Stairville DJLase150-RGY DMX User manual

User Manual
Thank you for using the Stairville DJLase series laser projector. For the
sake of safety and better operation of this projector, please read this manual
carefully before use and operate the projector , lest incur any personal injury
or damage to the projector.
Please check the local Laser assignments in your country
before starting the Laser Show!!!
DJLase150-RGYDMX

●Package list:
When you unpack the case , please take time to examine the items as follow:
1 pcs. Stairville DJLase 150 RGY DMX
1 pcs. Power cord 1
1 pcs. Owners manual
●Product Introduction:
Stairville DJLase 150 RGY DMX laser performer uses the latest muti-patterns laser control system
researched and developed by ourselves. It can control four different patterns with various effects
simultaneously. It adopts the latest appearance design to make it compact and light. The housing uses
the imported paint.
Stairville DJLase 150 RGY DMX laser performer adopts the semiconductor laser source. Laser
generator is double-temperature -controlled power supply. The laser light source has a long life span
and high stability, complying with the international standard.
It uses the latest low speed vibratory scanner system researched and developed by ourselves,
international DMX-512 signal control. There are 85 latest geometric laser patterns in it, as well as 26
pre-programmed 4patterns laser shows.It can make tunnel effect and animation, geometric, character
and three-dimensional effects, Laser sky effects, Rolling effects, Scanning effects, and Laser tunnel
effects in all directions with 5kpps vibratory mirror scanner system.
Control mode: DMX-512 signal control (with 16CH), music active, automatic run, master & slave control
mode. It can be applied for the place of public entertainment such as disco, night club, TV station and
theater etc.
●Instructions:
After unpacking, check whether the laser lighting has been damaged by transport such as any screw
loosening, lighting tube broken, etc. If everything is OK, select a proper location, hang the light and
adjust its angle properly, then connect the power cord and the ground wire before switch on at the
means.
This product belongs to grade-1 protective equipment. Notice that while using this laser lighting the
green and yellow wire has to connect the ground properly by professionals. Please examine the
electrics and voltage before power on it. Because of the radiate laser generator `s own characteristic
and to secure the laser `s long life span. Please terminate it for 10 minutes after using it for 30 minutes.
Avoid being interfered by other signals while controlled by Fire Phoenix software or using the DMX-512
signal controller, such as wireless interphone & high radiated source.
2

●Technical Parameters:
Rated voltage: AC110V /AC230V ±10％
Rated frequency: 50HZ~60HZ
Power consumption: 25 Watt
Laser power: 140mw
Laser source: solid semiconductor laser generator
Color: green/532nm, red/650nm
Laser patterns: 85 patterns
Scanning: 3~5kpps vibratory mirror scanner system
Scanning angle: ±20 degrees
Control Channel：16 DMX-512 signal control channels
Control signal: DMX-512 international standard signal
Control mode: DMX-512, music active, automatic run, master & slave
Cool system: fan
Operating environment: indoor
●Channel `s function
Stairville DJLase 150 RGY DMX use international standard DMX-512 signal control, with 16
channels, as the below detailed descriptions :
Channel
DMX-512 Value 0〜
255
Descriptions
CH1
Function choose
0〜50
Laser is off
51〜101
DMX pattern mode
102〜152
DMX SHOW edit mode
153〜203
DMX SHOW automatic run mode
204〜255
DMX SHOW music active mode
CH2
Multi-functions
Channel
1〜255
Pattern mode ：Pattern A
0〜255
SHOW mode ：Laser SHOW
CH3
Multi-functions
Channel
1~255
Pattern mode ：Pattern B
0~255
SHOW mode ：Laser SHOW segment
CH4
Pattern C
1~255
Pattern mode ：Pattern C
CH5
Pattern D
1~255
Pattern mode ：Pattern D
CH6
Multi-functions
Channel
0~51
At the same time with Pattern A、B、C、D
effects
52~103
Pattern A control effect
104~155
Pattern B control effect
156~207
Pattern C control effect
208~255
Pattern D control effect
0~255
1. 0 is the function with turning off laser
SHOW segment edit
1. 1~255 is the function with turning on
laser SHOW segment edit
3

CH7
Rotation effect
1~127
Rotation angle adjustment，the 15CH
adjustment speed
128~191
Counter-clockwise rotation
192~255
Clockwise rotation
CH8
Vertical turning
1~127
Vertical rotation linearity adjustment，15CH
adjustment speed
128~255
Vertical rotation speed adjustment
CH9
Horizontal
turning
1~127
Horizontal rotation linearity
adjustment，15CH adjustment speed
128~255
Horizontal rotation speed
CH10
Moving effect
1~127
Horizontal moving speed
128~255
Vertical moving speed
CH11
Gradual
drawing effect
0~41
gradual increasing drawing
42~83
gradual decreasing drawing
84~127
gradual increasing and decreasing
Point effect
128~255
Adjustment of point brightness
CH12
Vertical
1~255
Adjustment of vertical angle，
15CH adjustment speed
CH13
Horizontal
1~255
Adjustment of horizontal angle，
15CH adjustment speed
CH14
Zoom in/out
effect
1~127
Adjustment of pattern size，
15CH adjustment speed
128~169
Pattern from small to big ，
15CH adjustment speed
170~211
Pattern from big to small ，
15CH adjustment speed
212~255
Zoom patterns ，15CH adjustment speed
CH15
Control color
0~255
Choose different color effect, 15CH
adjustment speed
CH16
Speed
adjustment
0~255
CH11、CH12、CH13、CH14 effective
speed adjustment
4

●Signal Connection and Address Code Dialing
When the controller outputs the standard DMX512 signal, the connection of which is accomplished
through the “input” and “output” 3-pin XLR socket. When a console signal outputs to the unit, it must
correspond to the Pin 1 Ground, Pin 2 Negative and Pin 3 Positive of the XLR socket on the unit. If it
does not work just try exchanging the Pin 2 and Pin 3 (these 2 pins are generally do not need
exchanged for consoles). The signal wire length should not exceed 100m in order to avoid the
interference of the other signals by any other electric appliances.
This unit adopts the 3 pins XLR socket, detail connection of many units as bellow:
If your DMX-512signal controller adopt 5 pins XLR plug, you need one transfer line, the transfer
method as following:
5

When control signals from the console inputs into Stairville DJLase 150 RGY DMX projector. The
projector must be assigned a data start address code, so that a unit may act on the corresponding
control signal. Thus, when any controller is used, every unit must have its own data start address
Accordingly, the address of the first unit is set as 1, the second unit has also 16 channels, so its
address code is 17, the third unit is set at 33, so on and so forth (the setting method will also depend on
the specific console, the above is just for general cases).
Every binary system address code corresponding the decimal system number :
1
2
3
4
5
6
7
8
9
Number
1
2
4
8
16
32
64
128
256
n u m e r i c a l
value
Calculation formula : light adress code = ( the N light – 1 ) * the channel of light + 1
For example : the eighth light’s address code = ( 8 – 1 ) * 16+1=113,the
corresponding binary system code : the second, fourth, sixth, seventh is ON, and the other is OFF.
The details of DMX-512 signal control mode address switch as follow:
Lamp
no.
Start
address
Control switch (ON)
1
1
1
2
17
1、5
3
33
1、6
4
49
1、5、6
5
65
1、7
6
81
1、5、7
7
97
1、6、7
8
113
1、5、6、7
9
129
1、8
10
145
1、5、8
┇
┇
┇
Stairville DJLase 150 RGY DMX Laser Performer has controlled by on/off switch address code. 1 to 9 are
the numerical value DMX 512 signal, 10 is the exchange switch of sound active control, automatic run,
master & slave and DMX512 signal control.
The detailed control mode as follow:
MODE
Control switch (ON)
1
DMX-512 signal control mode
10 : ON，1-9 : address code
2
music active mode、master mode
1 : ON，others : OFF
3
automatic run mode、master mode
1-10 : OFF
4
Slave mode
10:ON, 1-9:OFF
6

The skill of editing various patterns with DMX-512:
1. Pattern A、B、C、D’s channel is controlled dividually, you can turn on or off, exchange pattern
arbitrarily, it’s very convenient to use.
2. When the CH2、CH3、CH4、CH5’s channel address is 0, it will turn on the pattern
A、B、C、D。
3. The four pattern’s effects controlling channel is used doublely, it is exchanged by CH6:
When the CH6 is 0~51, the pattern is A、B、C、D simultaneously, When the CH6 is 52~103, the
pattern is A, When the CH6 is 104~155, the pattern is B, When the CH6 is 156~207, the pattern is
C, When the CH6 is 208~255, the pattern is D.
Edit the DMX-512 inside laser show segment:
1、CH2 choose laser SHOW, CH3 choose the SHOW segment needed to edit, when CH6 is 0, it will
turn off SHOW segment edit , when CH6 is 1~255, it will turn on SHOW segment edit.
2、When CH6 is 1~51, the pattern is A、B、C、D control simultaneously , When CH6 is 52~103, the
pattern is A, When CH6 is 104~155, the pattern is B, When CH6 is 156~207, the pattern is C, When
CH6 is 208~255, the pattern is D.
Pay attention to bellow descriptions for the master & slave control mode :
1. You can not connect to the DMX-512 controller when the master and slave projector are operating
synchronously, otherwise the master and slave synchronous functions can’t be realized;
2. When operating the master and slave controlling, it must be only one master projector, otherwise it
can not be operated synchronously.
Master and Slave connection as bellow:
7

●Safety marks:
！Please make sure to switch off the power before installation or maintenance.
！Please keep the fan expedite and environment ventilated.
！This laser projector is designed for the indoor, so while using, please avoid any dripping. If you
want to use for outdoor, please do enough waterproof measure.
！Before maintenances, please refer to eligible personnel
！Do not use any power voltage and light type of different specifications
！Please do not see the laser light directly, in case it might damage the eyes。
！Avoid electric shock! Bulb overheating。
！Do not use it frequently under the humid atmosphere。
●Maintenance:
It is very important to keep the Stairville DJLase 150 RGY DMX laser light clean, therefore please clean
reflector lens monthly to keep the lights away from dust, dirt or fog juice. We suggest that clean the light
with professional glass cleaning lotion and downy cloth. Keep the light clean regularly will not only
maintain the maximum laser output brightness but also will extend the life span of the laser.
all Copyrights by:
Musikhaus Thomann
Treppendorf 30
GER- 96138 Burgebrach
Tel.: [phone]
[email protected]
www.thomann.de
8