Stanley ST-302-231-A User manual

Electric Fan Heater
This product is only suitable for well insulated
spaces or occasional use.
ST-302-231-A
STEB-564

1
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Read the instruction manual: When this
symbol is marked on a product, it means that
the instruction manual must be read.
Do not use the appliance for other than its
intended use. For domestic indoor use only.
WARNING: In order to avoid overheating, do
not cover the heater.

2
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
PLEASE READ THE FOLLOWING INSTRUCTIONS
CAREFULLY BEFORE USING THE APPLIANCE.
- The appliance is not to be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
- Children being supervised should not play with the
appliance.
- Do not use this heater if it has been dropped.
- Do not use if there are visible signs of damage to the heater.
- Use this heater on a horizontal and stable surface, or x it to
the wall, as applicable.
- WARNING: Do not use this heater in small rooms when
they are occupied by persons not capable of leaving the
room on their own, unless constant supervision is provided.
- WARNING: To reduce the risk of re, keep textiles, curtains,
or any other ammable material a minimum distance of 1 m
from the air outlet.
- CAUTION: Some parts of this product can become very hot
and cause burns. Particular attention has to be given where
children and vulnerable people are present.
- If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
- The heater must not be located immediately below a socket-
outlet.
- Do not use this heater in the immediate surroundings of a
bath, a shower or a swimming pool.
- Do not use the appliance for other than its intended use. For
domestic indoor use only.
- Place the appliance on a at, stable, heat-resistant surface.
Operating the product in any other position could cause a
hazard.
- There may be trace of odour during the rst few minutes of
initial use. This is normal and will quickly disappear.
- Do not attempt to repair, disassemble or modify the
appliance. There are no user-serviceable parts inside.
- CAUTION – if using an extension lead please ensure you
do not exceed the maximum rated running wattage/load of
the extension lead.

3
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
1
2
3
4
6
7
5
ST-302-231-A
1. Front Guard
2. Fan
3. Heat Coil
4. Function Selector
5. Handle
6. Thermostat
7. Adjustment Knob

4
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
SPECIFICATIONS
Specications subject to change without notice
ST-302-231-A
THERMAL POWER
(kW) 2.0
HEATING AREA (m2) 20
POWER (Volt / Hz) 220-240 ~ 50
HEAT SETTINGS 1
FUNCTIONS / SETTINGS
Unit is Off
Fan Runs -
No Heating
Fan Runs - Full Power
Heating
NOTE: Heating element will shut off when desired
temperature is reached. Fan will run continuously. This heater is
equipped with a tip over switch. If this heater is overturned the
tip over switch will automatically turn it off.

5
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Safety Information
IMPORTANT: Read and understand all of the safety
information and instructions in this manual before
operating your heater.
RISK OF EXPLOSION! Do Not operate
this heater where there are harmful,
explosive or flammable gasses, fumes
or hazardous substances.
DANGER
RISK OF FIRE! Do Not operate this
heater near combustible materials.
WARNING
ELECTRIC SHOCK HAZARD! Do not
use this heater in the immediate sur-
roundings of a bath, a shower, or a
swimming pool.
WARNING
BURN HAZARD! Do Not touch the
front of heater while it is operating.
This heater is hot while operating.
WARNING
Risk Of injury! Do Not move heater
while it is operating.
WARNING
RISK OF ELECTRIC SHOCK!
DISCONNECT FROM POWER BEFORE
MAINTENANCE.
WARNING

6
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Children should be supervised
so they do not play with the
appliance.
ALWAYS use only the electrical
power (voltage and frequency)
specied on the model plate of
the heater.
ALWAYS use an extension cord
properly rated for this appliance.
ALWAYS ensure that all cords
are protected against short
circuit and overload.
ALWAYS keep power cord away
from hot air outlet.
ALWAYS disconnect heater from
power source when not in use.
NEVER place the heater on a
small, uneven or unstable surface
that may cause the heater to fall.
NEVER connect other
appliances to the same
electrical outlet as the fan
heater.
NEVER operate heater with
heater guards removed.
NEVER block hot air outlet while
heater is operating.
NEVER cover or obstruct heater.
NEVER use ducting with heater.
NEVER pull or carry heater by the
power cord.
NEVER use heater with an
external switching device: such as
a timer.
If heater is damaged, do not use
it. The heater must be serviced
by a qualified person or service
agent.

7
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
1
2 3
Assembly

8
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
4 5
6
Assembly

9
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Assembly (See Page 7-8)
1. Align holes in heater leg frame with
lower inner bracket.
2. Attach lower outer bracket to lower
inner bracket using screws.
3. Align lower inner bracket with side
support.
4. Attach side supports to heater using
tilt adjustment knob.
5. Slide side supports into upper
brackets, align holes and insert
screws to tighten.
6. Slide upper handle brackets onto front
handle, align holes and insert screws
to tighten.
7. Slide rear handle into upper handle
brackets, align holes and insert
screws to tighten.
Operation
1. Position the fan heater so that it
stands upright on a firm, level surface
and at a safe distance from wet
environments and flammable objects.
2. Connect the fan heater to the proper
electrical power.
3. Set the thermostat dial to the
maximum temperature.
4. The fan heater will switch on when
the function selector dial is set to one
of the three power settings.
5. Once the room reaches the desired
temperature, turn the thermostat dial
back until heating element turns off.
Automatic Overheat Safety Control
– This heater is equipped with safety
internal heat limiting thermostat and
overheat protection circuit. When a
potential overheat temperature is
reached, the system will automatically
shut the heater off.
Thermostat Instructions
– At first, set the thermostat to “+” and
let the heater operate with full power
input. When the room temperature
reaches the required value, turn the
thermostat to the left until it switches
off.
– The thermostat will then switch on
and off automatically to control the
room temperature according to the
preset value and keep the room
temperature constant.
– When using the heater for the first
time, you may notice a slight emission
of smoke. This is quite normal and it
stops after a short time. The heating
element is made of steel and was
coated with a layer of protective
oil during production. The smoke
is caused by the leftover oil as it is
heated.
Cleaning and Maintenance
– Before cleaning the appliance,
disconnect it from the outlet and let it
cool down.
– The enclosure is easy to get dirty.
Wipe it often with a soft sponge.
For very dirty parts, wipe with a
sponge dipped in < 50°C water and
mild detergent, then dry the heater
enclosure with a clean cloth. Be
careful not to let the water enter the
inside of the appliance
– In order to protect the enclosure,
don’t splash water onto the heater,
and never use a solvent like gasoline,
isoamyl acetate, toluene, etc. to clean
the heater.
– When you store the heater, let it cool
down first and, keep it dry. Then
cover it with a plastic bag, put it in
the packing box and store it in a dry,
ventilated place.

10
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Troubleshooting
Problem Cause Solution
Fan stays on when heat
shuts off.
1. Fan runs
continuously
while the heater is
operating.
1. Heater is operating
correctly.
Fan speed stays the
same when changing
settings.
1. Fan speed stays
constant. Setting
changes amount of
heat output only.
1. Heater is operating
correctly.
Heating element does
not glow red.
1. Heating element is
made of stainless
steel and will not
glow red to produce
heat.
1. Heater is operating
correctly.
Do not feel heat or air
ow.
1. No power to heater.
2. Desired room
temperature
reached.
3. Heater does not
heat area in front
of heater, it will
disperse heat
throughout room to
heat entire space.
1. Check power
connections /
connect heater to
power supply.
2. Thermostat will shut
off once desired
room temperature is
reached. Heater is
operating correctly.
3. Heater is operating
correctly.

11
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
ST-302-231-A
Exploded View

12
NEVER LEAVE HEATER UNATTENDED
WHILE CONNECTED TO A POWER SOURCE.
© 2021 Obelis S.A Registered Address:
Bd. Général Wahis, 53, 1030 Brussels, Belgium
Belgique et Luxemburg
België en Luxembourg
E. Walschaertstraat 14
2800 Mechelen
Belgium
www.stanleyworks.be
Enduser[email protected]
BE-NL= [phone]
BE-FR = [phone]
BE Fax: [phone]
Danmark Roskildevej 22
2620 Albertslund
www.stanleyworks.dk
[email protected]
Fax: [phone]
Deutschland Richard Klinger Str. 11
65510 Idstein
www.stanleyworks.de
[email protected]
Tel: [phone]
Fax: [phone]
Ελλάς Hμερος Τόπος 2 - Χάνι Αδάμ Ασπρόπυργος
-19300 -Αττική - Αττικής
www.stanley.gr
[email protected]
Τηλ: [phone]
Φαξ: [phone]
España Parque de Negocios“Mas Blau”
Edicio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
www.stanleyworks.es
[email protected]
Tel: [phone]
Fax: [phone]
France 5, allée des hêtres
BP 30084, 69579 Limonest Cedex
www.stanleyoutillage.fr
[email protected]
Tel: [phone]
Fax: [phone]
Schweiz
Suisse
Svizzera
In der Luberzen 42
8902 Urdorf
www.stanleyworks.ch
[email protected]
Tel: 044 - 755 60 70
Fax: 044 - 730 70 67
Ireland 210 Bath Road; Slough, Berks SL1 3YD UK www.stanleytools.co.uk
Tel: [phone]
Fax: [phone]
Italia Energypark–Building 03 sud,Via Energy Park
6 20871 Vimercate (MB)
www.stanley.it
Tel. [phone]
Fax [phone]
Nederlands Stanley Black & Decker Netherlands B.V.
Postbus 83
6120 AD Born
www.stanleyworks.nl
Enduser[email protected]
Tel : [phone]
NL Fax: [phone]
Norge Postboks 4613, Nydalen
0405 Oslo
www.stanleyworks.no
[email protected]
Fax: [phone]
Österreich Oberlaaerstrasse 248
A-1230Wien
www.stanleyworks.de
[email protected]
Tel: 01 - 66116 - 0
Fax: 01 - 66116 - 14
Portugal Quinta da Fonte - Edifício Q55 D. Diniz
Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo
2770 - 071 Paço de Arcos
www.stanleyworks.pt
[email protected]
Tel: [phone]
Fax: [phone]
Suomi PL 47
00521 Helsinki
www.stanleyworks.
customerservice.@sbdinc.com
Puh: 010 400 4333
Sverige Box 94
431 22 Mölndal
www.stanleyworks.se
[email protected]
Fax: [phone]
United Kingdom 210 Bath Road; Slough, Berks SL1 3YD www.stanleytools.co.uk
Tel: [phone]
Fax: [phone]
Hungary Rotel Kft.
1163 Budapest,Thököly út 17.
www.stanleyworks.hu
[email protected]
Tel [phone]
Fax[phone]
Czech Republic BAND SERVIS CZ s.r.o.
K Pasekam 4440
760 01 Zlín, Czech Republic
www.stanleyworks.cz
http://www.bandservis.cz
Tel.: [phone]
Fax.: [phone]
Slovakia BAND SERVIS s.r.o.
Paulinska 22
917 01 Trnava, Slovakia
www.bandservis.sk
Tel.: [phone]
Fax.: [phone]
Poland Erpatech
ul. Bakaliowa 26
05-080 Mościska
www.stanleyworks.pl
Tel.: [phone]
Fax.: [phone]
Slovenia G-M&M d.o.o.
Brvace 11
1290 Grosuplje Slovenija
www.g-mm.si
[email protected]
T: [phone]
F: [phone]
Cyprus IOANNOU J.
4A Ath.Diakou street
1046- Nicosia -Cyprus
[email protected]
Τel : [phone]
Fax : [phone]
Bosnia-Herzegovina G-M&M d.o.o.
Brvace 11
1290 Grosuplje
Slovenija
www.g-mm.si
[email protected]
T: [phone]
F: [phone]
Bulgaria TASHEV-GALVING LTD
68 KLIMENT OHRIDSKI BLVD.
1756 Soa, Bulgaria
www.tashev-galving.com
T: [phone]
F: [phone]
Croatia G-M&M d.o.o.
Brvace 11
1290 Grosuplje
Slovenija
www.g-mm.si
[email protected]
T: [phone]
F: [phone]
Estonia ASTallmac
Mustame tee 44,
EE-10621Tallinn
www.tallmac.ee/est
T: [phone]
F: [phone]
Latvia LIC GOTUS SIA
Ulbrokas Str.
LT - 1021 Rīga
www.licgotus.lv
T: [phone]
F: [phone]
Lithuania UAB ELREMTA OU
Neries kr. 16E
LT - 48402 Kaunas
[email protected]
T: [phone]
F: [phone]
Malta Energypark–Building 03 sud,Via Energy Park
6 20871 Vimercate (MB)
www.stanley.it
Tel. [phone]
Fax [phone]
Romania Stanley Black & Decker
Phoenicia Business Center
Strada Turturelelor, nr 11A, Etaj 6, Modul 15,
Sector 3 Bucuresti
www.stanleyworks.ro
T: +4021.320.61.04/05
F: +4037.225.36.84
Serbia G-M&M d.o.o.
Brvace 11
1290 Grosuplje
Slovenija
www.g-mm.si
[email protected]
T: [phone]
F: [phone]
SERVICE
STXA-819

Obelis S.A.
Registered Address:
Bd. Général Wahis, 53
1030 Brussels, Belgium
© 2021 Stanley Black & Decker, Inc.
Pinnacle Climate Technologies, Inc.
Sauk Rapids, MN 56379 USA
EC
REP