Spotlight HAL LED 55 XL User manual

Manuale utente - User manual
HAL LED 55 XL
HAL LED 90 XL

HAL LED 55 XL - HAL LED 90 XL
2
SAFETY WARNING: Before using this product, read the present instructions carefully.
Spotlight srl will not be responsible for damage resulting from instructions not being followed.
HAL LED 55
DIMENSIONS (mm) AND WEIGHT (1,1 kg.)
ø203-210
ø120
187.5
ø250
ø160
ø250
189
ø203-210
min. 20 max 35
min. 20 max 35
HAL LED 90
DIMENSIONS (mm) AND WEIGHT (2,2 kg.)
116 218
59
PSU LED 90 - DIMENSIONS (mm) AND WEIGHT (1 Kg)

HAL LED 55 XL - HAL LED 90 XL
3
---
m 0,5 IP 20 tamax 35°C
Devices in Class III, with protection against electric shock based on supply at
extra-low safety voltage (SELV).
Do not stare at the operating light source.
Devices not suitable for being covered with heat-insulation material.
Risk Group: 1, in compliance with Standard EN 62471
50W@1,4A
90W@2,1A
+
-
RED
BLACK
LED DRIVER C.C.

HAL LED 55 XL - HAL LED 90 XL
RECYCLING
The product must be recycled or disposed of,
according to Directive 2002/96/CE.
4
INTRODUCTION
The luminaire you have bought complies to 2006/95/EC,
2004/108/EC and 2011/65/EU European Directives.
The label on the side of the luminaire lists the following
information:
• Model
• Mains supply voltage (V)
• Lamp wattage (W)
• Protection index (IP)
• maximum allowed ambient temperature in °C
• minimum flammable surface distance
INSTALLATION
• The luminaire has been designed for professional use
only
• Do not direct the light beam straight into somebody’s
eyes
• Remember to connect the safety cable, if required by
local health and safety regulations
ELECTRICAL CONNECTIONS
The luminaire has been designed to operate with a
100V to 240V supply, 50-60Hz.
Before and during the installation, make sure you
follow the guidelines below:
• Always check the earth continuity connection for the
line being used.
• Ensure the required voltage of the unit is the same as
the supplied one.
• The unit is designed for indoor use: if it is to be used
outdoor, ensure it is protected from dampness and
rain. (IP 20)
• This unit cannot be connected to a dimmer.
MAINTENANCE
Do not open the fixture. Maintenance should be
performed only by the manufacturer or by its service
agent.
The luminaire must be serviced at least once a year, to
check the integrity of its electrical and mechanical parts
and to keep software updated.

HAL LED 55 XL - HAL LED 90 XL
5
OPERATING MODE
The luminaire is designed to be used in different
operating modes:
• LOCAL POTENTIOMETER
• DMX
• RDM
DISPLAY INTERFACE
MENU
When switched on, the installed software version
is displayed, followed by the display of the default
settings, ie the currently set operating mode:
- Manual, for use with a potentiometer
- 1-3-channel mode, for DMX/RDM mode
followed by the DMX address assigned to the unit.
Pressing the ENTER key you access the settings and
browse through the submenus by pressing the NEXT
and PREV buttons, which in case of value type
entries will have the function of increasing
or decreasing the values; the changes can be
confirmed with the ENTER button or canceled with
the BACK button.
Struttura del menu - MENU GENERALE
Item Value Def Description
Dmx Settings Dmx settings submenu
Options Optional settings submenu
Info Information submenu
MENU DMX SETTING
Item Value Def Description
Dmx
Address 1..xxx 1 Dmx Address
Dmx
Personality
3 channels mode
2 channels mode
1 channels mode
1 channels mode Dmx Mode
MENU OPTIONS
Item Value Def Description
LED Delay OFF / 30, 60 ... 600 ms 120 ms Buffer time on LED
outputs
Dimming
Curve
LINEAR
QUADRATIC Quadratic Gamma Correction
Out
Frequency
500, 800,1000,1500...
10000,11000, 12000...
20000 Hz
1000 Hz PWM LED Frequency
Led Boost
(*)--- --- ---
Fan Mode
(*)--- --- ---
Display
Rotat.
STANDARD
ROTATED Standard
180 ° rotation of the
display. Standard =
keys to the right of
the display
Display
Standby
OFF
ON OFF
By selecting ON the
display turns off
automatically after 60
seconds of inactivity
Default
Set
It sets the default
for all the user
parameters
Factory
Setting For the Manufacturer only Factory default setting
(*) Not available with this fixture
PREV/- NEXT/+ BACKENTER
PREV/-
NEXT/+
BACK
ENTER
Manual
001
Manual
001

HAL LED 55 XL - HAL LED 90 XL
6
MENU INFO
Item Value Description
LED Temperat. XX°C LED temperature (*)
Board Temperat. XX°C Motherboard edges
temperature
Led Time 00 Hr – 00 min Output operation time
Unit Time 00 Hr – 00 min Unit operation time
Software
Version
V. ....
Release date
It displays the software
version
(*) Not available with this fixture
Mappa DMX
Mode Number of Channels
3 CH 3
2 CH 2
1 CH 1
DMX Personality 3: 3 channels mode
#Nome Descrizione
1 DIMMER 0..255
Dimmer
from OFF (level 0)
to ON (level 255)
2DIMMER
FINE 0..255
Dimmer fine
from OFF (level 0)
to ON (level 255)
3 STROBO
0 INACTIVE STROBO
1..255
Strobo
from slow (3,86 s)
to fast (30 ms)
DMX Personality 2: 2 channels mode
#Nome Descrizione
1 DIMMER 0..255
Dimmer
from OFF (level 0)
to ON (level 255)
2 STROBO
0 INACTIVE STROBO
1..255
Strobo
from slow (3,86 s)
to fast (30 ms)
DMX Personality 1: 1 channels mode
#Nome Descrizione
1 DIMMER 0..255
Dimmer
from OFF (level 0)
to ON (level 255)

HAL LED 55 XL - HAL LED 90 XL
7
INPUTS PRIORITIES: LTP
The last input (DMX or Potentiometer) that is modified
has priority over the others.
On the display, in the main screen, if the last received
signal comes from the potentiometer, MANUAL is
indicated, while if the last received signal is DMX
the current DMX mode is indicated.
Absence of DMX signal
In the absence of a DMX signal, the last value received is
retained during normal operation.
In the absence of DMX signal at startup, instead, the
value set by the potentiometer has priority.
RDM
This fixture supports the RDM protocol, latest version
(ANSI E1.20 - 2010). The following parameters are
supported:
Plasa/ESTA Denomination Number of Channels
DEVICE_INFO Reading of the following parameters:
- RDM protocol version
- Device Model ID
- Product category
- ID version sw
- Number of DMX channels
- DMX mode index
- DMX address
- Number of sub-devices
- Number of sensors
IDENTIFY_DEVICE LEDs power on to allow to visually
identify the fixture
DMX_START_ADDRESS DMX address setting/reading
SOFTWARE_VERSION_LABEL Text description version sw
SUPPORTED_PARAMETERS List of supported parameters
DMX_PERSONALITY DMX mode setting
DMX_PERSONALITY_
DESCRIPTION
Obtaining textual description of
DMX mode
DEVICE_MODEL_DESCRIPTION Text description of the device model
MANUFACTURER_LABEL Text description manufacturer
SENSOR_DEFINITION,
SENSOR_VALUE
Display of the values read by the
temperature sensor, expressed in
tenths of Celsius degree

Spotlight s.r.l.
Via Sardegna 3
20098 S. Giuliano Milanese
Milano - Italy
Tel. [phone]
Fax [phone]
E-mail: [email protected]
www.spotlight.it
HAL LED 55 XL - HAL LED 90 XL