Kesseböhmer DISPENSA VVS Series User manual

KESSEBÖHMER l 1 l 2 l 3 l 4 l 5
HANDLING INSTRUCTIONS
for DISPENSA VVS-x
Front connector
(inside)
Pull-out components:
■ Top runner
■ Support frame
■ Trays or baskets
■ Front panel connector
■ Bottom runner
■ Top damper (optional)
■ Bottom damper (optional)
■ Follower with Synchro lever
Support frame Trays or
baskets
Top damper
Top runner
(with stop point)
Stop point
Bottom damper
Bottom runner
Problem Possible cause Possible solution (summary) Full information
1. Shifted segment; Synchromatic defective. Replace follower with Synchro lever. 1.1
2. Bottom runner dirty. Clean the runner. (No oil!) 1.2
3. Connection between support frame
and bottom runner is loose.
Check the connection between the frame and the
bottom runner and tighten if necessary. 1.3
4. Bottom damper is unlatched. Push the front panel against the cabinet until you
hear the damper mechanism engage. 1.4
1. Door will not close
completely
5. Are the screws tight? Are you using the correct
screws?
1. Tighten screws.
2. Use the correct screws. 1.5
6. Are the top/bottom runners correctly
positioned? Position top/bottom runners correctly. 1.6
7. Has the cabinet been assembled correctly?
a) Is it vertical and level? (b) Is the fifth foot
correctly positioned for cabinet widths >40 cm?
(a) Align the cupboard so it is plumb and level.
(b) Position fifth foot correctly and adjust until
cabinet is level.
1.7 1.7 (a) 1.7 (b)
2. Pull-out makes a noise
during opening and closing
1. Bottom runner dirty. Clean the runner. 2.1
2. Is fifth foot correctly positioned for cabinet
widths >40 cm? Install and adjust fifth foot. 2.2
3. No soft close damping
(with option installed) 1. Is the top damper installed? Install the damper. 3.1
2. Is the top damper locked in place? Push the damper forward until it locks in place. 3.2
02/2012
Follower with Synchro lever

KESSEBÖHMER l 1 l 2 l 3 l 4 l 5
||
||
HANDLING INSTRUCTIONS
for DISPENSA VVS-x
1. Pull-out will not close completely
1.1 Shifted segment: Synchromatic defective
1.2 Bottom runner dirty (due to dirt, foreign particles, lubricant)?
Clean rollers and
running surfaces!
There must be no dirt on the bottom runner, especially the base element:
Wipe dry dirt off with a dry cloth. If there is oil or grease on the runner,
you will need to clean the whole element (running surfaces, roller surfaces
and rollers), e.g. with glass cleaner. The runner may need to be replaced.
Never use oil or other lubricants on the segments!
Open once completely!
No oil Clean
For Synchromatic to work correctly,
all components must be present
and correctly installed.
Follower
with Synchro
lever
Synchro
bolt Synchro tab

KESSEBÖHMER l 1 l 2 l 3 l 4 l 5
HANDLING INSTRUCTIONS
for DISPENSA VVS-x
1.4 Bottom damper (optional) unlatched
If the bottom damper is in the wrong position, reactivate the function by pushing the front panel against the
cabinet until you hear the mechanism engage. Alternatively, push the damper mechanism manually back into
position.
Correct positionIncorrect position
1.5 Are the screws tight? Are you using the correct screws?
1.3 Faulty connection between the pull-out frame and bottom runner
Check that the pull-out frame is correctly positioned on the bottom runner!
Incorrect position
1. Do not overtighten the screws!
2. The screws used must not come into contact with the middle slide!
3. The screws must be straight and firmly tightened (check the middle slide for signs of wear!)
Correct position
1. Do not use a cordless screwdriver! 2. The green locking pin must click into position and be fully visible.
Locking pin

61
253
==
32
34 386
450
482
2+3
==
93
!
!
a. b. c.
4
5
61
253
==
32
34 386
450
482
2+3
==
93
!
!
a. b. c.
4
5
1.
2.
!
!
1.
2.
!
!
KESSEBÖHMER l 1 l 2 l 3 l 4 l 5
HANDLING INSTRUCTIONS
for DISPENSA VVS-x
1.7 Has the cabinet been assembled properly?
a) Is the cabinet vertical and level?
Cabinet vertical and
level?
1.6 Are the runners mounted parallel (i.e. drilling positions correct)?
Top runner parallel to side panel? Bottom runner parallel to side panel?
Fifth foot correctly installed for cabinets 40 cm and wider?
For cabinets 40 cm and wider, check that the fifth foot is positioned centre front and has been correctly
adjusted/tightened. If the foot is not correctly installed, the bottom panel may sag, causing problems with
closing.
Fifth foot for cabinet widths 40 cm and wider
1. The side panels must be straight and vertical.
2. The bottom panel must be horizontal.
3. The cabinet must be fixed securely to the wall.

1.
2.
!
!
1.
2.
!
!
KESSEBÖHMER l 1 l 2 l 3 l 4 l 5
HANDLING INSTRUCTIONS
for DISPENSA VVS-x
2. Pull-out makes a (creaking) noise during opening and closing
2.1 Bottom runner dirty (due to dirt, foreign particles, lubricant)?
Wipe dry dirt off with a dry cloth. If there is oil or grease on the runner, you
will need to clean the whole element (running surfaces, roller surfaces and
rollers), e.g. with glass cleaner. The runner may need to be replaced.
Never use oil or other lubricants on the segments!
2.2 Fifth foot for cabinets 40 cm and wider?
For cabinets 40 cm and wider, check that the fifth foot is positioned centre front
and has been correctly adjusted/tightened. If the foot is not correctly installed,
the bottom panel may sag, causing noisy closing.
3. Soft close damping not working (option installed)
3.1 Is the top damper in place?
A damper can be ordered from the furniture manufacturer.
Install it in the frame so that it locks in position.
Damper
in place
Damper not
in place
3.2 Is the top damper locked in place?
Damper
locked in
place
Damper not
locked in place
Move damper until
it locks in place!