)
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
3. CONNECT VIDEO CABLE
1) WHEN USING IT AS ANALOG OUTPUT,
CONNECT YELLOW COLOR BNC CABLE TO THE BNC JACK.
2) WHEN USING IT AS TVI OUTPUT,
CONNECT BLACK COLOR BNC CABLE TO THE BNC JACK.
DC 12V Power Supply
Power In put :R ED
Center : (+)
C V B S
T V I
LBACK:(-)
RED(+)
4. CONNECT RS-485 CABLE
- CONNECT 2 WIRE CABLE TO THE 485 PORT AS BELOW.
ORANGE (+)
WHITE (-)
Power Supply
AC 24V

- 8 -
CAMERA INSTALLATION
Compatibility
1) HTFB2TM
2) HTFD2TM
3.90” 8.56”
4.80”
2.95”
3.01”
CVCJBB INTJBS INTCM
CVCJBD INTPMDFM INTCMINTWM

CAMERA INSTALLATION
- 9 -
1. HTFB2TM
WALL
SCREW M5x10, HEXAGON SOCKET , SUS, BK, 4EA
BRACKET ASSYEMBLY
SCREW TS T1, 4X25, TH, SUS, 4EA

CAMERA INSTALLATION
- 10 -
2. HTFD2TM
MACHINE SCREW 4X15, 3EA
LED VANDAL DOME
COVER

- 11 -
1. HTFB2TM
LENS ADJUSTMENT
Open the cap
VIDEO TEST
SET UP
LED LEVEL

- 12 -
1/2.9 Inch SONY 2Mega CMOS Sensor
2001 (H) X 1121 (V)
1985 (H) X 1105 (V)
1920X1080(1080p@30f / 1080p@25f)
1280X720_CROP(720p@60f / 720p@50f)
1280X720_CROP(720p@30f / 720p@25f)
Progressive Scan
50 dB
1.0Vp-p Composite. 75 Ohms / 1.0Vp-p TVI(Transport Video Interface) 75 Ohms
0.001 Lux @ F1.4(Sens-Up X32)
AUTO / Manual(1/25,1/30Sec ~ 1/30000Sec) / FLICKER
0
0
ON / OFF (Low,Middle,High) (15 Fram)
O(OFF/LOW/MIDDLE/HIGH)
Auto / Intensifier
AUTO/AWB/AWC-SET/MANUAL
0
x2 ~ x32
ON / OFF (4 Area)
3DNR (OFF/LOW/MIDDLE/HIGH)
O (AUTO/MANUAL)
0 ~ 20
0~20(Level Adjustable)
ON / OFF (16 Area)
MIRROR,V-FLIP
Image Sensor
Pixels - total
Pixels - Effective
Resolution
Scanning System
S/N Ratio
Video Output
Minimum Illumination
Shutter Speed
BLC
HSBLC
WDR(Wide Dynamic Range)
ACE(D-WDR)
(Adaptive Contrast Enhancement)
Day&Night
White Balance
Smart-IR
Sense-Up
Motion
Digital Noise Reduction
De-Fog
brightness
AGC
Privacy
Mirror
0~20(Level Adjustable)Sharpness
AUTO DETECTDefect
0Coaxial Communication (UTC)
ENG/KOR/CHN/CHA(S)/JPNLanguage
DUALPower
DC 12V - 550mA±10% AC 24V - 270mA±10% MaxPower Consumption
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Operating Temperature
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Storage Temperature
IUGC3UN
SPECIFICATIONS
HTFB2TM (2.8-12mm)
■
2MP FIT TVI Motorized Zoom Focus Camera
2.8-12mm MFZ Lens

- 13 -
1/2.9 Inch SONY 2Mega CMOS Sensor
2001 (H) X 1121 (V)
1985 (H) X 1105 (V)
1920X1080(1080p@30f / 1080p@25f)
1280X720_CROP(720p@60f / 720p@50f)
1280X720_CROP(720p@30f / 720p@25f)
Progressive Scan
50 dB
1.0Vp-p Composite. 75 Ohms / 1.0Vp-p TVI(Transport Video Interface) 75 Ohms
0.001 Lux @ F1.4(Sens-Up X32)
AUTO / Manual(1/25,1/30Sec ~ 1/30000Sec) / FLICKER
0
0
ON / OFF (Low,Middle,High) (15 Fram)
O(OFF/LOW/MIDDLE/HIGH)
Auto / Intensifier
AUTO/AWB/AWC-SET/MANUAL
0
x2 ~ x32
ON / OFF (4 Area)
3DNR (OFF/LOW/MIDDLE/HIGH)
O (AUTO/MANUAL)
0 ~ 20
0~20(Level Adjustable)
ON / OFF (16 Area)
MIRROR,V-FLIP
Image Sensor
Pixels - total
Pixels - Effective
Resolution
Scanning System
S/N Ratio
Video Output
Minimum Illumination
Shutter Speed
BLC
HSBLC
WDR(Wide Dynamic Range)
ACE(D-WDR)
(Adaptive Contrast Enhancement)
Day&Night
White Balance
Smart-IR
Sense-Up
Motion
Digital Noise Reduction
De-Fog
brightness
AGC
Privacy
Mirror
0~20(Level Adjustable)Sharpness
AUTO DETECTDefect
0Coaxial Communication (UTC)
ENG/KOR/CHN/CHA(S)/JPNLanguage
DUALPower
DC 12V - 550mA±10% AC 24V - 270mA±10% MaxPower Consumption
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Operating Temperature
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Storage Temperature
IUGE3UN
SPECIFICATIONS
HTFD2TM (2.8-12mm)
■
2MP FIT TVI Motorized Zoom Focus Camera
2.8-12mm MFZ Lens

- 14 -
CAMERA DIMENSION
1) HTFB2TM
3.90” 8.56”
4.80”
2.95”
3.01”
2) HTFD2TM
HI-POWER LED
PHOTO SENSOR
CASE
CABLE
HEATER
LENS
3.94”
5.12”
5.12”
3.89”

- 15 -
General Features
●
Transfer Video Interface
The combination of a 2Mega CMOS image sensor and TVI DSP provides an excellent resolution
of TVI picture.
●
3D-DNR
Smart 3DNR prevents the image blurring of moving object and activates only if moving objects
are appearing on the scene.
●
Smart-IR
No saturation image, vivid image in darkness! "TVI" camera makes very sharp video image in
darkness! This technology eliminates saturation of video image of the closer object in darkness
by control of the IR sensitivity. Saturation never happens in our "TVI"cameras, you can enjoy
vivid image in any dark condition!
●
Sens-Up
Despite a limited & low light condition, Sens-Up - Max. x32 helps the viewer to get visible and
clear images.
●
Defog
Defog function “improves” the clarity of images taken in poor conditions such as fog, smoke,
rain or snow.
●
WDR(Only For TVI Output)
A powerful and advanced technology that captures a high resolution picture even where
images appear dark.
●
CVBS(Composite Video Blanking and Sync)
TV system is switchable 'NTSC' or 'PAL' with built-in OSD.
●
Intelligent Function
An extraordinary technology that enables Speco Technologies TVI to become the ultimate
solution by providing intelligent features based on motion detection. It also strengthens crime
prevention and detection.

- 16 -
How to Set Up the camera menu
1. PRESET INDOOR, OUTDOOR, LOWLIGHT, HALLWAY, LOOBY(WDR), ELEVATOR
2. MAIN SETUP
3. EXIT RESET(ONE PUSH)
MENU SETUP DEFAULT SET MENU
1. 2MOTOR AF MODE AUTO, MANUAL
SCANNING HALF, FULL
ONEPUSH ONE PUSH
INITIAL ONE PUSH
RETURN
2. EXPOSURE BRIGHTNESS 0~20
SUTTER AUTO
MANUAL SPEED 60Hz 1/30,1/60,1/120,1/500,1/1000,1/2000,1/4000,1/8000,1/15000,1/30000
50Hz 1/25,1/50,1/100,1/200,1/400,1/800,1/1600,1/3200,1/6400,1/12800,1/25600
RETURN
FLICKER
INTENSIFY OFF, X2, X4, X8, X16, X32
AGC 0~20
RETURN
3. WHITE BAL AUTO
AWB
AWC-SET ON(PUSHING)
MANUAL KELVIN LOW, MIDDLE, HIGH
R-GAIN 0~20
B-GAIN 0~20
RETURN
7. IMAGE SHARPNESS 0~20
GAMMA 0.45, 0.5, 0.55, 0.6, 0.65, 0.7, 0.75
COLOR GAIN 0~20
MIRROR ON / OFF
FLIP ON / OFF
ACE OFF, LOW, MIDDLE, HIGH
DEFOG ON MODE AUTO / MANUAL
4. BACKLIGHT OFF
HLC LEVEL 0~20
MODE ALL DAY, NIGHT ONLY
RETURN
BLC H-POS 0~20
V-POS 0~20
H-SIZE 0~20
V-SIZE 0~20
RETURN
WDR WEIGHT LOW, MIDDLE, HIGH
RETURN
5. SPECO DNR OFF, LOW, MIDDLE, HIGH
6. DAY&NIGHT AUTO SMART IR. 0~20
EXTERN SW HIGH, LOW
DELAY LOW, MIDDLE, HIGH
IR LED ON / OFF
IR ADJUST 0~10 IR OFF:NOT USED
RETURN
INTENSIFIER
●
Setup Menu
MENU

- 17 -
7. IMAGE LEVEL LOW, MIDDLE, HIGH
RETURN
OFF
PRIVACY ON ZONE NUM 0~15
ZOME DISP ON / OFF
H-POS 0~60
V-POS 0~34
H-SIZE 0~60
V-SIZE 0~34
Y LEVEL 0~20
CB LEVEL 0~20
CR LEVEL 0~20
RETURN
OFF
RETURN
9. SYSTEM COM. CAM ID 0~255
BAUDRATE 2400, 4800, 9600, 57600, 115200
RETURN
IMAGE RANGE FULL
COMP
USER OFFSET 0~32
RETURN
FRAME RATE
COLOR SPACE HD-CbCr, YUV, SD-CbCr
CVBS NTSC, PAL
LANGUAGE ENG, CHN, CHN(S), JPA, KOR
COLOR BAR ON / OFF
RESET ON(PUSHING)
RETURN
10. EXIT
8. MOTION ON SENSITIVITY 0~10
WINDOW TONE 0~4
WINDOW ZONE 0~3
WINDOW USE ON / OFF
DET H-POS 0~60
DET V-POS 0~34
DET H-SIZE 0~60
DET V-SIZE 0~34
ALARM ON / OFF
OFF
How to Set Up the camera menu
●
Setup Menu
MENU

- 18 -
2. Move and select the required function using the Up and Down button.
* Move the triangular indicator Up or Down to select the desired feature by pressing
the Up or Down button.
Menu Set Up
Menu items can be selected by using the OSD buttons of the camera.
1. PRESET
1-1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY(WDR) / ELEVATOR.
- Used for a quick and easy setup for the installation environment.
* The Advaned Set Up menu will be displayed on the monitor.
SPECO TECH
1. PRESET
2.MAIN SETUP
3.EXIT
INDOOR
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.EXIT
AUTO
AUTO
OFF
MIDDLE
AUTO
OFF

- 19 -
3. Change menu settings using the Left or Right button.
* Available values or Status are displayed by pressing the Left or Right buttons.
Press the button until desired value / status is displayed.
4. After Changing the setting move the arrow indicator to EXIT and press the
SET button to EXIT.
NOTE
* Move to the available submenu by moving arrow to desired feature.
* Submenu is not available when this symbol displayed “---“.
1. Move the triangular indicator to 2MOTOR using the Up and Down buttons on the Set Up menu
screen.
2. Select the desired lens type by pressing the Left of Right button.
2MOTOR
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.EXIT
AUTO
AUTO
OFF
MIDDLE
AUTO
OFF

- 20 -
◆ AF MODE
- AUTO : Adjust zoom and focus automatically.
- MANUAL : Adjust zoom and focus manually.
◆ SCANNING : HALF / FULL
- HALF : Adjust auto focusing when lens focus fixed. If lens focus is not fixed well, adjust focus manually.
- FULL : Scanning full size of scree and adjust autofocusing.
◆ ONEPUSHAF : If you press OSD button 3~4 seconds, focus will be fixed automatically.
◆ INITIAL : If you press OSD button 3~4 seconds, Lens Initializing start.
1. On the Set Up menu, Select EXPOSURE by using the Up or Down button.
EXPOSURE
1. 2MOTOR
AF MODE
SCANNING
ONEPUSHAF
INITIAL
RETURN
AUTO
HALF
ON
ON
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.EXIT
AUTO
OFF
MIDDLE
AUTO
OFF