Sport-thieme 203 4528 User manual

Assembly instructions
Sport-Thieme®Handball Goal,
3x2 m, socketed
Art.-Nr.: 203 4528
0218214 · © 2018 Sport-Thieme GmbH
D-38367 Grasleben ·Germany
sport-thieme.com · info @sport-thieme.com
Phone: [phone] · Fax: [phone]

2
Assembly instructions for Art.-Nr. 203 4528
1. Scope of delivery
Please check the following content before assembly.
The following indicated quantities refer to 1 Handball goal. In case of a delivery in pairs we double the
amount correspondingly. Pictured colours of proles are only samples and may dier from delivered proles.
1x Crossbar, prole 80 x 80 mm
2x Upright, prole 80 x 80 mm
1x Hexagon screwdriver SW6, DIN 911, length approx. 470 mm (only for goal in ground sockets, cat.no. 2069)
2x Steel corner joint
8x Steel plate
2x Steel angle
2x Upright cap
Accessories
2x Ground socket, length 300 mm
2x Cap for ground socket
Accessories:
32x Net holder
8x Hexagon socket screw M8 x 50, DIN 931
8x Plug pin
2x Upright cap

3
Assembly instructions for Art.-Nr. 203 4528
2. Assembly of the goal
The following tools are necessary:
- 2 wrench/ring spanners 13 mm
- 1 mallet/hammer
- 1 drill Ø 1.5 mm
- 1 thin screw driver (for net hook xing if necessary)
b) Assembly of steel angles:
Place steel angle on the corner of
crossbar/upright construction and screw
4 hexagon socket screws M8 x 50, DIN
931 through holes of angle and crossbar/
upright construction. Adjust goal corner
and tighten all screws.
a) Assembly of crossbar/uprights:
Lay crossbar and uprights on the ground,
groove facing upwards and mitres joining.
Stick 4 steel plates on steel corner joint
(see 1st picture bottom left). Then stick
crossbar and upright on steel corner joint
(see other bottom pictures).
c) Assembly of caps:
Stick caps in the open ends of uprights
(see picture bottom left). Bore them with
drill 1.5 mm through the holes provided in
the uprights.
Then x plug pins with a hammer/mallet
(see picture bottom right).

4
Assembly instructions for Art.-Nr. 203 4528
3. Assembly of the net
a) The net is not part of the delivery.
Fix net holders at the net rope. Bend open net holders a little and press rope into the holders. We recommend the following
distribution of net holders:
crossbar : 16 pieces
uprights : 8 pieces each
b) After having mounted all net holders x net at the goal construction. Stick net holders in the net hook rail and x them with
a 90 degrees’ rotation. Use a thin screw driver if necessary (please avoid damages at the goal).
c) Dismantling of the net is also done by rotation of the net holders through 90 degrees. Use again a thin screw driver if neces-
sary.
4. Assembly of the ground sockets
a) For handball gates with a size of 3,00 x 2,00 m the distance of the ground sockets
must be 3,08 m (middle socket – middle socket = center distance).
b) Concrete ground sockets according to the sketch. Foundation dimensions: 800 x
800 x 800 mm.
c) Do not apply an acceleration mixture or antifreeze during as these adhesives may
cause damages to the ground sockets.
d) After hardening of the concrete, the goal can be inserted into the sockets.
5. Maintenance, safety and storage instructions
This goal is only constructed for Handball and not for other purposes. Check all screwed fas-
tenings before use and repeat it from time to time. It has to be protected against overturning at
any time.
Do not climb net or goal frame. It is not allowed to x additional parts or extensions at the goal
frame which may impair the safety of the goal (according to EN 749).
Check screwed fastenings regularly and change damaged and wearing parts if need be. The unit should be maintained once a
year by skilled personnel.
Notice: Due to our continuous quality check of products and equipment technical modications are possible.
To avoid damage and misuse goals have to be stored secured and in an upright position when not in use.
Only use water for cleaning the surfaces. Do not use alcohol or any aggressive chemicals!