Stanley ST-22-240-E User manual

Electric Fan Heater
ST-22-240-E / ST-23-240-E
STEA-434

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
2
PLEASE READ THE FOLLOWING INSTRUCTIONS
CAREFULLY BEFORE USING THE APPLIANCE.
- This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
- Children of less than 3 years should be kept away unless
continuously supervised. Children aged from 3 years and
less than 8 years shall only switch on/off the appliance
provided that it has been placed or installed in its intended
normal operating position and they have been given
supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user
maintenance.
- CAUTION: Some parts of this product can become very hot
and cause burns. Particular attention has to be given where
children and vulnerable people are present.
- If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
- The heater must not be located immediately below a
socket-outlet.
- Do not use this heater in the immediate surroundings of a
bath, a shower or a swimming pool.
- Do not use the appliance for other than its intended use. For
domestic indoor use only.
- Place the appliance on a at, stable, heat-resistant surface.
Operating the product in any other position could cause a
hazard.
- There may be trace of odour during the rst few minutes of
initial use. This is normal and will quickly disappear.
- Do not attempt to repair, disassemble or modify the
appliance. There are no user-serviceable parts inside.
- CAUTION – if using an extension lead please ensure you
do not exceed the maximum rated running wattage/load
of the extension lead.

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
3
Read the instruction manual: When this
symbol is marked on a product, it means that
the instruction manual must be read.
Do not use the appliance for other than its
intended use. For domestic indoor use only.
WARNING: In order to avoid overheating, do
not cover the heater.

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
4
ST-22-240-E / ST-23-240-E
2
4
6
7
8
1
3
5
1. Front Guard
2. Fan
3. Heat Coil
4. Power Light
5. Function Selector
6. Handle
7. Thermostat
8. Adjustment Knob (x2)

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
5
SPECIFICATIONS
Specications subject to change without notice
ST-22-240-E ST-23-240-E
RATED POWER INPUT (kW) 2.0 3.0
AIR FLOW (m3/h)158 217
HEATING AREA (m3 /m2)40/20 60/30
RATED VOLTAGE/FREQUENCY 220-240V~50Hz 220-240V~50Hz
HEAT SETTINGS 2 2
WEIGHT 1.7 kg 2.9 kg
APPLIANCE CLASS 1 1
INGRESS PROTECTION RATING (IP) IP20 IP20
FUNCTIONS / SETTINGS
Unit is Off
Fan Runs - No Heating
Fan Runs - Half Power Heating
Fan Runs - Full Power Heating
NOTE: The fan will run continuously while the heater is operating.

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
6
Safety Information
IMPORTANT: Read and understand all of the
safety information and instructions in this
manual before operating your heater.
RISK OF EXPLOSION! Do Not
operate this heater where there
are harmful, explosive or flam-
mable gasses, fumes or hazard-
ous substances.
DANGER
RISK OF FIRE! Do Not operate
this heater near combustible
materials.
WARNING
ELECTRIC SHOCK HAZARD!
Do not use this heater in the
immediate surroundings of a
bath, a shower, or a swimming
pool.
WARNING
BURN HAZARD! Do Not touch
the front of heater while it is
operating. This heater is hot
while operating.
WARNING

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
7
Children should be supervised so they do
not play with the appliance.
ALWAYS use only the electrical power
(voltage and frequency) specied on the
model plate of the heater.
ALWAYS use an extension cord properly
rated for this appliance.
ALWAYS ensure that all cords are
protected against short circuit and
overload.
ALWAYS keep power cord away from hot
air outlet.
ALWAYS disconnect heater from power
source when not in use.
NEVER place the heater on a small,
uneven or unstable surface that may
cause the heater to fall.
NEVER connect other appliances to the
same electrical outlet as the fan heater.
NEVER operate heater with heater guards
removed.
NEVER block hot air outlet while heater is
operating.
NEVER cover or obstruct heater.
NEVER use ducting with heater.
NEVER pull or carry heater by the power
cord.
NEVER use heater with an external
switching device: such as a timer.
If heater is damaged, do not use it. The
heater must be serviced by a qualified
person or service agent.
RISK OF INJURY! DO NOT
MOVE HEATER WHILE IT IS
OPERATING.
WARNING
STANLEY, The STANLEY Logo, The Notched Rectangle
and the Yellow and Black Diagonal Package Design
are all trademarks of Stanley Black & Decker, Inc. or an
affiliate thereof.

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
8
Operation
1. Position the fan heater so that it stands
upright on a rm, level surface and at
a safe distance from wet environments
and ammable objects.
2. Connect the fan heater to the proper
electrical power.
3. Set the thermostat dial to “+”.
4. The fan heater will switch on when the
function selector dial is set to one of the
power settings.
5. Once the room reaches the desired
temperature, turn the thermostat dial
back until heating element turns off.
6. Before you switch off the heater, please
turn the thermostat to “-” and turn
the switch to the fan position. Let the
appliance cool down for two minutes,
and only then turn off the heater and
pull out the plug from the power supply.
Automatic Overheat Safety Control
- This heater is equipped with safety
internal heat limiting thermostat and
overheat protection circuit. When a
potential overheat temperature is
reached, the system will automatically
shut the heater off.
Thermostat Instructions
- At rst, set the thermostat to “+” and let
the heater operate with full power input.
When the room temperature reaches
the required value, turn the thermostat
to the left until it switches off.
- The thermostat will then switch on and
off automatically to control the room
temperature according to the preset
value and keep the room temperature
constant.
- When using the heater for the rst time,
you may notice a slight emission of
smoke. This is quite normal and it stops
after a short time. The heating element
is made of steel and was coated with a
layer of protective oil during production.
The smoke is caused by the leftover oil
as it is heated.
Cleaning and Maintenance
- Before cleaning the appliance,
disconnect it from the outlet and let it
cool down.
- The enclosure is easy to get dirty. Wipe
it often with a soft sponge. For very
dirty parts, wipe with a sponge dipped
in < 50°C water and mild detergent,
then dry the heater enclosure with a
clean cloth. Be careful not to let the
water enter the inside of the appliance
- In order to protect the enclosure, don’t
splash water onto the heater, and never
use a solvent like gasoline, isoamyl
acetate, toluene, etc. to clean the
heater.
- When you store the heater, let it cool
down first and, keep it dry. Then cover
it with a plastic bag, put it in the packing
box and store it in a dry, ventilated
place.

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
9
RISK OF ELECTRIC SHOCK!
DISCONNECT FROM POWER
BEFORE MAINTENANCE.
WARNING
Plug Replacement
NOTE: This section only applies to heaters sold or used in Great Britain.
This appliance is supplied with a BS1363
3 pin plug tted with a fuse. Should the
fuse require replacement, it must be
replaced with a fuse with the proper amp
rating. (see Technical Specications page
5) and approved to BS1362.
In the event the mains plug has to be
removed/ replaced for any reason, please
note:
IMPORTANT: The wires in the mains
lead are colored in accordance with the
following code:
Blue – Neutral Brown – Live
Green/Yellow – Earth
As the colors of the wires in the mains
lead of this appliance may not correspond
with the colored markings identifying the
terminals in your plug, proceed as follows:
The blue wire must be connected to the
terminal marked with an N or colored
black. The brown wire must be connected
to the terminal marked with an L or
colored red. The green/ yellow wire must
be connected to the earthing terminal
which is marked with an E or with the
earth symbol.
NOTE: If a moulded plug is tted and
has to be removed take great care in
disposing of the plug and severed cable,
it must be destroyed to prevent engaging
into a socket.
Never
connect
live or neutral wires
to the earth termi-
nal of the plug.
WARNING

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
10
GREEN / YELLOW
Earth
BROWN
Live
FUSE
13 Amps
CORD CLAMP
BLUE
Neutral
Plug Replacement Wiring Diagram
Figure 3

© 2017, Obelis S.A Registered Address:
Bd. Général Wahis, 53 1030 Brussels, Belgium
NEVER LEAVE HEATER UNATTENDED WHILE
CONNECTED TO A POWER SOURCE
11
Problem Cause Solution
The heater does not run, even
when it is plugged in and the
thermostat is switched on
1. The plug is loose, bad
connection.
1. Pull out the plug, check
the connection of the plug
and socket. Then connect
again.
The heating element is glowing
1. The input voltage is too
high or too low
2. The air inlet grill is blocked.
1. Use correct power supply
stated on the rating label.
2. Keep the heater away from
items such as; plastic bags,
paper, and other items that
can cover the air inlet.
The appliance didn’t heat up,
only the ventilator worked.
1. The switch was not on a
heat setting
2. Desired room temperature
reached
3. The self-resetting cut-out
initiated
1. Turn the switch to the
desired heat setting
2. Thermostat will shut
off once desired room
temperature is reached.
Heater is operating
correctly.
3. Turn the heater off and
inspect the blockage of inlet
or outlet. Disconnect the
plug and wait at least 10
minutes for the protection
system to reset before
attempting to restart the
heater.
Abnormal noise. 1. The appliance is not
standing upright.
1. Place the heater on a level
surface.
Troubleshooting

Obelis S.A.
Registered Address:
Bd. Général Wahis, 53
1030 Brussels, Belgium
© 2017 Stanley Black & Decker, Inc.
Pinnacle Climate Technologies, Inc.
Sauk Rapids, MN 56379 USA
EC
REP