Sper scientific 800101 User manual

I/R Thermometer Gun 8:1
800101, 800102
INSTRUCTION MANUAL
SPER
SCIENTIFIC

2
Contents Page
1. INTRODUCTION ........................................2
2. SAFETY SPECIFICATIONS.......................3
3. DISPLAY AND BUTTON LOCATIONS.......4
4. BATTERY REPLACEMENT .......................5
5. MEASURING PROCEDURE ......................5
6. CLEANING .................................................5
7. NOTES .......................................................6
8. SPECIFICATIONS......................................7
9. WARRANTY ...............................................8
1. INTRODUCTION
Simply hold the IR gun, press the trigger and aim the laser
guide at the target. Temperature results immediately
appear on the display. Features include laser guide, 4-digit
backlit LCD, wide measuring ranges, °C/°F selectable, and
automatic shut off. A 9V battery is included.

3
2. SAFTEY SPECIFICATIONS
Conforms to the following standards.
•EN61326: Electrical equip. for measurement/control/labs.
•IEC61000-4-2: Electrostatic discharge immunity test.
•IEC61000-4-3: Radiated, radio freq. electromagnetic field
immunity test.
•IEC61000-4-8: Power freq. magnetic-field immunity test.
•CFR 1040.10 subchapter J Class II Laser Product
Tests were conducted using a freq. range of 80~1000MHz
with the IR Gun in 3 orientations. The average error for the
3 orientations is ±0.5°C (±1.0°F) at 3V/m throughout the
spectrum. However, between 781~1000MHz at 3V/m, the
IR Gun may not meet its stated accuracy.

4
3@24
2@16
25@20 50@40
75@600
mm
inch 1@8
Distance to Spot: 8:1
3. DISPLAY AND BUTTON LOCATIONS
1. Trigger
2. Laser Guide
3. IR Sensor
4. Battery
5. Low Battery Indicator
6. Laser Guide On/Off Indicator
7. Temperature Display
8. C/F Button
9. Scan/Hold Indicators
10. C/F Indicators
11. Laser On/Off Button

5
4. BATTERY REPLACEMENT
•Replace the battery when the Low Battery Indicator (5)
is displayed.
•Open the battery cover, install a fresh 9V battery and
close the cover. Battery life expectancy is 16 hours.
5. MEASURING PROCEDURE
•Point the IR Gun at the object to be measured.
•Pull and hold the TRIGGER (1) to obtain a continually
updated temperature until the trigger is released.
"SCAN" (9) flashes on the display.
•Press the °C/°F BUTTON (8) to switch temperature
units.
•Press the LASER ON/OFF BUTTON (11) to turn the
LASER GUIDE (2) on or off.
•Release the TRIGGER (1) and last temperature reading
is displayed for approximately 6 seconds before turning
off. "HOLD" (9) is displayed.
6. CLEANING
Clean the lens with compressed air, use a soft brush, or
carefully wipe the surface with a moist cotton swab. Do not
use solvents on the lens. The housing may be cleaned
with mild soapy water on a cloth or sponge.

6
7. NOTES
•Emissivity is the ability of an object to emit or absorb en-
ergy. Your IR Gun measures emitted energy using a
fixed emissivity value of 0.95 (which covers about 90%
of typical applications). When measuring highly reflective
surfaces, apply masking tape to the surface or a paint
that has a 0.95 emissivity. If the object you are measur-
ing is covered with frost, clear the frost to expose the
object's surface before taking the measurement.
•Your IR Gun has an 8:1 Distance-to-Spot ratio.
•The target must be larger than the IR Gun's spot size.
(The smaller the target, the closer you must be to it.)
•Your reading may fluctuate if the IR Gun is moved
during measurement.
•Allow the IR Gun to adjust to the ambient temperature
for 1/2 hour before use for the most accurate results.
•This IR Gun is not intended for medical evaluations.
•Protect the IR Gun from water, physical or electrical
shock, dust, and extreme environments.
•Contains a laser pointer. Keep out of reach of children.

7
8. SPECIFICATIONS
Model 800101 800102
Range -4~605°F
-20~320°C
-4~930°F
-20~500°C
Accuracy
±2% of reading or
±2°C (±3°F) at 25°C
whichever is greater
±2°C (±3°F)
from –20~100°C
(-4~212°F)
±2% from 100~500°C
(212~930°F)
Resolution 0.5°C/F 0.2° C/F
D:S Ratio 8:1
Thermopile 5~14µm
Repeatability ±2°F (±1°C)
Laser Output <1mW Wavelength 630~670 nm
Response Time 500ms
Oper. Temp. 32~122°F (0~50°C) 10~90%RH
Emissivity: Fixed at 0.95
Storage Temp. 14 ~ 140°F (-10 ~ 60°C)
Dimensions 6 x 5 x 2" (150 × 133 × 45mm)
Weight 6 oz (171g)

8
9. WARRANTY
Sper Scientific warrants this product against defects in
materials and workmanship for a period of 5 years from
the date of purchase, and agrees to repair or replace
any defective unit without charge. If your model has
since been discontinued, an equivalent Sper Scientific
product will be substituted if available. This warranty
does not cover damage resulting from accident, misuse,
or abuse of the product. To obtain warranty service,
ship the unit postage prepaid to:
SPER SCIENTIFIC LTD
7720 E Redfield Rd, Suite 7
Scottsdale, AZ 85260 USA
WWW.SPERSCIENTIFIC.COM
[email protected]
The defective unit must be accompanied by a descrip-
tion of the problem and your return address. Register
your product online or return your warranty card within
10 days of purchase.
REV. 3/1/07