Stahl Tranberg TEF 9964 User manual

R. Stahl Tranberg AS
E[email protected] | stahl-tranberg.com
Main office: Strandsvingen 6 | N-4032 Stavanger | Norway | T+47 51 57 89 00 | F+47 51 57 89 50
Office Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T+47 24 08 44 10
IMPORTANT
Read this instruction carefully before installing the
product
996A105480
LIGHTING
TEF 9964 XENON
HELIDECK FLOODLIGHT EEx de
ZONE 1, ZONE 2 & SAFE AREA
USER MANUAL
Subject to change without prior notice TUM1023 REV. D 14.07.2017

TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval,
may be a safety violation. The manufacturer will in no
circumstance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specific procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
• 17 mm wrench –for assembling the floodlight.
• 13 mm wrench –for adjusting the angle of the light.
• 8 mm flat screwdriver –for open/closing the cover of the
junction box.
• 3 mm flat screwdriver –for installing the cable in the
terminal block.
• 5,5 mm flat screwdriver –for removing the lamp insert.
• 30mmwrench -totightenthelocknutandthepressurenut.
• Hook screw key size 155-165 –to open/closing the front
ring.
MAINTENANCE INSTRUCTIONS
The luminaire should be inspected according to Company
routines. The manufacturer suggests regular check for
water intrusion/condensation which should be removed
immediately. Check the drain plug / drain hole function.
When cleaning, use only mild detergents. Alcohol or
petroleum based products may damage lens, paint or
plastic components.
APPLICATIONS
• Floodlighting of helicopter landing areas
• For use in hazardous areas
• Floodlighting
APPROVALS
Certificate No.: Nemko 00ATEX245
Complies with: EN 500014:1997 + A1:1999 + A2:1999
EN 50018:1994
EN 50019:1994
CSA
International, 216432
Canada
Complies with: CSA Standard C22.2 No 0-M91
CSA Standard C22.2 No 0.4-M1992
CSA Standard C22.2 No 43-M1984
CSA Standard C22.2 No 250.0-00
CAN/CSA Standard E60079-0:02
CAN/CSA Standard E60079-1:02
CAN/CSA Standard E60079-7:02
UL 1598-2000, First edition
UL 542-1999, Eight edition
UL 935-2001, Tenth edition
ANSI/UL 60079-0-2002, First edition
ANSI/UL 60079-1-2002, First edition
ANSI/UL 60079-7-2002, First edition

TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL
INSTALLATION INSTRUCTIONS
The floodlight should be installed according to the
calculated light distribution plan. The glass in front should
face the centre at the helideck, unless stated otherwise.
Secure the floodlight to the helideck by means of four M10
bolts.
Open the enclosure cover on rear. Replace cable gland
gaskets as required to match the cable diameter. Unused
cable glands should always be replaced with a blind plug.
Connect cables and replace the enclosure cover.
Exposed non-current carrying metal is to be bonded to
ground by a minimum 14 AWG (2,5mm²) copper wire.
RUBBER SEAL
Cable diameter Size Part No.
11 - 15mm Ø26,8/15,0x10mm 5002 0140
15 - 20mm Ø26,8/20,3x10mm 5002 0139
Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland,
also make sure to use the correct rubber seal when you install the luminaire
Front Side
Bottom

TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL
REPLACING XENON LIGHT BULB
Use front ring tool to loosen/screw off front ring,
anticlockwise.
Warning ! High voltage components inside lamp. Make sure to disconnect
power before opening.
Distance bracket
Distance bracket
Holding clip
Older version:
2. REMOVE HOLDING CLIP AND/OR DISTANCE
BRACKET
1. REMOVE FRONT RING
3. SLIDE OUT LAMP INSERT
Newer version:
Note: To be performed by Ex certified personnel
only

TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL
4a-1:
Disconnect the high voltage plug from the light bulb.
Position lamp removal tool over locking ring as shown
below. twist approx. 30 degrees anti-clockwise.
4a-2:
Remove xenon lamp
Xenon lamp
Locking ring
4b-1:
Disassemble the reflector unit. 3 x M4 screws
Disconnect the hight voltage plug.
4b-2:
Position lamp removal tool over locking ring as shown
below. Twist approx. 30 degrees anti-clockwise.
4b-3:
Remove xenon lamp
Locking ring
Xenon lamp
4A. REMOVE LIGHT BULB, NEW VERSION 4B. REMOVE LIGHT BULB, OLD VERSION
Note: make sure the new xenon bulb is clean. Do not touch the glass part of the bulb.
Mount lamp back together in reversed order.
5. INSERT NEW XENON BULB

TECHNICAL DATA
Material: Acid proof stainless steel. Safety glass
Input voltage: 254V AC 50/60Hz
230V AC 50/60Hz
110V AC 50/60Hz
Power consumption: 50Watt
IP-rating: IP 66/67 ( according to EN 60529)
Cable glands: M25, Increased safety, EEx`E`II
TAMB: ATEX: -20°C to +40°C
CSA: -20°C to +40°C
Area of use: Zone 1, Zone 2 and safe area
Weight: 11,5 kg.
TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL
SPARE PARTS
Part No.
Xenon Lamp, D2S. 35W, For TEF 9964 9400074
Front Glass 3120
High Voltage Igniter Unit Xenon 9400103
Locknut for Xenon D2S 9400108
Transformer W/ Mounting Bracket for 9964, 230/254 VAC 4386
Transformer W/ Mounting Bracket for 9964, 110 VAC 4387
Rectifier For 9964 Xenon Helideck Light 3069
Cable Gland Exe E204/622 M25/D kit 11,0-20,1 mm/9mm 6222502
Complete Insert for TEF 9964 230/254V 3173
Complete Insert for TEF 9964 110V 3249
Complete Insert for TEF 9964 24V 4210
Tool for Replacing Xenon Lamp in TEF 9964 Helideck Floodlight 4676
Tool for Helideck Lights 4627