Star Trac E-TR Service manual

Settings
STAR TRAC FITNESS 1 of 4 637-1371 Rev: A
Settings Definitions
E-TR and E-TRx (LED Display)
The display assembly contains two modes for settings.
•“Manager Mode”
•“Maintenance Mode”
In these modes, there are settings that can be changed for the club/facility or country for which the treadmill has been
installed. There are also technical settings which determine how the unit will perform.
Engaging Manager Mode
•From the idle screen (unit is powered on but not in a program), press and hold , then , then
.
The word “MANAGER” will temporarily show in the marquee window and then go to the first setting.
Engaging Maintenance Mode
1. From the idle screen (unit is powered on but not in a program), press and hold , then , then
.
The word “MAINTENANCE” will temporarily show in the marquee window, then go to the first setting.
Once in the Engineering Mode:
•will be used to move between the different settings.
•will be used to change the values for the settings.
•The saves any changes made or enters into the sub-menus (if applicable).
•is used to exit a sub-menus or exit the maintenance mode.

Settings
STAR TRAC FITNESS 2 of 4 637-1371 Rev: A
The Maintenance mode has a 30 second time limit after the last key has been hit. After 30 seconds, it will automatically
exit the Maintenance Mode.
Note: The Manager Mode has only limited settings to change where the Maintenance Mode contains all available settings.
In this document, we will cover the Maintenance Mode settings.
Next to the setting name is a letter (A). Each letter represents the type of setting it is.
A The setting can’t be changed.
B The setting can be changed manually.
CThe setting has fixed options which can be changed.
PThe setting is a calibration program.
SThe setting contains a sub menu.
TThe setting is a test mode.
XSetting must be set to a specific value and not changed.
Maintenance Mode Settings
MC1
A
This is the version of the “Primary” software in the display. It will show the version of software
as well as the Check Sum number. Example: MC1 V1.82A CKSM 1F2E
MC2
A
This is the version of the “Secondary” software in the display. It will show the version of
software as well as the Check Sum number. Example: MC2 V1.32A CKSM AFD6
Serial Number
B
This is the last five digits of the serial number. It is used for reference only and does not have
any warranty implications.
Operating Hours
A
This is the number of hours the product has been used.
Distance Logged
A
The number miles (km) that the treadmill has gone.
Units
C
Shows which unit of measurement is being used.
Options are:
•English (mph)
•Metric (km/h)
Time
B
The maximum number of minutes that a program can run. The time my may changed by the
facility. The range is from 5 – 99.
Weight
B
The default weight of a user when the ‘Quick Start’ program is used. This value is used in the
calorie count algorithm.
Language
C
The user interface language.
The options are:
•Set A – English, Spanish, French, German, Portuguese
•Set B – English, Dutch, Swedish, Italian, Katakana
METS
C
A MET is a “Metabolic Equivalent” which is another way of measuring exercise effort. This
option can be turned ‘on’ or ‘off’.
Pause Duration
C
The amount of seconds that the pause mode will last.
The options are:
•30
•45
•60
•90
•120
Auto Fans
C
Auto Fans will turn the fans on automatically at after one minute into the work out. This function
can be turned ‘on’ or ‘off’.
Elevation
C
This settings allows the elevation to be turned off (if there were an issue) so users can still run
on treadmill. This function can be turned ‘on’ or ‘off’.
Auto Stop
X
This option must always be set to OFF. Turning this option ‘on’ may cause the running belt
to stop on users prematurely.

Settings
STAR TRAC FITNESS 3 of 4 637-1371 Rev: A
CSAFE
C
Allows the CSAFE port to be turned on for external systems like Fitlinxx. This option can be
turned ‘on’ or ‘off’.
PVS
C
Valid only on Version 1 PVS screens.
Lock Out
C
The lock out function allows the treadmill to be disabled unless the Lock Out ID code is
entered. This function can be turned ‘on’ or ‘off’.
Lock Out ID
B
This is the Lock Out ID code used to make a treadmill functional if the Lock Out is turned on.
The default Lock Out ID is 54321. Note: This code can be changed.
Minimum Speed
B
This determines what the minimum start up speed will be. The range is between .5 mph – 2.0
mph (.8 km/h - 3.2 km/h)
Maximum Speed
B
This determines what the maximum speed will be. The range is 5.0 mph – 15.0 mph (5.0 km/h
– 24.0 km/h)
Acceleration Time
B
This determines the amount of time, in seconds, that it takes the running belt to go from the
minimum speed to the maximum speed. 25 – 60
Deceleration Time
B
This determines the amount of time, in seconds, that it takes the running belt to go from the
maximum speed to stop. 20 – 60
Model
C
Should be set to the model of the treadmill for which the display is on. This will automatically
set some of the key settings to for the model to which it is set.
Date
B
This should be set to the month and year that the treadmill was manufactured. Example: 12.10
would be December 2010. This is used as a reference only.
Stop Switch
X
This must always be set to ‘E-STOP’. If set to ‘Lanyard’, the treadmill will not function.
Last Deck
B
This is the number of miles or km since the deck has been flipped or replaced. This is for
reference only.
Last Belt
B
This is the number of miles or km since the running belt has been replaced. This is for
reference only.
Program Stats
S
Programs Stats has a sub-menu containing all the programs and the a counter for how many
times each program has been used.
Note: Some of the programs listed are not available for all models.
The programs are:
•Quick Start
•Manual
•Alpine Pass
•Random Hill
•5K Loop
•Dynamic HR
•Constant HR
•
Fitness Test
•Firefighter
•USMC Test
•US Army Test
•Navy Test
•USAF Test
LED Test
T
This is a test used to verify that all the LED (lights) on the display are operational.
Keypad Test
T
This is a test used to verify that all the keys are responding on the display.
Heart Rate Test
T
This is a test used to verify that the contact and/or telemetry heart rate is working.
Serial Port Test Manufacture test only.
Error Stats
S
Error Stats has a sub menu containing all the error codes and a counter for how many times
each error code has occurred.
The errors are:
•Key Down
•Check Motor System
•Check Speed System
•No Rail Stop
•Speed Change
•
Elevation Stall
•Elevation Range
•Elevation Lost
•Fuse Bits Error
Last Error List
S
The Last Error List has a sub menu for the last 5 errors that have occurred on the treadmill as
well as other details about how the treadmill was performing at the time of the error.

Settings
STAR TRAC FITNESS 4 of 4 637-1371 Rev: A
Calibration Values
S
Calibration Values has a sub menu of settings that are related specifically to elevation or speed
calibration.
10 Rev
B
This the distance (in inches) that the running belt moves for ever ten rotations
of the flywheel. This number is critical for accurate speed calculations.
CNT/RV
X
This is the number of counts (of the RPM sensor) that equal one revolution of
the flywheel (which is 31). This number must never change.
Minimum
PWM XThis is the PWM number at the minimum speed. This number is set during
motor calibration.
½ Maximum
X
This is the PWM number at half the max speed. This number is set during
motor calibration.
Maximum
PWM XThis the PWM number at the maximum speed. This number is set during
motor calibration.
Person Detect
1 XThis setting has no function.
Person Detect
2 XThis setting has no function.
Person Detect
3 XThis setting has no function.
Elevation Zero
BThis is the incline value of the elevation motor at 0% elevation.
Elevation Max
BThis is the incline value of the elevation motor at max elevation.
Motor Calibration
P
This is the program that is run to calibrate the drive motor for steady transitions between
speeds.
Elevation Calibration
P
This is the setting used to calibrate the minimum and maximum calibration values.
Burn In Mode
X
Manufacture test only.
CCB
A
When a PVS CCB is properly connected, the version of software in the CCB will be display.
USB
A
When a PVS CCB is properly connected, the version of software for the USB is displayed.