Spypoint LINK-MICRO-S-LTE User manual

v.1.0
LINK-MICRO-S-LTE
QUICK START GUIDE

ENGLISH
2
In the box
NOTE: MicroSD memory card is sold separately.
1x LINK-MICRO-LTE camera
1x Antenna holder
1x Installation strap
1x Quickstart guide
1x SIM card that is preactivated and inserted in the camera
1x USB Micro USB cable
1x LIT-10 lithium battery pack
User manual, latest rmware, and FAQ available at:
support.spypoint.com
Components
SIM card slot
Slot for installation strap
Locking latch
Cable lock hole
12V jack
Standard ¼’’20 tripod mount
Solar panel
Antenna
Detection lens
MicroSD card slot
Light sensor
Delay light
Photo lens
LED
ON/OFF switch
"STATUS" light
Lithium battery outlet
1
2
3
4
5
6
7
8
9
10
12
13
15
16
11
17
14

ENGLISH
3
13
14
15
16
17
3
4
6
7
1
2
5
8
9
10
11
12

ENGLISH
4
CHARGING THE LITHIUM BATTERY
•Remove the lithium battery pack from the camera.
•Using the Micro USB cable, recharge the battery pack for about 12 hours.
•Once the lithium pack is fully charged, the red light will turn green.
HOW YOUR CAMERA USES SEVERAL POWER SOURCES
1. Your camera’s main source of power is the lithium battery pack (#LIT-10, included)
and oers longer battery life, roughly doubling that of standard AA batteries.
•The solar panel’s sole function is to recharge the lithium battery and will
operate when solar energy is detected.
•When the lithium battery pack power level becomes insucient, the
camera shuts down.
•The solar panel will continue recharging the lithium battery pack until the
power level is sucient. At this point, your camera will automatically turn
on and resume with your congured settings.
2. Moreover, the camera was designed to recognize and use a primary power
source other than the lithium battery pack:
•As soon as you plug an external 12V battery (#BATT-12V, sold separately)
into your camera, it becomes your camera’s new primary power source.
The lithium battery pack will only be used once the 12V battery is depleted.
•Simply plug the 12V cable into the 12V jack of the camera and connect the
other end to the 12V battery.
USING AN EXTERNAL 12V BATTERY
• Using an external 12V battery source does not recharge the lithium battery pack.
•The solar panel will not recharge an external 12V battery.
Getting started
Do not insert AA batteries into the lithium battery
compartment, as this could damage the camera.

ENGLISH
5
FORMATTING YOUR M
icro
SD CARD
Before inserting the MicroSD card into your camera, it must be reformatted via a
computer to ensure proper functionality.
Memory card is sold separately. Whether you choose to use a MicroSD card you
previously used in another device or a brand new one you've just bought, its
capacity must not exceed 32 GB and it must be reformatted. Do no use the‘’Quick
format’’option.
INSERTING A M
icro
SD CARD
•Ensure the camera is turned o.
•Insert a MicroSD memory card (up to 32 GB capacity) into the MicroSD card
slot with the label facing up.
•The card is inserted correctly when a click is heard.
This lithium battery is compatible with all SPYPOINT LINK-MICRO cameras and the CELL-LINK.
Getting started
LIT-10 BATTERY SPECIFICATIONS
Charging time ≈ 12 hours (with USB cable)
Operating temperature (-30 °C to+50 °C) (-22 °F to+122 °F)
Storage temperature (-40 °C to+60 °C) (-40 °F to+140 °F)
Voltage 3.7 Volts 10200mAh
Capacity 10200mAh
SPYPOINT hereby declares that this product is in compliance with the essential re-
quirements and other relevant provisions of Directive 2004/108/EC. The user can
obtain a copy of the Declaration of Conformity by e-mail at [email protected].
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
1. This device must not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.

ENGLISH
6
SPYPOINT APP
Follow these steps:
1. On Google Play
TM
or the App Store
TM
, search for "SPYPOINT app."
2. Download and install the app on your smartphone or tablet.
3. S tart the app. Select "ACTIVATE A DEVICE." In the list, select "LINK-MICRO-S-LTE"
then follow the steps.
4. When complete, a conrmation email will be sent to you with a generated password.
5. Log in to the SPYPOINT app using your email and password.
ACTIVATING YOUR CAMERA
You must activate your camera through the free SPYPOINT
app or the SPYPOINT.COM website.
FINDING THE ACTIVATION CODE
The activation code is located inside the camera case behind
the battery holder.You will need this unique code to activate
the LINK-MICRO-S-LTE.

ENGLISH
7
SPYPOINT.COM website
Follow these steps:
1. On the SPYPOINT.COM website, select "MY ACCOUNT" in the top navigation menu.
On the displayed page, select "Register," ll out the required elds, then log in.
2. Select the + sign on the far right of the page; in the list, select "LINK-MICRO-S-LTE"
then follow the steps.
3. When complete, a conrmation email will be sent to you with a generated password.
4. Log in to the MY ACCOUNT section of the SPYPOINT website using your
email and password.
ACTIVATING YOUR CAMERA
NOTE: You can activate additional cameras and switch
between them in the SPYPOINT app or website.
CHOOSING A PHOTO TRANSMISSION
PLAN FOR YOUR CAMERA
Select a photo transmission plan via the app or website.
1. Upon activating your camera, you will automatically benet from
our FREE monthly plan.
2. After your 30 days are up, you can select a new plan better suited
to your needs among the ones we oer or;
3. Keep your FREE monthly plan and continue receiving up to 100
photo transfers per month.

ENGLISH
8
Both the SPYPOINT app and website let you congure all the camera settings remotely.
They also provide basic information on your camera – such as: cellular signal
strength, battery level, and MicroSD card space used. This information is based
upon the latest connection with your camera.
New settings take eect every time the camera connects with app or website.
Below are the most basic settings you will congure.
BASIC PHOTO SETTINGS
Delay: Allows you to set the time interval between each detection before the
camera records the next photo or video.
Multishot: Allows you to set the number of photos per detection (up to 3) with a
5-second delay between each photo.
Sensitivity: Allows you to set the detection sensitivity of the camera.
Camera name: Allows you to name each owned camera with a 30-character limit.
CELLULAR SETUP
First transfer time: Allows you to choose the time when the camera makes its
rst transfer of the day.
Transfer frequency: Allows you to choose the number of daily transfers.
ADVANCED OPTIONS/CONFIGURATION
Schedule: Allows you to set the period of operation for each day of the week.
For a 24-hour operation mode, both the start and stop times must be 12 AM.
CONFIGURING YOUR CAMERA
NOTE:
Camera transfers are set by default to every 4 hours from midnight.
For a complete list of specifications, features,
and settings, visit our LINK-MICRO-S-LTE page at
www.spypoint.com.

ENGLISH
9
FIRST TIME SETUP
1. Turn on the camera.
2. The green "STATUS" light will ash while searching for a signal (can take a few minutes).
3. The "STATUS" light will light up in one of the following 3 colors:
-
Red: Insucient signal.
-
Orange: Acceptable signal.
-
Green: Optimal signal.
4. When the top right light ashes red, 30 seconds remain before the photo mode is
turned on. This allows you to leave the area without being photographed.
5. The camera is ready for use when all the lights turn o.
6. If the light is red during step 3, you should:
•Turn your camera o and then back on.
•Retry while pointing the antenna at dierent angles.
•Try moving it to a spot with better signal.
•Try our #CA-01 long-range cellular antenna (sold separately), which could help
improve signal strength.
STARTING YOUR CAMERA
1. Mount the camera using the installation strap.
2. The camera should be at the same height as the animal’s mid-body.
3. The targeted animal should be at 25 feet/7.5 meters away from the camera.
4. For brighter pictures at night, ensure you have elements in the background
to reect the IR ash.
INSTALLING YOUR CAMERA

ENGLISH
10
ONLY USE ORIGINAL SPARE PARTS AND ACCESSORIES.
If one day your camera has been used so intensively that it has to be replaced, or if
you no longer have any use for it, you are obliged to dispose of it at a recycling center.
Information on return points for your electrical appliance can be obtained from
your local waste disposal company or from your local administrative offices.
Electrical appliances not only contain valuable recyclable raw materials, but also
substances which, if disposed of improperly, can affect public health and the
environment. Help ensure that valuable raw materials are recycled when you return
your old appliance to a central collection point.
The WEEE (Waste Electrical and Electronic Equipment Directive ) symbol represents
the obligation that the labeled camera to be sent to a separate center for the proper
recycling of electrical and electronic equipment.
FREQUENCY RANGE:
800/ 850/ 900/ 1900/ 2100MHz
MAXIMUM TRANSMISSION POWER:
FREQUENCY
GSM850
EGSM900
DCS1800
PCS1900
GSM850 (8-PSK)
EGSM900 (8-PSK)
DCS1800 (8-PSK)
PCS1900 (8-PSK)
UMTS 2100
UMTS 1900
UMTS 900
UMTS 850
UMTS 800
DISPOSAL
FREQUENCY
MAX.
33DBM±2DB
33DBM±2DB
30DBM±2DB
30DBM±2DB
27DBM±3DB
27DBM±3DB
26DBM±3DB
26DBM±3DB
24DBM+1.7/3.7DB
24DBM+1.7/3.7DB
24DBM+1.7/3.7DB
24DBM+1.7/3.7DB
24DBM+1.7/3.7DB