Standard Furniture 14140 User manual

Read instruction carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment. Remove all components from
pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts as specified below.
It is recommended to use two or more person during the assembly process.
ASSEMBLY INSTRUCTION
GROUP NO.: 14140 CABANAS DR
ITEM NO.: 14141 - DINING TABLE W/18' LEAF
HARDWARE LIST: PART LIST:
No. Description Sketch Qty'
1Long Bolt
Size
ɸ516'' x 50mm 4pcs
3
4
Lock Washer ɸ516'' x 13mm 12pcs
5
Big Flat
Washer ɸ516'' x 19mm 8
pcs
6
Allen Key 4 mm7 1
pc
No. Description Sketch Qty'
Table'sScrew 12
pcs4mm x 30mm
Small Flat
Washer ɸ516'' x 12mm 4
pcs
ATable Top 1 pc
CTable Leg 2 pcs
Made in Vietnam
Cleaning instructions: Clean using soft cloth
Step 1 Step 2
Step 2: Attach the Mounting Plate (E) to the assembly base
in Step 1 by using Short Bolt (2), Lock Washer (3), Big Flat
Washer (4) and fully tighten with Allen Key (7). Do not over
tighten.
Step 3: Place the Table Top (A) upside down on a piece of
cloth or carpet to prevent finish from scratching. Aligning
the Wood Dowel on the Mounting Plate (E) to the pre-drilled
hole on the table slide of Table Top (A). Attach the assembly
Base in step 2 to the Table Slide of the Table Top (A) by
using Table's Screw (6) and fully tighten with Phillips-head
screw driver (not provided).
Step 3
FWood Plug Decor 2 pcs
Step 4: Turn the Table to upright position and fully tighten all
Bolts and Screws. Attach Wood Plug Decor (F) to the Table Leg
(C) by aligning the Wood Dowel of the Wood Plug Decor (F) to
the pre-drilled hole out side of Table Leg (C).
Unlock the Latch and pull the Table Top (A) from both ends.
Insert Table Leaf (B) to the middle of Table Top (A), close the
Table Top (A) by pushing from both ends. Lock the latch to
prevent from sliding. Assembly product is now completed.
Step 4
STANDARD
furniture
2Short Bolt ɸ516'' x 40mm 8pcs
DStretcher Support 1 pc
Wood
Dowel
7135
Step 1: Align the Wood Dowel of the Stretcher Support (D)
to the middle hole on the Table Leg (C). Attach 2 Table Legs
(C) to the Stretcher Support (D) by using Small Flat Washer
(5), Lock Washer (3) and Long Bolt (1) with Allen Key (7).
Do not fully tighten.
C
D
CC
C
D
EMounting Plate 1 pc
7
2
3
4
CD
E
C
C
E
Wood
Dowel
Hole
LOCK
UNLOCK
6
E
F
BTable Leaf 1 pc
A
B
E

Read instruction carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment. Remove all components from
pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts as specified below.
It is recommended to use one person during the assembly process.
HARDWARE LIST: PART LIST:
No. Description Sketch Qty'
1Long Bolt
Size
ɸ
14'' x 75mm 4
pcs
2Short Bolt ɸ
14'' x 40mm
3Lock Washer ɸ516'' x 13mm
3 pcs
11 pcs
4Flat Washer ɸ516'' x 19mm 11 pcs
5 Hex Nut ɸ516'' x 12mm 4 pcs
6Allen Key 1 pc4 mm
7Open Wrench 1 pc12 mm
No. Description Sketch Qty'
AChair Back 1 pc
BSeat Cushion
Frame 1
pc
CLeft Front Leg
Made in Vietnam
Cleaning instructions: Clean using soft cloth
8Chair'sScrew 4 pcs4 mm x40 mm
stickerstickunderstretcher
stickerstickunderstretcher
D
E
F
Right Front Leg
LeftSideStretcher
RightSideStretcher
1 pc
1 pc
1 pc
1 pc
Step 1 Step 2
Step 1: Attach Seat Cushion Frame (B) to Chair Back (A)
by securing the Flat Washer (4), Lock Washer (3), Short Bolt
(2) on back rail and Long Bolt (1) onto Corner with Allen
Key (6). Do not fully tighten.
Step 2: Attach the Left and Right Front Legs (C);(D) to seat
frame using Flat washer (4), Lock washer (3) and Hex nut (5)
by using Open Wrench (7) (do not fully tighten). Attach the
Left & Right side of Stretcher (E);(F) to left and right of
Front Leg and Chair back by securing the Chair's Screw (8)
with Phillips screw drivers (not provided).
Step 3
Step 3: Place the chair on flat surface and adjust legs so
that chair is level and does not wobble.Tighten all Bolts and
Hex nut with Allen key (6) and Open Wrench (7) provided.
Assembly product is completed .
7
5 3 4
R
L
D
8
ASSEMBLY INSTRUCTION
GROUP NO.: 14140 CABANAS DR
ITEM NO.: 14144 - DINING SIDE CHAIR
STANDARD
furniture
2
3
4
6
6
134
Right Front Leg (D)
Right side Stretcher (F)
"R" sticker stick under
stretcher
LeftFront
Leg(C)
LeftsideStretcher(E)
"L" sticker stick
under stretcher
B
A
Read instruction carefully prior to assembly.
pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts as specified below.
It is recommended to use one person during the assembly process.

Read instruction carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment. Remove all components from
pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts as specified below.
It is recommended to use one person during the assembly process.
HARDWARE LIST: PART LIST:
No. Description Sketch Qty'
1 Hex Nut
Size
ɸ516'' x 12mm 8
pcs
2Allen Bolt ɸ
14'' x 40mm
3Lock Washer ɸ516'' x 13mm
4 pcs
12 pcs
4Big Flat Washer ɸ516'' x 19mm 8 pcs
5ɸ
14'' x 12mm 4
pcs
6Allen Key 1 pc4 mm
7Open Wrench 1 pc12 mm
No. Description Sketch Qty'
ABench Cushion
Frame 1
pc
BLeft Front Leg or
Right Back Leg 2
pcs
Made in Vietnam
Cleaning instructions: Clean using soft cloth
8Bench'sScrew 4 pcs4 mm x45 mm
Step 1 Step 2
Step 3
ASSEMBLY INSTRUCTION
GROUP NO.: 14140 CABANAS DR
ITEM NO.: 14145 - BENCH
STANDARD
furniture
CRight Front Leg or
Left Back Leg 2
pcs
DSide Stretcher 2
pcs
ECenter Stretcher 2
pcs
7
134
B
B
B
C
C
D
D
A
8
Step 1: Attach the Left Front Leg / Right Back Leg (B) and Right
Front Leg / Left Back Left (C) to Bench Cushion Frame (A) by
securing the Big Flat Washer (4), Lock Washer (3), Hex Nut (1)
and OpenWrench (7). Do not fully tighten. Attach Side Stretcher
(D) to the middle of 2 Legs (B),(C) by using Bench 's Screw (8)
and tighten with Phillips screw drivers (not provided)
6
235
Small Flat Washer
D
A
E
B
D
B
E
C
E
5
3
26
Step 2: Attach Center Stretcher (E) to the Support Bar of Bench
Cushion Frame (A) and to the Side Stretcher (D) by securing the
Small Flat Washer (5), Lock Washer (3), Allen Bolt (2), tighten
with Allen Key (6). Do not fully tighten.
C
Step 3: Place the Bench on flat surface and adjust legs
so that Bench is level and does not wobble. Tighten all
Bolts and Hex nut with Allen key (6) and Open Wrench
(7) provided. Assembly product is completed.