Stagnoli HERMES User manual

Istruzioni Instructions Instructions
- 1 -
HERMES
I - Motoriduttore elettromeccanico per cancelli battenti con fermi e
senza fermi meccanici
GB - The electromechanical gear motor for swing gates with end
without mechanical stops
- Motoréducteur électromécanique pour portails à battants avec
ou sans butées mécaniques

Istruzioni Instructions Instructions
- 11 -
Attention!
•This manual is for qualified installers only and not for the end user. It is the installer’s job
to explain to the user how the automatism works, about possible hazards related to it
and the need for periodical maintenance.
•Installation must be carried out by qualified personnel only, observing current
standards concerning automatic closing systems. More specifically, installation
conformity calls for observance of directive 89/392 and standards EN 12453 and EN
12445.
•Make absolutely certain the power is disconnected before carrying out any work on
the device.
•The power lead must only be connected to supply lines fitted with adequate electrical
protection; a circuit breaker must also be installed to guarantee disconnection of all
the phases from the mains with a distance of at least 3.5 mm between the contacts.
•Be particularly careful when evaluating the safety devices to install and their location.
Always install an emergency stop device that will cut power off in the case of
necessity.
•Use original components only. Stagnoli is not liable for damages if any other
components are used.
•Do not work on the device if your hands or feet are damp or wet and do not leave it
outdoors exposed to the weather.
•This device must only be used for the purpose it has been expressly designed, any
other use is considered improper and therefore dangerous.
•Only qualified personnel must be allowed to service the unit, including changing the
courtesy light bulb whenever needed.
•Make sure that the gate structure is solid, well balanced and suitable to be motorised.
Also ensure there are no points of friction when the gate is moving.

Istruzioni Instructions Instructions
- 12 -
4x1RX
2x1
2x1TX
2x2.5+3x0.54x1RX
TRG58
2x1.5
2x1-TX
Control Panel
3x1.5
230V
HERMES
ZEUSTransmitter
POLIEMO post
mounted photocell
PEGASUSBlinker
ASMKeySelector
ARGO wall mounted
photocell
HERMES:generalapplication
2x2.5+3x0.5

Istruzioni Instructions Instructions
- 13 -
technical specifications
Limits of use
SHORT HERMES LONG HERMES
GATE 1 m 1,5 m 1,8 m 2 m 1 m 1,5 m
2 m 2,5 m
200 g   
150 g     
120 Kg   
100 g        
Technical data HERMES
Supply 230V~ 50Hz
Input current (A) 0,7
Motor supply 24V–––––
Motor power (W) 100
Manoeuvre time 90° (sec) 15-20
Thrust force (N) 1200
Wor ing temperature (°C) -20 ...+60
Duty cycle (%) 70
IP protection level 44
Weight (Kg) 3

Istruzioni Instructions Instructions
- 14 -
Preliminary checks and fixing the gear motor
•Chec that the gate structure is sufficiently sturdy and there are no points of friction.
•Ma e sure the gate hinges are wor ing properly and adequately lubricated.
•Chec there are mechanical stops in closing and opening.
•Prepare for fixing the gear motor to the gate as illustrated in figure.
Attention!
To ensure the smooth operation of the engine installation of units strictly observe the
following.
B \ A 80 100 120 140 160 180 200 220 240 260
100 90 100 110 115 120 105 100 95 90 90
120 90 100 110 110 110 100 95 90
140 100 105 105 100 95 90
160 95 100 100 90
180 95 95
200 95
B \ A 80 100 120 140 160 180 200 220 240 260
100 730 745 765 780 795 770 755 735 710 700
120 750 765 785 790 795 775 755 735
140 785 795 800 795 775 755
160 800 805 810 785
180 820 820
200 840
TABLE OF INSTALLATION QUOTE FOR HERMES WITHOUT MECHANICAL STOPS
OPENING ANGLE : C
POSITION FRONT BRACKET : D

Istruzioni Instructions Instructions
- 15 -
B \ A 80 100 120 140 160 180 200 220 240 260
100 810 846 885 920 956 951 956 956 951 961
120 832 867 907 932 957 957 957 957
140 888 918 943 958 958 958
160 905 930 955 950
180 927 947
200 950
TOTAL EXETENTION : E
Attention!
Before any power to the motor, including the planning stage, it is necessary to achieve
the right positioning and passage of the mechanical stops.
B \ A 80 100 120 140 160 180 200 220
100 105 110 115 110 100 95 90
120 100 110 110 100 95 90
140 90 100 105 105 95 90
160 90 95 100
180 95 95
200 90
B \ A 80 100 120 140 160 180 200 220
100 810 800 800 790 760 740 725
120 810 810 800 785 765 745
140 830 810 820 805 785 765
160 830 830 820
180 830 825
200 835
B \ A 80 100 120 140 160 180 200 220
100 911 921 941 951 941 941 946
120 912 932 942 947 947 947
140 913 913 943 948 948 948
160 915 935 945
180 937 952
200 945
TABLE OF INSTALLATION QUOTE FOR HERMES WITH MECHANICAL STOPS
ANGOLO DI APERTURA : C
POSITION FRONT BRACKET : D
TOTAL EXETENTION : E

Istruzioni Instructions Instructions
- 16 -
ixing the brackets to the post and gate
Once you have verified the optimum conditions for placing the plates and their alignment (fig. 2),
fix them definitively to the post and gate, either welding them or using expansion bolts (on
masonry posts).
figure 2
ixing the gear motor
Loc the gear motor at the bac with a hex head screw and relative nut and washer .
figure 3
Position the gear motor frontwards with the hex head screw and relative nut and washer.
figure 4

Istruzioni Instructions Instructions
- 17 -
ADJUSTING MECHANICAL STOPS
Attention!
Before any power to the motor, including the planning stage, it is necessary to achieve
the right positioning and passage of the mechanical stops.
1. OPENING ROAMING PROFILE
2. ADJUSTING MECHANICAL STOPS
-Once you have positioned the mechanical stops must be properly
locked, with a key of 17 will prevent the latch from moving when
tightening that runs with an Allen wrench 4.

Istruzioni Instructions Instructions
- 18 -
3. CLOSING ROAMING PROFILE
Manual release
1. Put the ey in with the point facing upwards and turn it counter cloc wise 90°.
2. Move the gate by hand

Istruzioni Instructions Instructions
- 19 -
Brown
Green
White
Enc +
Enc -
Enc
Blue Red
APM
CHM
M
Hermes electrical connections

Istruzioni Instructions Instructions
- 29 -

Istruzioni Instructions Instructions
- 30 -