SPX S2045 User manual

S200 Series
CENTRIFUGAL PUMP
FORM NO.: 95-03080 REVISION: 12/2010 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT.
INSTRUCTION MANUAL

Information contained in this manual is subject to change
without notice and does not represent a commitment on the
part of SPX Corporation. No part of this manual may be
reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and
recording, for any purpose, without the express written per-
mission of SPX Corporation.
Copyright © 2005, 2010 SPX Corporation.
All Rights Reserved.
Revision Date: 12/2010
Publication: 95-03080
SPX Flow Technology
611 Sugar Creek Road
Delavan, WI 53115 USA
Tel: [phone] or [phone]
Fax: [phone] or [phone]
E-mail: [email protected]
Web site: www.spx.com

Table of Contents Waukesha Cherry-Burrell
Page 4 95-03080 12/2010
Warranty ..................................................................................................... 6
Shipping Damage or Loss ...........................................................................6
Warranty Claim ...........................................................................................6
Safety .......................................................................................................... 7
Care of Stainless Steel .............................................................................. 8
Stainless Steel Corrosion ............................................................................8
Elastomer Seal Replacement Following Passivation ..................................8
Introduction ................................................................................................ 9
Factory Inspection .......................................................................................9
Receiving Your Pump .................................................................................9
Receiving and Inspection ................................................................9
Pump Characteristics ..................................................................................10
S200 Series Base Mount Description .........................................................10
Base Mount Components ................................................................10
Motor Adapter ..................................................................................11
Stand ...............................................................................................11
Base (Optional) ...............................................................................11
Performance Characteristics .......................................................................13
Authorization ...................................................................................13
Standard Construction .....................................................................13
Construction Options .......................................................................13
Operating Parameters .................................................................................14
Installation .................................................................................................. 23
Pump Location ............................................................................................23
Pump Leveling ............................................................................................23
Supply and Discharge Piping/Valves ..........................................................23
Installations That May Cause Operation Problems .....................................25
Electrical Connections .................................................................................25
Flush Seal Option ........................................................................................26
Type 4 Seal (Double mechanical with flush) ...................................26
Before First Startup .....................................................................................26
Clean Pump and Piping ...................................................................26
Cleaning Safety Procedures .......................................................................27
Manual Cleaning .............................................................................27
Cleaning-In-Place (CIP) ..................................................................27
Preliminary Test Run ...................................................................................27
Ammeter Test ..............................................................................................27
Operation .................................................................................................... 28
Starting the Pump .......................................................................................28
Priming the Pump ........................................................................................28
Priming the Pump With the Feed Source Above Pump Level .........28
Priming the Pump With the Feed Source Below Pump Level .........29
Stopping the Pump ......................................................................................29
Maintenance ............................................................................................... 30
Scheduled Maintenance ..............................................................................30
Routine Maintenance ......................................................................30
Pump Disassembly with Type 1 Seal ..........................................................30
Removal of the Water Cascade ......................................................30

Waukesha Cherry-Burrell Table of Contents
12/2010 95-03080 Page 5
Inspect Parts ....................................................................................32
Pump Assembly with Type 1 Seal ..............................................................33
Backplate Assembly ........................................................................33
Backplate/Impeller Assembly ..........................................................33
Pump Disassembly with Type 4 Double Seal ..............................................35
Removal of the Water Cascade .......................................................36
Pump Assembly with Type 4 Double Seal ..................................................38
Disassembly of Modular Base Mounted Pumps ..........................................40
Disassembling The Outer Seal Assemblies ....................................42
Assembling the Outer Seal Assemblies ..........................................42
Pre-assembled (Cartridge) Seals . .............................................................43
Disassembly of Pre-assembled (Cartridge) Seals ...........................43
Assembly of a Pump With Pre-assembled (Cartridge) Seals ..........44
Pedestal Base Mounted Pump Housing Lubrication ...................................46
Lubrication Schedule .......................................................................46
Servicing the Electric Motor .........................................................................46
General Service Information ............................................................46
Motor Lubrication Instructions .........................................................46
Standard Seal Dimensions ..........................................................................47
Cartridge Seal Dimensions ..........................................................................48
Parts Lists ...................................................................................................49
Seal Kits ......................................................................................................49
Basic Seal Kit - Type 1 Seal - Sanitary Pump Model ......................49
Complete Seal Kit - Type 1 Seal - Sanitary Pump Model ................49
Basic Seal Kit - Type 4 Seal - Sanitary Pump Model ......................50
Complete Seal Kit - Type 4 Seal - Sanitary Pump Model ................50
Class VI Elastomer Kits ...................................................................51
Motor Shaft Shims .......................................................................................51
Seal Components All Pumps .......................................................................52
S2045 Components (Close Coupled) ..........................................................54
S2065/S2065LV/S2065HV Components (Close Coupled) .........................56
S2075 Components (Close Coupled) ..........................................................58
S2085/2085LV Components (Close Coupled) ............................................60
S2092 Components (Close Coupled) ..........................................................62
Pedestal Mounted Pumps - Small Bore ......................................................64
Pedestal Mounted Pumps - Large Bore ......................................................68
Motor Mounts .............................................................................................72
Troubleshooting .........................................................................................73

Warranty Waukesha Cherry-Burrell
Page 6 95-03080 12/2010
Warranty
Seller warrants its products to be free from defect in materials and workmanship
for a period of one (1) year from the date of shipment. This warranty shall not
apply to products which require repair or replacement due to normal wear and
tear or to products which are subjected to accident, misuse or improper mainte-
nance. This warranty extends only to the original Buyer. Products manufactured
by others but furnished by Seller are exempted from this warranty and are limited
to the original manufacturer’s warranty.
Seller’s sole obligation under this warranty shall be to repair or replace any prod-
ucts that Seller determines, in its discretion, to be defective. Seller reserves the
right either to inspect the products in the field or to request their prepaid return to
Seller. Seller shall not be responsible for any transportation charges, duty, taxes,
freight, labor or other costs. The cost of removing and/or installing products which
have been repaired or replaced shall be at Buyer’s expense.
Seller expressly disclaims all other warranties, express or implied, including with-
out limitation any warranty of merchantability of fitness for a particular purpose.
The foregoing sets forth Seller’s entire and exclusive liability, and Buyer’s exclu-
sive and sole remedy, for any claim of damages in connection with the sale of
products. In no event shall Seller be liable for any special consequential incidental
or indirect damages (including without limitation attorney’s fees and expenses),
nor shall Seller be liable for any loss of profit or material arising out of or relating to
the sale or operation of the products based on contract, tort (including negli-
gence), strict liability or otherwise.
Shipping
Damage or
Loss
If equipment is damaged or lost in transit, file a claim at once with the delivering
carrier. The carrier has signed the Bill of Lading acknowledging that the shipment
has been received from the seller in good condition. Seller is not responsible for
the collection of claims or replacement of materials due to transit shortages or
damages.
Warranty Claim Warranty claims must have a Returned Goods Authorization (RGA) from the
Seller before returns will be accepted.
Claims for shortages or other errors, exclusive of transit shortages or damages,
must be made in writing to Seller within ten (10) days after delivery. Failure to give
such notice shall constitute acceptance and waiver of all such claims by Buyer.

Waukesha Cherry-Burrell Safety
12/2010 95-03080 Page 7
Safety
READ AND UNDERSTAND THIS MANUAL
PRIOR TO INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT
We recommend users of our equipment and designs follow the latest Industrial Safety Standards. At a mini-
mum, these should include the industrial safety requirements established by:
1. Occupational Safety and Health Administration (OSHA), Title 29 of the CFR
Section 1910.212- General Requirements for all Machines
2. National Fire Protection Association, ANSI/NFPA 79
ANSI/NFPA 79- Electrical Standards for Industrial Machinery
3. National Electrical Code, ANSI/NFPA 70
ANSI/NFPA 70- National Electrical Code
ANSI/NFPA 70E- Electrical Safety Requirement for Employee Workplaces
4. American National Standards Institute, Section B11
Attention: Servicing energized industrial equipment can be hazardous. Severe injury or death can result from
electrical shock, burn, or unintended actuation of controlled equipment. Recommended practice is to discon-
nect and lockout industrial equipment from power sources, and release stored energy, if present. Refer to the
National Fire Protection Association Standard No. NFPA70E, Part II and (as applicable) OSHA rules for Con-
trol of Hazardous Energy Sources (Lockout-Tagout) and OSHA Electrical Safety Related Work Practices,
including procedural requirements for:
• Lockout-tagout
• Personnel qualifications and training requirements
• When it is not feasible to de-energize and lockout-tagout electrical circuits and equipment before working
on or near exposed circuit parts
Locking and Interlocking Devices: These devices should be checked for proper working condition and capa-
bility of performing their intended functions. Make replacements only with the original manufacturer’s renewal
parts or kits. Adjust or repair in accordance with the manufacturer’s instructions.
Periodic Inspection: Industrial equipment should be inspected periodically. Inspection intervals should be
based on environmental and operating conditions and adjusted as indicated by experience. At a minimum, an
initial inspection within 3 to 4 months after installation is recommended. Inspection of the electrical control sys-
tems should meet the recommendations as specified in the National Electrical Manufacturers Association
(NEMA) Standard No. ICS 1.3, Preventative Maintenance of Industrial Control and Systems Equipment, for the
general guidelines for setting-up a periodic maintenance program.
Replacement Equipment: Use only replacement parts and devices recommended by the manufacturer to
maintain the integrity of the equipment. Make sure the parts are properly matched to the equipment series,
model, serial number, and revision level of the equipment.
Warnings and cautions are provided in this manual to help avoid serious injury and/or possible damage to
equipment:
DANGER: marked with a stop sign.

Immediate hazards which WILL result in severe personal injury or death.
WARNING: marked with a warning triangle.

Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION: marked with a warning triangle.

Hazards or unsafe practices which COULD result in minor personal injury or product or property
damage.

Care of Stainless Steel Waukesha Cherry-Burrell
Page 8 95-03080 12/2010
Care of Stainless Steel
Stainless Steel Corrosion Corrosion resistance is greatest when a layer of oxide film is
formed on the surface of stainless steel. If film is disturbed or
destroyed, stainless steel becomes much less resistant to corro-
sion and may rust, pit or crack.
Corrosion pitting, rusting and stress cracks may occur due to
chemical attack. Use only cleaning chemicals specified by a repu-
table chemical manufacturer for use with 300 series stainless
steel. Do not use excessive concentrations, temperatures or
exposure times. Avoid contact with highly corrosive acids such as
hydrofluoric, hydrochloric or sulfuric. Also avoid prolonged con-
tact with chloride-containing chemicals, especially in presence of
acid. If chlorine-based sanitizers are used, such as sodium
hypochlorite (bleach), do not exceed concentrations of 150 ppm
available chlorine, do not exceed contact time of 20 minutes, and
do not exceed temperatures of 104°F (40°C). Corrosion discolor-
ation, deposits or pitting may occur under product deposits or
under gaskets. Keep surfaces clean, including those under gas-
kets or in grooves or tight corners. Clean immediately after use.
Do not allow equipment to set idle, exposed to air with accumu-
lated foreign material on the surface. Corrosion pitting may occur
when stray electrical currents come in contact with moist stain-
less steel. Ensure all electrical devices connected to the equip-
ment are correctly grounded.
Elastomer Seal
Replacement Following
Passivation
Passivation chemicals can damage product contact areas of
equipment. Elastomers (rubber components) are most likely to be
affected. Always inspect all elastomer seals after passivation is
completed. Replace any seals showing signs of chemical attack.
Indications may include swelling, cracks, loss of elasticity or any
other noticeable changes when compared with new components.

Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 9
Introduction
Factory Inspection Each Waukesha pump is shipped completely assembled, lubri-
cated and ready for use. (Make sure you review “Operation” on
page 27 before operating your pump).
Receiving Your Pump All ports are covered at the factory to keep out foreign objects
during transit. If the covers are missing or damaged, remove the
pump cover and thouroughly inspect the fluid head. Be sure the
pumping head is clean and free of foreign material before rotating
the shaft.
Receiving and Inspection
1. WCB equipment is inspected prior to shipment. When leaving
the factory, it is well-crated for normal transportation proce-
dures. WCB cannot, however, guarantee safe arrival. There-
fore, upon receipt of this equipment, check the received items
against the packing list for damaged or missing parts. Check
the packing material thoroughly for small parts.
2. Visually inspect for damage or loss. Immediately report any
damage or loss to the delivery carrier while present. Follow-
ing the immediate notification of the lost or damaged parts,
make a claim against the carrier including a detailed descrip-
tion of the loss or damage, and a cash value. WCB's respon-
sibility terminates F.O.B. point of manufacture unless
otherwise specified per the General Terms and Conditions of
Sale as published by WCB and amended from time to time.
Contact WCB Order Services if shipping information is
required for handling claims.
See also “Shipping Damage or Loss” on page 6.

Introduction Waukesha Cherry-Burrell
Page 10 95-03080 12/2010
Pump Characteristics The Waukesha S200 Series Pump is built for extremely durable
service. The casing, backplate, and impeller/stub shaft are
machined from 316L stainless steel for extra strength and resis-
tance to line shock and corrosion. Large bearings and shaft pro-
vide positive alignment and minimize vibration.
The casing is clamped to the motor adapter bracket (close cou-
pled) or bearing housing (base mount) for easy disassembly
while permitting 360 degree rotation of the discharge port.
S200 Series pumps are available with three standard seal types:
• Type 1 - Single mechanical seal, externally-mounted and
balanced
• Type 1C - Single mechanical seal with water cascade flush
• Type 4 - Double mechanical seal with flush housing
All seal components are interchangeable between models. All
seal assemblies use an externally-mounted, balanced rotary seal
for longer seal life and better sealing capability. The stationary
seal face is reversible and replaceable.
S200 Series pumps are designed for a broad range of sanitary
and industrial applications. Sanitary models are designed for
clean-in-place and meet U.S.D.A. and 3A Standards.
S200 Series Base Mount
Description The Waukesha S200 Series Modular Base Mounted Centrifugal
Pump design consists of four components (in addition to the
pump and motor). These components are used in various combi-
nations and arrangements to provide flexibility to meet various
needs.
Base Mount Components
Bearing Housing (Pump Adapter)
• Bearing housing is made of epoxy-coated cast iron w/316 SS
shaft, ball bearings.
• The adapter mounts to the pump components (same
components used for close coupled pumps).
• Bearing housing also includes coupling for motor shaft plus
guards used in style "B" & "C" arrangements.
Style "B" Arrangement
The style "B" arrangement is composed of the bearing housing,
motor adapter and pedestal stand attached to the bearing
housing; for use with NEMA C-face motors. All motors must have
feet for attachment of supports. See Figure 1.
Style "C" Arrangement
The style "C" arrangement is composed of the bearing housing ,
guard and pedestal stand attached to the bearing housing; for
use with foot mounted T-frame motors. The pump and motor are
mounted and supported independently. See Figure 2.
Figure 1 - Style B
Figure 2 - Style C

Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 11
Motor Adapter
• Made of epoxy-coated cast iron
• Used to mount a standard NEMA C-face motor onto bearing
housing
• Used to provide an accurate, rigid shaft alignment
• Used in style "B" arrangements
Stand
• The stand (pedestal) is made of epoxy-coated cast iron.
• The stand attaches under the motor adapter or bearing
housing.
Base (Optional)
• The epoxy-coated channel base is used in style "B" & "C"
arrangements. See “Table of Base Size Used on Pedestal-
Mounted Centrifugal Pumps” on page 19.
Figure 3 - Common Part Identification
Figure 4 - Common Part Identification
Table 1: Callout Table for Figure 3
A. Motor Shims H. O-ring
B. Motor Adapter J. Impeller
C. Lock Washer K. O-ring
D. Cap Screws L. Impeller
Retainer
E. Seal Guard
F. Seals (detail
not shown) M. Clamp
N. Casing
G. Backplate
Table 2: Callout Table for Figure 4
A. Motor Shims
B. Deflector
C. Spring Retainer
D. Springs
E. Tabbed Washer
F. O-ring
G. Rotary Seal
H. Cap Screws
J. Seat Retainer
K. Stationary Seal
L. L-gasket
M. Water Cascade Block

Figure 5 - Common Part Identification
Introduction Waukesha Cherry-Burrell
Page 12 95-03080 12/2010
Table 3: Callout Table for Figure 5
A. Motor Shims L. Tabbed Washer
B. Slinger M. O-ring
C. L-gasket N. Rotary Seal
D. Stationary Seal P. Stationary Seal
E. Rotary Seal R. L-gasket
F. O-ring S. O-ring
G. Tabbed Washer T. Housing
H. Springs U. O-ring
J. Spring Retainer V. Seat Retainer
K. Springs W. Cap Screws

Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 13
Performance
Characteristics Authorization
3A/USDA (Sanitary Models)
Standard Construction
• Casing: 316L Stainless Steel
• Port Connections: S-Line
• Backplate: 316L Stainless Steel
• Impeller W/Integral Shaft: 316L Stainless Steel
• Impeller Retainer: 316L Stainless Steel
• Shaft Seal: Single Mechanical, externally-balanced (Type 1)
• Rotary Seal Material: Carbon
• Stationary Seal: Purebide
• Elastomers: FDA approved FKM
• Finish: All product contact surfaces provided with a sanitary
polish (20Ra mechanical). The motor adapter bracket is
Nedox coated cast iron.
• Mounting: Close coupled for JM shafted motors
Construction Options
Ports
Buttweld
Flange 150# MSS
Flange 150# ASA
DIN
DIN Form A
SMS
Seal Type
• Water Cascade (Type 1C)
• Double Mechanical with flush (Type 4 Shaft Seal)
• WFI - Special Type 4 shaft seal for water for injection
applications
• Commercially available seals (Contact your WCB
representative for details)
Rotary Seal Material
Purebide
Silicone Carbide
Tungsten Carbide
Stationary Seal
Silicone Carbide
Tungsten Carbide

Introduction Waukesha Cherry-Burrell
Page 14 95-03080 12/2010
Elastomers
EPDM (FDA approved)
Silicone (FDA approved)
Teflon Encapsulated (FDA approved)
FKM
FFKM
Finishes/Product Contact Surfaces
15RA
20RA
Electropolish
Leg Kit
See “Motor Mounts” on page 72.
Base Mounting
Footed C-face motors
T-Frame motors. Note: T-Frame motors can be configured
with or without bases, couplings or coupling covers.
Pedestal Mounted
Two types of stands; see “Base Mount Components” on page 10.
Motors
NEMA JM (standard) totally enclosed fan cooled (TEFC) for
close-coupled pumps
1750 or 3500 RPM single phase 115/230 volt and 3 phase
230/460 volt
Optional Enclosures
Washdown
Explosion proof
Severe Duty/Chemical Duty
Operating Parameters Nominal Capacity
Up to 900 U.S. GPM (204 Cubic meters/hour)
Viscosity
Up to 1500 CPS
Differential Pressure
UP to 340 Feet (100 meters)
Temperature
Up to 450°F (230°C)
Nominal Speeds
1450 or 2900 RPM - 50HZ
1750 or 3500 RPM - 60HZ

Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 15
S200 Series Capacities
Dimensions
Sanitary
Model Inlet Size inch (mm) Outlet Size inch (mm) Maximum Capacity GPM (M3/HR)
S2045 1.5 (40) 1.5 (40) 190 GPM (43)
2.0 (50) 1.5 (40) 190 GPM (43)
S2065LV
1.5 (40) 1.5 (40) 195 GPM (44)
2.0 (50) 1.5 (40) 195 GPM (44)
2.5 (65) 1.5 (40) 194 GPM (44)
S2065 2.5 (65) 2.0 (50) 400 GPM (91)
S2065HV 3.0 (75) 2.0 (50) 500 GPM (114)
S2075 3.0 (75) 1.5 (40) 300 GPM (68)
S2085LV 2.0 (50) 1.5 (40) 140 GPM (32)
S2085 3.0 (75) 2.5 (65) 900 GPM (204)
4.0 (100) 2.5 (65) 900 GPM (204)
S2092 3.0 (75) 2.0 (50) 700 GPM (159)
Figure 6 - Foot Print Dimensions

Table 4: Table of Dimensions for Figure 6, page 15
Frame A inch
(mm)
O
inch
(mm)
D
inch
(mm)
F
inch
(mm)
AB
inch
(mm)
145JM 9.32 (237) 7.1 (180) 3.5 (89) 0.88 (22) 5.73 (145)
182JM 9.32 (237) 8.1 (206) 4.5 (114) 0.88 (22) 5.73 (145)
184JM 11.11 (282) 8.49 (216) 4.5 (114) 1.09 (28) 6.87 (174)
213JM 13.18 (335) 10.39 (264) 5.25 (133) 1.38 (35) 8.04 (204)
215JM 13.18 (335) 10.39 (264) 5.25 (133) 1.38 (35) 8.04 (204)
254JM 15.34 (390) 11.39 (289) 6.25 (159) 1.38 (35) 9.40 (239)
256JM 15.34 (390) 11.39 (289) 6.25 (159) 1.38 (35) 9.40 (239)
284JM 20.78 (528) 14.44 (367) 7.0 (178) 2.0 (51) 13.12 (333)
286JM 20.49 (520) 14.44 (367) 7.0 (178) 2.0 (51) 13.12 (333)
324JM 23.05 (585) 16.25 (413) 8.0 (203) 2.5 (63) 14.61 (371)
326JM 23.05 (585) 16.25 (413) 8.0 (203) 2.5 (63) 14.61 (371)
Introduction Waukesha Cherry-Burrell
Page 16 95-03080 12/2010
NOTE: Figure 6 dimensions for the Inlet, Outlet, items X,Y, and Z are listed in Table 7 on page 17.
Table 5: Table of Dimensions for Figure 6, page 15
FRAME
PUMP SIZE
S2045 S2065 S2065LV S2065HV
LP CP LP CP LP CP LP CP
Inches
(mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm)
145JM 2.92 (74) 18.18 (461) 2.71 (69) 18.43 (468) 2.71 (69) 17.93 (455) 2.71 (69) 18.85 (479)
182JM 2.92 (74) 19.56 (497) 2.71 (69) 19.81 (503) 2.71 (69) 19.31 (490) 2.71 (69) 20.23 (514)
184JM 2.92 (74) 20.81 (529) 2.71 (69) 21.01 (534) 2.71 (69) 20.56 (522) 2.71 (69) 21.43 (544)
213JM -- -- 2.97 (75) 22.81 (579) 2.97 (75) 22.31 (567) 2.97 (75) 23.23 (590)
215JM -- -- 2.97 (75) 23.94 (608) 2.97 (75) 23.44 (595) 2.97 (75) 24.36 (618)
254JM -- -- 3.97 (101) 26.07 (662) 3.97 (101) 25.57 (649) 3.97 (101) 26.49 (673)
256JM -- -- 3.97 (101) 27.83 (707) 3.97 (101) 27.33 (694) 3.97 (101) 28.25 (718)
284JM -- -- 3.97 (101) 31.43 (798) 3.97 (101) 30.93 (786) 3.97 (101) 31.85 (809)
286JM -- -- 3.97 (101) 31.64 (804) 3.97 (101) 31.14 (791) 3.97 (101) 32.06 (814)
324JM -- -- -- -- -- -- -- --
326JM -- -- -- -- -- -- -- --

Table 6: Table of Dimensions for Figure 6, page 15
Frame
Pump Size
S2075 S2085 S2085LV S2092
LP CP LP CP LP CP LP CP
Inches
(mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm) Inches (mm)
145JM 2.75 (70) 18.17 (461) 2.75 (70) 18.84 (478) 2.75 (70) 18.17 (461) 2.75 (70) 18.78 (477)
182JM 2.75 (70) 19.55 (497) 2.75 (70) 21.21 (513) 2.75 (70) 19.55 (497) 2.75 (70) 20.16 (512)
184JM 2.75 (70) 20.80 (528) 2.75 (70) 21.46 (545) 2.75 (70) 20.80 (528) 2.75 (70) 21.41 (544)
213JM 2.84 (72) 22.39 (569) 2.84 (72) 23.06 (586) 2.84 (72) 22.39 (569) 2.84 (72) 23.00 (584)
215JM 2.84 (72) 23.52 (597) 2.84 (72) 24.19 (614) 2.84 (72) 23.52 (597) 2.84 (72) 24.13 (613)
254JM 3.84 (98) 25.65 (651) 3.84 (98) 26.32 (668) 3.84 (98) 25.65 (651) 3.84 (98) 26.26 (667)
256JM 3.84 (98) 27.41 (696) 3.84 (98) 28.08 (713) 3.84 (98) 27.41 (696) 3.84 (98) 28.02 (712)
284JM 3.84 (98) 31.01 (788) 3.84 (98) 31.68 (805) 3.84 (98) 31.01 (788) 3.84 (98) 31.62 (803)
286JM 3.84 (98) 31.22 (793) 3.84 (98) 31.89 (810) 3.84 (98) 31.22 (793) 3.84 (98) 31.83 (808)
324JM 3.84 (98) 33.11 (841) 3.84 (98) 33.78 (858) 3.84 (98) 33.11 (841) -- --
326JM 3.84 (98) 33.11 (841) 3.84 (98) 33.78 (858) 3.84 (98) 33.11 (841) -- --
Table 7: Table of Dimensions for Figure 6, page 15
Model Inlet
inch (mm) Outlet inch (mm) X inch (mm) Y inch (mm) Z inch (mm) MP inch (mm)
S2045 1.5 (38) 1.5 (38) 3.88 (99) 2.56 (65) 1.99 (51) 4.08 (104)
2.0 (51) 1.5 (40) 3.88 (99) 2.56 (65) 1.99 (51) 4.08 (104)
S2065 2.5 (64) 2.0 (51) 4.94 (125) 2.68 (68) 2.88 (73) 4.53 (115)
S2065LV
1.5 (38) 1.5 (38) 4.94 (125) 2.43 (62) 3.13 (79) 4.03 (102)
2.0 (51) 1.5 (38) 4.94 (125) 2.43 (62) 3.13 (79) 4.03 (102)
2.5 (64) 1.5 (38) 4.94 (125) 2.43 (62) 3.13 (79) 4.03 (102)
S2065HV 3.0 (76) 2.0 (51) 4.94 (125) 3.04 (77) 2.88 (73) 4.96 (126)
S2075 3.0 (76) 1.5 (40) 6.69 (170) 2.70 (69) 4.32 (110) 4.24 (108)
S2085 3.0 (76) 2.5 (64) 5.75 (146) 2.93 (74) 3.82 (97) 4.91 (125)
4.0 (102) 2.5 (64) 5.75 (146) 2.93 (74) 3.82 (97) 4.91 (125)
S2085LV 2.0 (51) 1.5 (40) 6.69 (170) 2.70 (69) 4.32 (110) 4.24 (108)
S2092 3.0 (76) 2.0 (51) 6.64 (169) 3.09 (78) 4.62 (117) 4.85 (123)
Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 17

Figure 7 - Style "B" and "C" Less Base Plate
Table 8: Table of Dimensions for Figure 7
Model Inlet
inch (mm) Outlet inch (mm)
BD
Sm Bore
inch (mm) Lg Bore inch (mm) Sm Bore inch(mm) Lg Bore inch (mm)
PS2045 1.5 (40) 1.5 (40) 15.0 (381) -- 2.7 (69) --
2.0 (50) 1.5 (40) 15.0 (381) -- 2.7 (69) --
PS2065LV
1.5 (40) 1.5 (40) 14.9 (378) 18.6 (472) 1.7 (43) 4.9 (124)
2.0 (50) 1.5 (40) 14.9 (378) 18.6 (472) 1.7 (43) 4.9 (124)
2.5 (65) 1.5 (40) 14.9 (378) 18.6 (472) 1.7 (43) 4.9 (124)
PS2065 2.5 (65) 2.0 (50) 15.1 (384) 18.9 (480) 1.7 (43) 4.9 (124)
PS2065HV 3.0 (75) 2.0 (50) 15.2 (386) 18.9 (480) 1.7 (43) 4.9 (124)
PS2075 3.0 (75) 1.5 (40) 14.7 (373) 18.4 (472) .6 (15) 3.9 (99)
PS2085LV 2.0 (50) 1.5 (40) 14.7 (373) 18.4 (472) .6 (15) 3.9 (99)
PS2085 3.0 (75) 2.5 (65) 15.1 (384) 18.9 (480) .6 (15) 3.9 (99)
4.0 (100) 2.5 (65) 15.1 (384) 18.9 (480) .6 (15) 3.9 (99)
PS2092 3.0 (75) 2.0 (50) 14.9 (378) 18.6 (472) .6 (15) 3.9 (99)
Introduction Waukesha Cherry-Burrell
Page 18 95-03080 12/2010
NOTE: Dimensions X,Y, and B apply to pumps with clamp connections.

Table 9: Table of Base Size Used on Pedestal-Mounted Centrifugal Pumps
Motor HP & RPM
Sanitary and Industrial Models
PS2045 PS2065LV PS2065/
PS2065HV PS2075 PS2085LV PS2085 PS2092
Up to 5 HP 1750 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
Up to 5 HP 3500 RPM SM.B. SM.B. SM.B.
7.5 HP 1750 RPM SM.B. SM.B.
7.5 HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
10 HP 1750 RPM SM.B. SM.B.
10 HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B. SM.B.
15 HP 1750 RPM
15 HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B.
20 HP 1750 RPM
20 HP 3500 RPM SM.B. SM.B. SM.B. SM.B. SM.B.
25 HP 1750 RPM
25 HP 3500 RPM
30 HP 1750 RPM
30 HP 3500 RPM LG.B. LG.B.
40 HP 1750 RPM
40 HP 3500 RPM LG.B. LG.B.
50 HP 1750 RPM
50 HP 3500 RPM LG.B. LG.B.
60 HP 3500 RPM LG.B. LG.B.
75 HP 3500 RPM LG.B. LG.B.
Waukesha Cherry-Burrell Introduction
12/2010 95-03080 Page 19
SM.B. = Small Base
LG.B. = Large Base

Introduction Waukesha Cherry-Burrell
Page 20 95-03080 12/2010
Baseplates are available in carbon steel channel base, carbon steel baseplate with feet or stainless steel base-
plate with feet.
Table 10: Base Channel Dimensions for Figure 8
Carbon Steel
Channel Base Carbon Steel Baseplate Stainless Steel Baseplate
10 x 26
12 x 32
15 x 32
15 x 40
16 x 41
18 x 40
18 x 50
12 x 26
14.6 x 32
17 x 41
17 x 50
12 x 32
17 x 41
17 x 50
Centrifugal S200 Series Pump and Pedestal Weights
Figure 8 - Base Channel Dimensions for Pedestal Mounted Centrifugal Pumps