Sper scientific 800101 User manual

IR Thermometer Gun
8:1
800101 / 800102

2
CONTENTS
INTRODUCTION.............................. 2
SAFETY SPECIFICATIONS ..................... 3
DISPLAY & BUTTON LOCATIONS ................ 4
MEASURING PROCEDURE..................... 5
CLEANING .................................. 5
BATTERY REPLACEMENT ..................... 5
NOTES ..................................... 6
SPECIFICATIONS............................. 7
WARRANTY ................................. 8
INTRODUCTION
Simply hold the IR gun, press the trigger and aim the
laser guide at the target. Temperature results immediately
appear on the display.
Features include laser guide, 4-digit backlit LCD, wide
measuring ranges, °C/°F selectable, and automatic shut
o󰀨. A 9V battery is included.

3
SAFETY SPECIFICATIONS
Read the following safety information carefully before
attempting to operate or service the IR Gun.
• Only qualied technicians should perform repairs.
• DO NOT submerge the IR Gun in water.
• Protect the IR Gun from water, shock, dust,
and extreme environments.
• The IR Gun may be used to measure body
temperature simply for reference. This unit is
not intended for medical evaluations.
• Dispose of properly.
• Contains a laser pointer. Keep away from children.
Conforms to the following standards.
• EN61326: Electrical equip. for measurement/control/labs.
• IEC61000-4-2: Electrostatic discharge immunity test.
• IEC61000-4-3: Radiated, radio freq. electromagnetic
eld immunity test.
• IEC61000-4-8: Power freq. magnetic-eld immunity test.
• CFR 1040.10 subchapter J Class II Laser Product
Tests were conducted using a freq. range of 80 to 1000MHz
with the IR Gun in 3 orientations. The average error for the
3 orientations is ±0.5°C (±1.0°F) at 3V/m throughout the
spectrum. However, between 781 to 1000MHz at 3V/m, the
IR Gun may not meet its stated accuracy.

4
DISPLAY AND BUTTON LOCATIONS
1. Trigger
2. Laser Guide
3. IR Sensor
4. Battery
5. Low Battery Indicator
6. Laser Guide
On/O󰀨 Indicator
7. Temperature Display
8. C/F Button
9. Scan/Hold Indicators
10. C/F Indicators
11. Laser On/O󰀨 Button
Distance to Spot: 8:1
25:20
mm
inch
50:400
75:600
1:8 2:16 3:24

5
MEASURING PROCEDURE
1. Point the IR Gun at the object to be measured.
2. Pull and hold the TRIGGER to obtain a continually
updated temperature until the trigger is released.
SCAN ashes on the display.
3. Press the °C/°F BUTTON to switch temp units.
4. Press the LASER ON/OFF BUTTON to turn the
LASER GUIDE on or o󰀨.
5. Release the TRIGGER and last temperature reading is
displayed for approximately 6 seconds before turning o󰀨.
HOLD is displayed.
CLEANING
Clean the lens with compressed air, use a soft brush,
or carefully wipe the surface with a moist cotton swab.
Do not use solvents on the lens. The housing may be
cleaned with mild soapy water on a cloth or sponge.
BATTERY REPLACEMENT
1. Replace the battery when the LOW BATTERY
INDICATOR is displayed.
2. Open the battery cover, install a fresh 9V battery and
close the cover. Battery life expectancy is 16 hours.

6
NOTES
• Emissivity is the ability of an object to emit or absorb
energy. Your IR Gun measures emitted energy using a
xed emissivity value of 0.95 (which covers about 90%
of typical applications). When measuring highly reective
surfaces, apply masking tape to the surface or a paint
that has a 0.95 emissivity. If the object you are measuring
is covered with frost, clear the frost to expose the object’s
surface before taking the measurement.
• Your IR Gun has an 8:1 Distance-to-Spot ratio.
• The target must be larger than the IR Gun’s spot size.
(The smaller the target, the closer you must be to it.)
• Your reading may uctuate if the IR Gun is moved during
measurement.
• Allow the IR Gun to adjust to the ambient temperature for
1/2 hour before use for the most accurate results.
• This IR Gun is not intended for medical evaluations.
• Protect the IR Gun from water, physical or electrical
shock, dust, and extreme environments.
• Contains a laser pointer. Keep out of reach of children.

7
Model 800101 800102
Range -4 to 605°F
-20 to 320°C
-4 to 930°F
-20 to 500°C
Accuracy ±2% of reading
or ±2°C (±3°F)
at 25°C
whichever
is greater
±2°C (±3°F) from
–20 to 100°C
(-4 to 212°F)
±2% from
100 to 500°C
(212 to 930°F)
Resolution 0.5°C/F 0.2°C/F
D:S Ratio 8:1
Thermopile 5 to 14μm
Repeatability ±2°F (±1°C)
Laser Output <1mW Wavelength 630 to 670 nm
Response Time 500 ms
Operating Temp. 32 to 122°F (0 to 50°C) 10 to 90% RH
Emissivity Fixed at 0.95
Storage Temp. 14 to 140°F (-10 to 60°C)
Dimensions 6⅛" x 3⅜" x 1¼" (156 x 88 x 32 mm)
Weight 6 oz (170 g)
SPECIFICATIONS

8
WARRANTY
Sper Scientic warrants this product against defects in
materials and workmanship for a period of 5 years from
the date of purchase, and agrees to repair or replace any
defective unit without charge. If your model has since been
discontinued, an equivalent Sper Scientic product will
be substituted if available. This warranty does not cover
damage resulting from accident, misuse, or abuse of the
product. To obtain warranty service, ship the unit postage
prepaid to:
SPER SCIENTIFIC LTD,
8281 E. Evans Rd., Suite 103
Scottsdale, AZ 85260
www.sperscientic.com
The defective unit must be accompanied by a description
of the problem and your return address. Register your
product online at www.sperwarranty.com within 10 days
of purchase.
rev. 1/18/2017