Qlight S80AL User manual

1
S80AL
LED Steady/ Flashing Signal Light
S80AL - BZ - 220 - R
[Model
number] [Buzzer] [Voltage] [Color]
| | | |
• S80AL • (Blank)
- No buzzer type
• BZ
- Built-in buzzer type
• 12/24
- DC12V-24V
• 110 -AC110V
• 220 -AC220V
R-Red
A-Amber
G-Green
B-Blue
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the
product that would void the warranty.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
Ordering Specications Product Specications
Please scan the QR code for more
detailed product information.
www.qlight.com
90 dB
5030
44
• Protection rating : IP44
• Ambient operating temperature : -30°C to +50°C
Model
number
Voltage Current Certicate Weight Color
S80AL
DC12V-24V Max. 0.125A 0.26kg
R-Red
A-Amber
G-Green
B-Blue
AC110V 0.035A 0.35kg
AC220V 0.020A 0.35kg
※CE compliant : DC12V-24V

2
S80AL
4-Ø4 HOLES
Ø8 CABLE ENTRY
Ø83
84
127
43
72
113
105
50
60
88
Lens(AS)
Housing(ABS)
LED unit
Light Function
Selection
Reector
(Heat resistant ABS)
S80AL
Dimensions
(Units : mm)
• Power Wiring : In case of terminal type, power lines are connected to the terminals.
• This product can be wired regardless of polarity.
• For built-in buzzer type, there is a shared supply line for the buzzer and lighting element.
Wiring Instructions
DC AC
Power
Red
Black
White
Black Power
Fuse Fuse
Parts Denition/ Installation/ Light Function Selection
■ Parts Denition/ Installation ■ Light Function Selection
• Please refer to the diagram below to use light function switch
located inside the product.
• Default setting is set as steady LED function. During installation,
please select the desired light function according to your applica-
tion needs.
▶ L : Steady ▶ LF : Flashing

3
Mounting Hole Specications
• Machine holes on the mounting surface referring to the diagram below.
50
60
4-Ø4.5 HOLES
Min. Ø5 CABLE ENTRY
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP44.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP44), it may cause malfunction or damage to the product.
• In case of outdoor applications, installation in the upright position is suggested to minimize the e󰀨ect of rain on the product.
• For further information, please visit our website (www.qlight.com).
Installation
• Please mount xing board① to the mounting surface using bolts. Then, connect the power line of terminal box.
• Hook the rear of the mounting bracket of the product to the upper xing board②, then push the body against the xing board.
• After tightly attaching the product body to the mounting bracket, tighten the bolt at the bottom of the mounting bracket③.
ⴙ
ⴘ
ⴚ

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - S80AL - 2106A