Stamina InMotion E3000 User manual

When calling for parts or
service, please specify
the following number :
Model#: 55-1616
CAUTION:
Weight on this product should not exceed 250 lbs.
This Product is Produced Exclusively by
2040 N. Alliance, Springeld, MO 65803
Customer Service
1 [phone]
www.staminaproducts.com
Product May Vary Slightly From Pictured.
!WARNING !
Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.
STAMINA PRODUCTS
MADE IN CHINA
© 2010 Stamina Products, Inc.
2010, 08
Owner’s Manual

TABLE OF CONTENTS
Safety Instructions ...................................... 2
Before You Begin ........................................ 4
Equipment Warning & Notice Labels ........ 5
Hardware Identication Chart .................... 6
Assembly Instructions ................................ 7
Set Up Instructions ................................... 9
Operational Instructions ........................... 10
Storage ....................................................... 11
Maintenance ............................................... 11
Conditioning Guidelines ........................... 12
Warm-Up and Cool-Down ......................... 13
Product Parts Drawing .............................. 14
Parts List .................................................... 15
Warranty ..................................................... 17
Notes ........................................................... 18
Fax/Mail Ordering Form ............................ 19
SAFETY INSTRUCTIONS
2
1. Read all warnings posted on the InMotion® E3000.
2. The InMotion® E3000 should only be used after a thorough review of the Owner’s Manual.
3. We recommend that two people be available for assembly of this product.
4. Keep children away from the InMotion® E3000. Do not allow children to use or play on the InMotion®
E3000. Keep children and pets away from the InMotion® E3000 when it is in use.
5. It is recommended that you place this exercise equipment on an equipment mat.
6. Set up and operate the InMotion® E3000 on a solid level surface. Do not position the InMotion®
E3000 on loose rugs or uneven surfaces.
7. Make sure that adequate space is available for access to and around the InMotion® E3000.
8. Before using, inspect the InMotion® E3000 for worn or loose components, and securely tighten or
replace any worn or loose components prior to use.
9. Consult a physician prior to commencing an exercise program. If, at any time during exercise, you
feel faint, dizzy, or experience pain, stop and consult your physician.
10.Followyourphysician’srecommendationsindevelopingyourownpersonaltnessprogram.
11.Alwayschoosetheworkoutwhichbesttsyourphysicalstrengthandexibilitylevel.Knowyour
limits and train within them. Always use common sense when exercising.
12. Do not wear loose or dangling clothing while using the InMotion® E3000.
13. Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or
crosstrainingshoes.Besurethattheytwell,providefootsupportandfeaturenon-skidrubbersoles.
14. Be careful to maintain your balance while using, mounting, dismounting, or assembling the InMotion®
E3000, loss of balance may result in a fall and serious bodily injury.
15. To maintain your balance, always mount or dismount the InMotion® E3000 from the lowest foot
pedal. Refer to the detail instructions on page 10.
16.Keepbothfeetrmlyandsecurelyonthepedalcapswhileexercising.
17. The InMotion® E3000 should not be used by persons weighing over 250 pounds.
18. The InMotion® E3000 should be used by only one person at a time.
19. The InMotion® E3000 is for consumer use only. It is not for use in public or semipublic facilities.
!WARNING:
This equipment is for home use only. Do not use in institutional or commercial
applications. Failure to follow this warning could result in death or serious injury.
!WARNING: This product contains a chemical known to the State of California to cause
cancer and birth defects or other reproductive harm.
!WARNING: To reduce the risk of serious injury, read the following Safety Instructions
before using the InMotion® E3000.
WARNING: Before starting any exercise or conditioning program you should consult with your personal physician
to see if you require a complete physical exam. This is especially important if you are over the age of 35, have never
exercised before, are pregnant, or suffer from any illness. READ AND FOLLOW THE SAFETY PRECAUTIONS.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.
!

THANK YOU FOR PURCHASING THE
InMotion® E3000
To help you get started, we have pre-assembled most of your
InMotion® E3000 at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 [phone]
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springeld, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[email protected]
www.staminaproducts.com
3
Call Us First
www.staminaproducts.com
1(800) 375-7520
Customer Service

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench
Allen Wrench (6mm)
Thank you for choosing the InMotion® E3000.
We take great pride in producing this quality
product and hope it will provide many hours of
quality exercise to make you feel better, look
better, and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The InMotion® E3000
provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.
Read this manual carefully before using the
InMotion® E3000.
BEFORE YOU BEGIN
Although Stamina constructs its products with
thenestmaterialsandusesthehigheststandards
of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your InMotion® E3000,
please do not return the product. Contact us
FIRST!
If a part is missing or defective, please call
us toll free at 1-800-375-7520 (in the U.S.). Our
Customer Service Staff is available to assist you
from7:30A.M.to5:00P.M.(CentralTime)Monday
through Thursday and 8:00 A.M. to 3:00 P.M.
(CentralTime)onFriday.
If you would like to contact us online, go to our
website at www.staminaproducts.com and access
the Customer Service section.
Be sure to have the name and model number of
the product available when you contact us.
4
Crank
Base Board
Right Pedal Cap
Right Cover
Left Pedal Arm
Roller
Tension Knob
Meter
Oval Endcap
Left Pedal Cap
Main Frame
Rear Stabilizer
Oval Endcap
Warning Label
Upright
Handlebar
Foam Grip
Foam Grip
Handlebar Post
Adjustment Knob

Label is larger than actual size
This chart is provided to help identify the warning and notice labels on the InMotion® E3000.Please
take a moment to familiarize yourself with all of the warning and notice labels.
EQUIPMENT WARNING & NOTICE LABELS
WARNING LABEL(55)W1
5

Part Number and Description Qty
This chart is provided to help identify the hardware used in the assembly process. Place the washers or
theendsoftheboltsorscrewsonthecirclestocheckforthecorrectdiameter.Usethesmallscaleto
check the length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
length
length
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.
HARDWARE IDENTIFICATION CHART
6
mm.
in.
INCHES
MILLIMETERS
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6
6 8 10 12
3/16" 1/4" 5/16" 3/8" 1/2"
42 Carriage Bolt (M10 x 1.5 x 43mm) 2
45 Bolt, Button Head (M8 x 1.25 x 20mm) 4
59 Bolt, Button Head (M8 x 1.25 x 16mm) 6
49 Nylock Nut (M6 x 1) 2
51 Nylock Nut (M10 x 1.5) 2
76 Arc Washer (M6) 2
77 Arc Washer (M8) 4
75 Bolt, Hex Head (M6 x 1 x 33mm) 2

Placeallpartsfromtheboxinaclearedareaandpositionthemontheoorinfrontofyou.Remove
all packing materials from your area and place them back into the box. Do not dispose of the
packing materials until assembly is completed. Read each step carefully before beginning. If you
are missing a part please call our toll-free number for assistance 1-800-375-7520 or e-mail us at
[email protected].
ASSEMBLY INSTRUCTIONS
7
STEP 1
Attach the REAR STABILIZER(2) to the MAIN FRAME(1) with CARRIAGE BOLTS(M10x1.5x43mm)
(42) and NYLOCK NUTS(M10x1.5)(51).
STEP 2
Attach the BASE BOARD(37) to the MAIN FRAME(1) with the STANDS(40) and BUTTON HEAD
BOLTS(M8x1.25x16mm)(59).
STEP 3
Attach the LEFT PEDAL CAP(33) to the LEFT PEDAL ARM(3) with BUTTON HEAD BOLTS
(M8x1.25x20mm)(45). Repeat on the other side.
NOTE: The LEFT and RIGHT PEDAL CAPS(33, 34) have a raised lip on three sides. Attach the LEFT
and RIGHT PEDAL CAPS(33, 34) to the LEFT and RIGHT PEDAL ARMS(3, 4) so that the side
without the raised lip is on the outside.

ASSEMBLY INSTRUCTIONS
STEP 4
Insert the UPRIGHT(68) into the MAIN FRAME(1) and secure with BUTTON HEAD BOLTS
(M8x1.25x16mm)(59) and ARC WASHERS(M8)(77).
STEP 5
Insert the HANDLEBAR POST(71) into the UPRIGHT(68), and lock it in one of the adjustment holes with
ADJUSTMENT KNOB(69).
NOTE: There are three adjustment holes on the HANDLEBAR POST(71) for adjusting the height of the
HANDLEBAR(72).
STEP 6
Refer to the detail view A. Note the correct position of the HANDLEBAR(72), the HANDLEBAR(72)
should be assembled with a six degrees angle forward than the HANDLEBAR POST(71).
Attach the HANDLEBAR(72) to the HANDLEBAR POST(71) with HEX BOLTS(M6x1x33mm)(75), ARC
WASHERS(M6)(76), and NYLOCK NUTS(M6x1)(49). The HEX BOLTS(M6x1x33mm)(75)tinsidethe
hex-shapedholesintheHANDLEBAR POST(71).
8
hex-shaped
hole
A.

LEVELING: Adjust the location of InMotion® E3000 to ensure InMotion® E3000 sits on the floor
without rocking.
MOVING: Grasp the REAR STABILIZER(2) and HANDLEBAR(72) to move the InMotion® E3000.
Do not use the PEDAL ARMS(3,4) to move the InMotion® E3000.The PEDAL ARMS(3,4)
willmoveandmaypinchyourhandorngers.
FUNCTION INSPECTION:
Visually inspect the InMotion® E3000 to verify that assembly is as shown in the above illustration. Check
the function of the InMotion® E3000. Stand on the foot pedals. Slowly move your highest foot forward
and follow the natural path of the machine. Turn the crank slowly through one complete revolution to verify
that the drive train functions properly. Adjust the TENSION KNOB(21) and verify that it functions properly.
CAUTION: Locate and read the WARNING LABEL(55) on the InMotion® E3000.Make sure that all
users read the WARNING LABEL(55).
SET UP INSTRUCTIONS
9
Equipment Mat
Place the InMotion® E3000 in the area where it will be used. It is recommended that the InMotion®
E3000 be placed on an equipment mat. The maximum operation dimensions of the InMotion® E3000 are
approximately30.2incheslongx18.5incheswidex48.8inchestall.(Thesedimensionsmayvaryupto
oneinch.)Anarea4feetwidex4.5feetlongisrequiredforsafeoperationoftheInMotion® E3000. Make
sure that adequate space is available for access to and passage around the InMotion® E3000.

OPERATIONAL INSTRUCTIONS
10
USING THE FITNESS METER
POWER OFF:
Automatically scans TIME, DISTANCE, COUNT, and CALORIES in sequence with a change
every six seconds. Press and release the button until “SCAN” appears on the display.
Displays the time from one second up to 99:59 minutes.
Displays the distance from zero to 999.9 miles.
Displays the total number of strides you have taken from zero to 9999 strides.
Displays the calorie consumption from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
Automatic shut off after four minutes of inactivity.
POWER ON:
FUNCTIONS:
SCAN:
TIME:
DISTANCE:
COUNT :
CALORIES:
FUNCTION BUTTON:
Press and release to select functions.
Press and hold for four seconds to reset all functions to zero.
Pedal movement or press the button.
The meter will shut off automatically after four minutes of inactivity. All function values will
be kept. Push the button and hold it down for four seconds to reset all functions to zero.
NOTE:
BATTERY
The meter operates with a 1.5v LR44 alkaline battery. Replace the battery when you see inconsistencies
in the display.
1. To maintain your balance, always mount or dismount the InMotion® E3000 from the lowest foot pedal,
refer to the following illustrations. Loss of balance may result in a fall and serious bodily injury.
2. Grasp the HANDLEBAR(72) with both hands to help to maintain your balance while using the InMotion®
E3000 until you are familiar with the InMotion® E3000.
PRECAUTIONS FOR USING
CORRECT INCORRECT

OPERATIONAL INSTRUCTIONS
11
EXERCISE WORKOUT
To start using the InMotion® E3000 simply stand on the foot pedals with the front of your shoes close to
the front edge of the pedal cap. Move your highest foot forward and follow the natural path of the machine.
For more stability, hold on to the HANDLEBAR(72) while stepping onto and off of the pedals. Start on a load
level that is comfortable until you are familiar with the machine. Once you are familiar with the elliptical and
comfortable with the resistance, adjust the load level as described below to achieve the workout desired.
FORWARD AND REVERSE
The InMotion® E3000 can be used in forward and reverse directions to vary the muscles that you work.
This will help you to stay motivated and achieve the best results. To change directions, simply slow the
pedals down until they stop, then pedal in the opposite direction.
LOAD LEVEL ADJUSTMENT
The load level of InMotion® E3000 can be changed at any time during
your workout. Adjusting your load level will allow you to increase or
decrease your intensity level.
To increase the load, turn the TENSION KNOB(21) clockwise. To
decrease the load, turn the TENSION KNOB(21) counterclockwise.
STORAGE
1. To store the InMotion® E3000 simply keep it in a clean dry place.
2. The minimum rest dimensions of the InMotion® E3000 are approximately 29.2 inches long x 18.5 inches
wide x 45 inches tall. These dimensions may vary. Please measure your InMotion® E3000 if exact
dimensions are needed.
3. Grasp the REAR STABILIZER(2) and HANDLEBAR(72) to move the InMotion® E3000.Do not use
the PEDAL ARMS(3,4) to move the InMotion® E3000.
The safety and integrity designed into the InMotion® E3000 can only be maintained when the
InMotion® E3000 is regularly examined for damage and wear. Special attention should be given to the
following:
MAINTENANCE
NOTE: A standard crank extractor tool is required to remove the CRANKS(28) from the AXLE(9).
1. Adjust the TENSION KNOB(21) and verify that the Flywheel System provides tension. The Flywheel
System should provide many years of use.
2. Verify that the WARNING LABEL(55) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement WARNING LABEL(55) if it is missing or damaged.
3. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
4. Worn or damaged components shall be replaced immediately or the InMotion® E3000 removed from
service until repair is made.
5. Only Stamina Products supplied components shall be used to maintain/repair the InMotion® E3000.
6. Keep your InMotion® E3000 clean by wiping it off with an absorbent cloth after use.

How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise
so you don't tire too quickly.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or
threengersonyourwristandtakeasixsecondheartbeatcount.Multiply
theresultsbytentondyourheartrate.Forexample,ifyoursixsecond
heartbeat count is 14, your heart rate is 140 beats per minute. A six second
count is used because your heart rate will drop rapidly when you stop
exercising. Adjust the intensity of your exercise until your heart rate is at the
proper level.
wrist pulse
Remember to follow these essentials:
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
 Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity)to90%(higherintensity)ofyourmaximumheartratezone.Startatthelowerintensity,and
builduptohigherintensityasyoubecomemoreaerobicallyt.
If you feel dizzy or lightheaded you should slow down or stop exercising.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table
below. For effective aerobic exercise, your heart rate should be maintained at a level between 60%
and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of
your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your
workout by increasing your heart rate.
CONDITIONING GUIDELINES
Target Heart Rate Zone Estimated by Age*
* For cardiorespiratory training benefits, the American College of Sports Medicine recommends
working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the
maximumheartrate,thefollowingformulawasused:220-Age=predictedmaximumheartrate
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Average Maximum
Heart Rate 100%
Age
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate)
12

WARM-UP and COOL-DOWN
Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries.
Warm up for two to ve minutes before strength training or aerobic exercising. Perform activities that
raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging,
jumping jacks, jump rope, and running in place
Stretching    Stretching while your muscles are warm after a proper warm-up and again after your
strength or aerobic training session is very important. Muscles stretch more easily at these times
because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held
for 15 to 30 seconds. Do not bounce.
Suggested Stretching Exercises
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting
stateattheendofeachexercisesession.Apropercool-downslowlylowersyourheartrateandallows
blood to return to the heart.Your cool-down should include the stretches listed above and should be
completed after each strength training session.
Lower Body Stretch
Placefeetshoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DONOTBOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
Whilesittingontheoor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DONOTBOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Over Leg Stretch
Standwithfeetshoulder-
width apart and lean forward
asillustrated.Usingthe
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DONOTBOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to
the left leg. Do this stretch
several times slowly.
Bent Torso Pulls
Whilesittingontheoor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent, and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.
13

PRODUCT PARTS DRAWING
14
FRONT
BACK

PART# PART NAME QTY
1 Main Frame 1
2 Rear Stabilizer 1
3 Left Pedal Arm 1
4 Right Pedal Arm 1
5 Pulley 1
 6 Bearing(6003) 2
7 Pulley Spacer 1
 8 CRing(16mm) 4
9 Axle 1
 10 V-RibbedBelt 1
11 Flywheel 1
 12 Bearing(6000) 2
13 Bearing Spacer 1
14 Flywheel Spacer 1
15 Spacer Cap 2
 16 FlywheelShaftBolt(M10x1.5x82mm) 1
17 Eyebolt 1
18 Tension Bracket 1
19 Brake Brace 1
20 Spring 1
21 Tension Knob 1
22 Meter 1
23 Sensor Wire 1
24 Magnet 1
 25 SquarePlug(25mmx25mm) 1
26 Left Cover 1
27 Right Cover 1
28 Crank 2
 29 FlangeBolt(M8x1.25x15mm) 2
30 Crank Spacer 2
 31 LargeWasher(16.3x24mm) 4
32 Pedal Arm Bushing 4
33 Left Pedal Cap 1
34 Right Pedal Cap 1
 35 SquarePlug(30mmx30mm) 2
36 Roller 2
37 Base Board 1
38 Left Foam Pad 1
39 Right Foam Pad 1
40 Stand 2
 41 OvalEndcap(30mmx60mm) 2
 42 CarriageBolt(M10x1.5x43mm) 2
 43 Bolt,ButtonHead(M6x1x13mm) 3
 44 Bolt,ButtonHead(M6x1x17mm) 2
 45 Bolt,ButtonHead(M8x1.25x20mm) 4
 46 Bolt,ButtonHead(M8x1.25x42mm) 2
 47 Screw,RoundHead(M3.4x8mm) 2
PARTS LIST
15

 48 Screw,RoundHead(M4x25mm) 10
 49 NylockNut(M6x1) 11
 50 NylockNut(M8x1.25) 2
 51 NylockNut(M10x1.5) 3
 52 Nut(M10x1.5) 1
 53 Washer(M10) 1
 54 WavyWasher(M16) 2
55 Warning Label 1
56 Wrench 1
 57 AllenWrench(6mm) 1
58 Manual 1
 59 Bolt,ButtonHead(M8x1.25x16mm) 6
 60 WavyWasher(M17) 1
 61 CRing(17mm) 1
62 Pu Bushing 1
 63 SquarePlug(38mmx38mm) 1
64 Crank Cap 2
65 Large Tension Bracket 2
66 Double Eyebolt 1
67 Stabilizer Stand 1
 68 Upright 1
69 Adjustment Knob 1
70 Sleeve 1
71 Handlebar Post 1
72 Handlebar 1
73 Foam Grip 2
 74 RoundPlug(25.4mm) 2
 75 Bolt,HexHead(M6x1x33mm) 2
 76 ArcWasher(M6) 2
 77 ArcWasher(M8) 4
PART# PART NAME QTY
PARTS LIST
16

LIMITED WARRANTY
WARRANTY
MODEL 55-1616
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and one year on
the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL
NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,
MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY
REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED
BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health
clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the
product'suseisinfurtheranceofaprotmakingenterprise,andallotherusewhichisnotforpersonal,
family, or household purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at [email protected], or
call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to
return the product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH
OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE
DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR
BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER
DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF
ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY
IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY
AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any
implied warranty, the Warrantor reserves the right to require the product to be returned for inspection,
atthepurchaser'sexpense,totheWarrantor'spremisesinSpringeld,Missouri.Returnoftheenclosed
warranty registration card is not required for warranty coverage, but is merely a way of establishing the
date and place of purchase.
Stamina Products, Inc. SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS
OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY
IMPLIED WARRANTY.
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This
warrantygivesyouspeciclegalrights,andyoumayalsohaveotherlegalrightswhichvaryfromstate
to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods
to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.
If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied
warranties and consequential and incidental damages with respect thereto shall be disregarded and shall
be deemed not to have been made to the extent necessary to comply with such legal restriction.
17

NOTES
18

IMPORTANT : Before lling out the form below make sure you have the right information.
Refer to the parts list to make sure you're ordering the right parts!
Detach and Mail or Fax the Form Below
Stamina Products, Inc.
P.O. Box 1071
Springeld, MO 65801-1071
IMPORTANT : We must have your phone number in order to process the order!
Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reachedbyemailat[email protected]ortollfreeat1-800-375-7520(intheU.S.).
Should a part be missing or a defective part found, please call us from 7:30 A.M. to 5:00 P.M. Central
Time,MondaythroughThursdayand8:00A.M.to3:00P.M.onFridayorlloutthefaxsheetordering
formbelowandfaxitto[phone].OurCustomerServiceDepartmentwillbeabletoassistyouwith
your problem and the part will be mailed directly to your house.
Mr./Ms:
Address: Apt. #:
City: State: Zip Code:
Phone#:()    WorkPhone#:()
Date Purchased:
Model #:
Purchased From:
 PART # DESCRIPTION QUANTITY
 1 Rear Unit Assembly 1
EXAMPLE:
FAX/MAIL ORDERING FORM
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springeld, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[email protected]
www.staminaproducts.com