Star Headlight & Lantern Star Half Phantom ULB14 User manual

PLIT413 REV. F 1/3/20
With Gen 4 Starburst LEDs
Model ULB14
Undercover Interior LED Lig tbar
Star Half Phantom
Star Half PhantomStar Half Phantom
Star Half Phantom ™
Please Note: T ese instructions are provided as a general guideline only. Specific
mounting and/or wiring, may be necessary and are t e sole responsibility of t e
installer. Star Headlig t & Lantern Co., Inc. assumes no responsibility for t e
integrity of t e installation for t is or any of its products.

-1-
IMPORTANT: Please read all of the following instructions before installing your new
Split Phantom ™ LED undercover lightbar.
CAUTION: Please be sure to check that your cigarette plug outlet is properly fused.
Testing t e lig t before t is fuse is properly installed will void t e
warranty on t e lig t.
WARNING!!!! Care should be taken when positioning this warning light so that the light
and/or cord does not interfere with the proper operation of the driver-
side or passenger- side airbag! Failure to heed this warning may result
in serious or fatal injury.
tar Headlight & Lantern Co., Inc. assumes no
responsibility for the secure mounting of this light. It is the
responsibility of the installer and/or owner to ensure the
lightbar is mounted securely. Check your light every time
you enter the vehicle to ensure that it is mounted securely.
Before installing any of the brackets,
slide the enclosed rubber channel
over the front edge of the baffle .
Gasket Installation
Mounting
There are several optional mounting brackets that can be used to mount your Star Half
Phantom ™. Each light is packaged with the bracket that was selected at the time the light
was ordered. Please review the separate mounting instructions that are included with each
bracket. ou can visit www.star1889.com for a detailed list of available mounting brackets
and their known vehicle compatibility.

-2-
CA TION: Take extreme caution not to over tighten the screws!!! Over tightening
of the screws can strip the holes.
1. After the light has been mounted (see separate mounting instructions), if adjustments
permit, slide the light forward until the top of it is touching the windshield.
2. Loosen the baffle screws and carefully slide the baffle forward until the gasket is forced
slightly downward by the pressure of the windshield.
3. Tighten the Baffle Adjusting Screws to secure the baffle in place .
Baffle Adjustment
4. Once all of the brackets are securely tightened, check your mount to ensure the
desired angle is achieved. Stand in front of the vehicle and inspect the light through
the front windshield. The screws may be loosened slightly to allow for any final
adjustments necessary.

-3-
Operating Instructions
Pattern Select
The button in the left side of the light is the Pattern Select button. Each time this
switch-button is depressed, the Star Half Phantom will cycle to the next pattern.
The Star Half Phantom is designed with thirty-five different patterns (see next
page):
Indicator LED
Located on the bottom of the Star Half Phantom is an Indicator LED. When your
light is activated, this LED will light up.
This light may be optionally de-activated if you wish. To do this, while the light is
running, hold down the Pattern Select Button for approximately 12 seconds, until the
light flashes 4 times. This will disable (or enable) the indicator LED.
The Star Half Phantom is designed for simple operation using two switches. It has a
switched cig plug for On/Off control, and a Pattern Select Button.
Pattern Select
Switc ed
Cig Plug
All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load. Testing t e lig t before t is fuse is properly
installed will void t e warranty on t e lig t.

-4-
1 Slow Warn *
2 Fast Warn
3 Superfast Warn
4 Warn Fade
5 Pre-Pop Warn
6 All Singleflash
7 Alt. Tripleflash
8 All Tripleflash
9 Alt. Quadflash w/Post Pop
10 All Quadflash w/Post Pop
11 Alt. Quintflash
12 All Quintflash
13 Alt. Pre-pop Quintflash
14 All Flicker
15 Alt. PSU Flicker
16 One Side Pop, Other Side Rapid Fire
17 One Side Rapid Fire, Other Pop
18 Comet 1
19 Comet 2
20 Delta Omega (Flash Rate Sweep)
21 Slow Warn, Superfast Warn
22 All Singleflash, All Flicker
23 Alt. Double, ALT. Quad w/Post Pop
24 All Double, ALL. Quad w/Post Pop
25 Alt Double, Alt. Pre-Pop Quad, Alt. Quad w/Post Pop, Alt Flicker
26 All Double, All Quintflash, All Quadflash w/Post Pop, All Flicker
27 All Quadflash w/Post Pop, All Doubleflash, All Flicker
28 Alt. Pre-Pop Triple, Alt. Doubleflash, Alt Flicker **
29 Alt. Pre-Pops, Alt. Flicker, Superfast Warn
30 Delta Omega, All. Double, All. Flicker
31 One Side Steady---Other side Singleflash
32 One Side Steady---Other Side Short-Long
33 Warn Medium (Alt. Long Singleflash)
34 Alt. Short - Alt. Long
35 Cycle All
* Default Pattern #1
** Default Pattern #2
 If at anytime you would like to go directly to the Slow Warn (pattern #1), simply press,
and hold the pattern select button for approximately 3 seconds. When the LEDs
flash once, release the button and the light will be in the Slow Warn pattern.
 If you would like to place the light back into the default pattern (Pattern 28: Alt. Pre-
Pop Triple, Alt. Doubleflash, Alt Flicker), simply press and hold the pattern select
button until the LED’s flash twice (approx. 6 seconds). Then release the button and
the light should be in the default pattern.
 Toggle Mode: Pressing and holding the pattern select button until the LED’s flash
three times (approx. 9 seconds) will toggle the “steady side” for patterns 31 and 32.
Warning Lights Pattern List