Spectrum Industries eLogix 99072 Guide

0192005 Page 1 of 4
Timer Replacement InstructionsTimer Replacement Instructions
??
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Important
Avant d’utiliser ce produit:
• Veillez à lire ce guide
• Respectez les consignes de sécurité et d’utilisation
• Vériez que vous disposez de toutes les pièces
nécessaires à l’installation
Importante
Antes de utilizar este producto:
• Lea este manual
• Cumpla con todas las instrucciones de prevención de
accidentes y operativas
• Revise que todas las partes y las cantidades correctas
estén incluidas
Any parts damaged during shipment must be reported within 5
days of receipt. To report information regarding missing parts or
damage, to purchase parts or accessories, or if you have any
questions, please contact us.
Thank you for purchasing Spectrum products!
Les pièces endommagées pendant le transport doivent faire
l’objet d’un rapport dans les 5 jours de leur réception. Veuillez
prendre contact avec nous si des pièces manquent ou sont
abîmées, si vous avez des questions, ou encore pour acheter
des pièces ou des accessoires.
Merci pour votre achat d’un produit Spectrum!
Si alguna parte se dañó durante el embarque, deberá reportarla
en un lapso de 5 días a partir de la recepción. Para reportar
cualquier información sobre partes faltantes o dañadas, para
adquirirlas o comprar accesorios, o bien, si tiene alguna duda,
póngase en contacto con nosotros.
¡Gracias por adquirir productos Spectrum!
Owner’s Manual
Le manuel du propriétaire
El manual del propietario
VideoVideo
VidéoVidéo
VídeoVídeo
SpecsSpecs
SpécicationsSpécications
EspecicacionesEspecicaciones
800-235-1262800-235-1262
http://www.spectrumfurniture.com
99072 - eLogix™Timer
99073 - Power Switch
99071 - PowerProdigy™Timer
Note: There is no need to remove all the devices from the
cart to complete this swap. Removing 3-4 computing devices
below the timer and unhooking the cables from the cable
management bars is all that is required to provide access.
Installation video available
See www.spectrumfurniture.com

0192005 Page 2 of 4
1. Open cart doors to gain access.
2. Unplug all cords from timer.
3. Pull down on each snap button to release the
timer while pulling timer out of the cart. Figure 1.
1. Remove existing timer
1. From outside cart, slide the timer into the slot
in the side of cart until ‘clicks’ are heard. The
clicks are the snap buttons locking the timer into
place. Figure 2.
2. Plug power cords into timer.
Timer replacement (slide-in style)
Existing backstop plate for
eLogix timer or power switch
(backstop not included)
Note: Backstop not used with
PowerProdigy timers
eLogix
™
Timer
Power switch
2. Install new timer
PowerProdigy
™
Timer
Figure 1
Figure 2
Note: Cord bracket is not included or needed
on the Connect30 or Connect18 / 36.
3. Connect cords
Cord Bracket
Power Cords
Timer
1. Plug cords back into timer. Figure 3.
2. If your cart has a cord bracket, route the cords over the bracket.
Figure 3
Snap button
Timer / power option
Snap button

Front screws
0192005 Page 3 of 4
Timer replacement (older screw-mount style)
Figure 1.1 Figure 1.2
Figure 1.3
Cart wall
Front screws
Figure 2.1
Figure 1.4
Back screws
1. Remove existing timer
2. Install new timer 3. Connect cords
Timer
1. Plug cords back into timer. Figure 3.1.
Figure 3.1
Power Cords
1. Install new timer onto the back screws. Figure 2.1.
2. Install front screws.
3. Tighten all four screws securely.
1. Open the cart power-side door(s), unplug all cords from timer,
and remove the (2) front screws. Figure 1.1.
2. From outside the cart, push the left-side of the timer in. Figure 1.2.
4. Loosen the two back screws approximately three turns. Figure 1.4.3. From inside the cart, pull the timer out. Figure 1.3. If the timer is
hard to pull out, insert a long at screwdriver between the timer and
cart wall to pry loose.

0192005 Page 4 of 4 © 2020 Spectrum Industries Inc., All rights reserved.
Internal side
External side
AUX outlet LED lights Power switch
A B C D IEC AUX
Outlet
Inlet
Outlets
eLogix™Timer
Internal side
External side
A A B B IEC AUX
Outlet
Inlet
Outlets
Power switch
The eLogix™timer charges one half of the devices for 15 minutes,
then charges the second half of the devices for another 15 minutes.
This cycling occurs automatically and is not adjustable. Maximum
charging capacity: 2,880 watts.
Power Switch
The Power Switch provides continuous power to
all power units. Use with lower amp-draw devices.
Maximum charging capacity: 1,440 watts.
Internal side
External side
A B C D IEC AUX
Outlet
Inlet
Outlets
AUX Outlet Reset Power switch
PowerProdigy™Timer
• Smart charging senses current
and distributes power to the
power units requiring it most
• Four timed power unit-dedicated
outlets (labeled A, B, C, D)
controlled by logic board
• Four green LED lights indicate
charging activity status of each
power unit
• Two auxiliary outlets (1 external,
1 internal)
• ETL recognized (certied to 60950-1)
Input: 125V~/12A, 60Hz
Breaker: 15A, 250 VAC
Cycling interval: 15 minutes
Cycling outlets: 4 timed (A, B, C, D) up to 10A
Auxiliary outlets: 1A each (controlled by main power switch)
Power Cord: IEC quick-release (replaceable)
8’ nominal, 14 AWG, 3-wire
Power switch: 15A (externally accessible)
Use with higher amp-draw devices.
Maximum charging capacity: 5,760 watts.
• Four continuous power-unit dedicated outlets (labeled A, B, C, D)
• Two auxiliary outlets (1 external, 1 internal)
• ETL recognized (certied to 60950-1)
Input: 125V~/12A, 60Hz
Breaker: 15A, 250 VAC
Outlets: 4 timed (A, B, C, D) up to 10A
Auxiliary outlets: 1A each (controlled by main power switch)
Power Cord: IEC quick-release (replaceable)
8’ nominal, 14 AWG, 3-wire
Power switch: 15A (externally accessible)
• Two timed power-unit dedicated outlets (labeled A, B)
(up to 10A power output)
• Two green LED lights indicate charging activity status
• One auxiliary outlet (external)
• ETL recognized (certied to 60950-1)
Input: 125V~/12A, 60Hz
Breaker: 15A, 250 VAC
Cycling interval: 15 minutes
Cycling outlets: 4 timed (A, B) up to 10A
Auxiliary outlet: 1A (controlled by main power switch)
Power Cord: IEC quick-release (replaceable)
8’ nominal, 14 AWG, 3-wire
Power switch: 15A (externally accessible)
LED lights