Standard Furniture OMAHA GRAY DR 16680 User manual

STANDARD
furniture
ASSEMBLY INSTRUCTION
GROUP NO.: 16680 OMAHA GRAY DR
ITEM NO.: 16696 - COUNTER HEIGHT TRESTLE TABLE W/2-13 FILLS
Read instruction carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment. Remove all
components from pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts
as specified below.
It is recommended to use two or more people during the assembly process.
HARDWARE LIST: PART LIST:
No. Description Sketch Size Qty'
1Long Bolt F 516'' x 60 mm 4 pcs
2Short Bolt F
14'' x 40 mm 2 pcs
3Lock Washer F 516'' x 13 mm 6 pcs
4Flat Washer F 516'' x 19 mm 6 pcs
5Short Screw F4 mm x 30 mm 12 pcs
6 Long Screw F4 mm x 60 mm 4 pcs
7Allen Key 4 mm 1 pc
No. Description Sketch Qty'
ATable Leg A 2 pcs
sticker stick under Leg
A
B
sticker stick under Leg
BTable Leg B 2 pcs
CSide Stretcher 2 pcs
DCenter Stretcher 2 pcs
EMounting Plate 1 pc
FTable Top 1 pc
A
B
B
C
C
6
Step 1
Step 1: Attach the Side Stretcher (C) to the middle of Table
Leg A (A) and Table Leg B (B) by using Long Screw (6),
tighten with Phillips screw drivers (not included).
A
BAB
E
Step 2 7
1
3
4
CC
Step 3 Step 4
Wood Dowel
7
2
3
4
5
A
B
D
AB
C
C
E
E
D
D
A
B
Step 4: Place the Table Top (F) upside down on a piece of cloth
or carpet to prevent finish from scratching. Align pre-drilled hole
on the Mounting Plate (E) to the Wood Dowel on the table slide.
Attach the assembly base in Step 4 to the Table Top (1) by using
Short Screw (5) and fully tighten with Phillips screw drivers (not
included).
5
A
B
B
A
D
C
C
E
F
Wood Dowel
The pre-drill
hole
GTable Leaf 2 pcs
Step 2: Attach the Table Legs are assembled in Step 1 to
Mounting Plate (E) by using Flat Washer (4), Lock Washer (3),
Long Bolt (1) and tighten with Allen Key (7).
Step 3: Attach the Center Stretcher (D) to the Side Stretcher (C)
by aligning the wood dowels to the pre-drilled holes on the Side
Stretcher (C) and tighten with Short Screw (5) by using Phillips
screw drivers (not included).
Attach the Center Stretcher (D) to the Mounting Plate (E) by
using Flat Washer (4), Lock Washer (3), Short Bolt (2) and
tighten with Allen Key (7).

STANDARD
furniture
Read instruction carefully prior to assembly.
Thank you for purchasing this quality product. Check carefully for small parts which may come loose during shipment. Remove all
components from pack and place top down on soft surface such as carpet or cloth to prevent scratching the finish. Identify and count all parts
as specified below.
It is recommended to use two or more people during the assembly process.
UNLOCK LOCK
Step 5: Unlock The Latch underneath the Table Top (F) and open the Table Top (F) by pulling from the both. Insert Table
Leaf (G) to right position follow the picture show. Close the Table Top (1) by pushing from both ends. Lock the Latch to
prevent from sliding.
G
F
G
Step 6: Assembly product is now completed.
Step 5
Step 6
G
G
F
B
A
C
D
A
B
C
Cleaning instructions: Clean using soft cloth
Made in Vietnam
ASSEMBLY INSTRUCTION
GROUP NO.: 16680 OMAHA GRAY DR
ITEM NO.: 16696 - COUNTER HEIGHT TRESTLE TABLE W/2-13 FILLS