Star Pro-Max GR14SPT-240V User manual

®
®
®
®
SPLIT LID TABLE TOP
TWO SIDED TOASTER
MODEL
GR14SPT-240V
GR14SPTK-240V
Installation and
Operation
Instructions
2M-Z4319 Rev. E 06/19
GR14SPT
®

2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not
responsible for errors or omissions in information provided or conclusions
provided, the user assumes all risks in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it
ready when you call to ensure a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Business 8:00 am to 4:30 p.m. Central Standard Time
Hours:
Telephone: [phone]
Fax: [phone]
E-mail [email protected]
Website: www.star-mfg.com
Service Help Desk
Authorized Service Agent Listing
Reference the listing provided with the unit
or
for an updated listing go to:
Website: www.star-mfg.com
E-mail [email protected]
Mailing Address: Star Manufacturing International Inc.
265 Hobson Street
Smithville, TN 37166
U.S.A

3
GENERAL INSTALLATION DATA
CAUTION
This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor for
use directly by the general public in food service locations.
INSTALLATION
1. Plug unit into dedicated 240 V.A.C. line with 15AMP receptacle.
2. DO NOT plug into 120V line. Doing so will damage the unit and void the warranty.
3. Each machine has been properly wired and inspected at the factory for operation on the
 voltageandtypeofcurrentspeciedonthenameplate.
CAUTION
DO NOT CONNECT TO ANY TYPE OF CURRENT OTHER THAN 240 V.A.C. OR THE
MACHINE WILL BE SERIOUSLY DAMAGED.
INITIAL START UP
Beforeusingtheunitforthersttime,cleanandheatforapproximately45minutes.
DO NOT ADJUST TIME AND TEMPERATURE
Theunittimeandtemperatureispresetbythefactorytothespeciccustomerrequirements
foratbread,burritos,quesadillasandcleaning.
The preset time and temperatures are:
Left Display:
Button Number Time Temperature
1 15sec. 505°F
2 27sec. 505°F
3 35sec. 505°F
4 (Cleaning) 00sec. 275°F
Right Display:
Button Number Time Temperature
1 15sec. Same as Left
2 27sec. Same as Left
3 35sec. Same as Left
4 00sec. Same as Left
Ifadjustmentsarerequiredforadditionalfoodproducts,pleaserefertothetimeor
temperature programming section in this manual.
OPERATING INSTRUCTIONS
1. Turnunitonbyplacingswitchin"ON"position.The"HeatOn"indicator,program 
numberanddisplaywillashindicatingunitisheating.Whenthepresettemperatureis
reached,theheatinglight,displayandprogramlightindicatorwillstopashingfollowed
by 3 beeps. (Initial startup heating time is approximately 30 minutes).
2 Place product on the bottom cooking surface of the unit and close the lids.
3. Press program button and let displayed time count down to "0" at which time unit will
beep.Toturnoffthebeeper,pressprogrambuttonagain.
4. Raiselidsuntilitengagesintorstdetentandremovefood.Usingspatula,scrape
residue into grease catcher tray.
 Note:Metalutensilsmaybeused,however,usingnonmetalutensilswillprolongthelife
of the cooking surface.
5. Turn the unit off when not in use.

4
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Startup:
1. Thepresettimewillashuntilpresettemperatureisreached.
2. Whenthecontrolreachespresettemperature,timedisplay,"HeatOn"indicatorand
programindicatorwillstopashingandthealarmwillbeepthreetimes.
Temperature:
1. Toviewtheactualtemperature,pressandhold"TempButton".Displaywillread"LoF"
if temperature is below 273°F and "Hi F" if temperature is above 573°F.
To Program Time and Temperature:
1. Press and hold "TEMP" (actual temperature displays).
2. Whileholding"TEMP",pressandholdanyprogrambuttonontheLeftonesecond,the
LED above the program number light and the display reads "_ _ _ _".
Enterthefour-digitsecuritycodesequence,4, 3, 2, 1. The security code will not
showondisplay.Oncethecorrectsequencehasbeenentered,thepresettimewillbe
displayedandtheLEDforthatprogramwillbegintoash.
3. Set the time with the "+ or -" buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the "+ or -" buttons.
7. Press the "TEMP" button to save temperature and to exit programming mode
for this program. TheLEDwillstopashingbutwillremainlit.
8. Press any other program button within 15 seconds to continue programming without re-
entering the security code.
9. Whileprogrammingaprogram(LEDisashing),ifnoinputisreceivedfor15seconds,
the unit will revert to normal operation and the security code must be re-entered.
Note: Temperature settings are done with the Left side buttons only. The time settings
programmed on the Left buttons will also be programmed onto the Right side. See below to
make time changes to the Right side only. Each programming change must be saved by
pressing the "TEMP" button!
Right Side (Timer only):
1. ToChangethetimeonRight,pressandholdthe"TEMP"button,andpressandhold
any program button on the Right for one second. The LED above the program button
will light and the Right Display will read "_ _ _ _". Enter the four-digit security code
sequence,4, 3, 2, 1. The security code will not show on display. Once the correct
sequencehasbeenentered,thepresettimewillbedisplayedandtheLEDforthat
programwillbegintoash.
2. Set the time with the "+ or -" buttons.
3. Press the "TEMP" button to save the time.
4. TheLEDwillstopashingbutwillremainlit.
5. Press any other program button within 15 seconds to continue programming without
re-entering the security code.
6. Whileprogrammingaprogram(LEDisashing),ifnoinputisreceivedfor15seconds,
the unit will revert to normal operation and the security code must be re-entered.
Operation:
1. Pressing any program button (1-4) will start the timer countdown and display the preset
time remaining. The LED for the appropriate program will be lit during countdown and
remain lit until another program is selected.
2. Whenthedisplayreaches"00:00",thebuzzerwillsoundandthedigitswillash.
3. Presstheprogrambuttontosilencethebuzzerandreturnthereadouttoprogrammed
time.
4. The Right and Left sides will operate independent of each other. Both timers can be in
operation at the same time. The "00:00" display will show which side is timed out.

5
MONTHLY INSPECTION
Check all bolts/screws and tighten if necessary.
CLEANING
Allsurfacesexceptthecookinggridsarestainlesssteelandcanbecleanedwithawarm,
damp cloth and detergent.
CAUTION
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER.
DO NOT HOSE DOWN.
KEEP AWAY FROM RUNNING WATER.
DO NOT SPLASH CONTROL HOUSING!
DO NOT PUT ICE ON COOKING SURFACE.
Do not splash conduit connecting top and bottom of the toaster!!
CAUTION
For models with #4 programmed for "CLEAN" mode:
1. Press #4 button.
2. Open toaster to allow faster cooling.
3. Alarm will sound when toaster is 275° F.
4. Turn unit OFF.
5. Unplugtheunit.
6. Begintoastercleaningprocedureusinganswersystembook5,undertoaster.
BEFORE CLEANING ALL OTHER UNITS MAKE SURE POWER IS TURNED
OFF AND UNIT IS UNPLUGGED.
To remove burned on grease or food residue use the following mixture:
1 Tablespoon liquid dish detergent
1 Cup of warm water
Whileholdingtoplidwithonehand,applythismixturetocoldorwarmtopcookingsurface
withaspongeorplasticscrubbingpad.Wipewithcleanspongeortoweluntilitisclean.
Empty and clean grease catcher tray as required using detergent and water after removing
tray from unit.

6
STAR MANUFACTURING INTERNATIONAL, INC.
SK1857 REV. B 6/30/11
MODEL 9D-GR14SPT-240
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
WIRE DIAGRAM, 240V, 2300 WATT
(2J-Z3263 CONTROLLER)
4
8
6 2
1 0
BA
C
D
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
GREEN
BLACK
WHITE
1
3
2
3
4
2
1
4
10
9
10
9
8
77
8
11
12
11 12
14
15
13
16
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
84
6 2
SWITCH
(INTERRUPTOR)
5
6
15 AMP, NEMA 6-15P PLUG
15
16 13
14
6
5
REAR OF CONTROLLER
E1 E4
E2
E11
E12
E3
E7 E6 E5
230V UNITS
L
N
G
19
18 20

7
STAR MANUFACTURING INTERNATIONAL, INC.
SK1856 REV. A 6/30/11
MODEL 9D-GR14SPT-CUL
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
WIRE DIAGRAM, 120V, 2300 WATT
(2J-Z3263 CONTROLLER)
4
8
6 2
1 0
BA
C
D
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
GREEN
BLACK
WHITE
1
3
2
3
4
2
1
4
10
9
10
9
8
77
8
11
12
11 12
14
15
13
16
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
84
6 2
SWITCH
(INTERRUPTOR)
5
6
30 AMP, NEMA 5-30P PLUG
15
16 13
14
6
5
REAR OF CONTROLLER
E1 E4
E2
E11
E12
E3
E7 E6 E5

8
FLAT
BREAD
12
QUES
3
CLEAN
4
TIME/TEMP
1
FLAT
BREAD QUES
234
TEMP
TIME/TEMP
ON
HEAT
OFF
ON
41
43
41
33
22
4
48
5
36
12
35
37 10
1
3
32
47
28
24
39
7
15
25
27
45
217
26
11
16
21
18
6
40
46
34
20
23
19
14
38
8
44
30
9
13
50
51
52
45
Nameplate
STAR MANUFACTURING INTERNATIONAL, INC.
MODEL - GR14SPT
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
SK1750 REV. E 3/22/06
55
54
57
52
53
56
51
49

9
PARTS LIST October13,2010,Rev.D
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
1
2
Some items are included for illustrative purposes only and in certain instances may not be available.
MODEL
Star Manufacturing International, Inc.
GR14SPT-240V SPLIT LID TABLE TOP
CLAM SHELL TOASTER
Fig No Part No Qty Description Application
1 D9-GR0032 2 TORQUE BOX ASSEMBLY
2D9-GR0150 1GREASE CABINET ASSEMBLY
D9-GR0034 GREASE CABINET ASSY GR14SPTK
3D9-GR0152 1BODY ASSEMBLY
4D9-GR0177 1 BURN GUARD ASSEMBLY - LEFT
5D9-GR0176 1 BURN GUARD ASSEMBLY - RIGHT
6D9-GR0156 1REAR PLATE ASSEMBLY
7D9-GR0518 1GREASE DRAWER ASSEMBLY
D9-GR0517 GREASE DRAWER ASSY. -STD GR14SPTK
8D9-GR0182 2 TOP RETAINING PLATE ASSEMBLY
9 PART OF ITEM #34
10 2A-Y6142 4 SLEEVE HANDLE
11 2A-Z11501 4 FOOT 1” SOLID RUBBER
12 2B-Z3336 414” GR14SPT ARM
2B-Z10355 ARM, CG/GR14SPT W/45° FRONT GR14SPTK
13 2C-Z3200 4 PIN - TOP HOUSING
14 2C-Z3350 2 HALF CLAMP - .188 DIA.
15 2E-Z3808 1SWITCH TOGGLE
16 2E-05-07-0350 1 TRANSFORMER 230V/10V 6VA
17 D9-GR0194 1 CORD POWER
18 2E-Z2894 1 TERMINAL BLOCK (304)
19 D9-Z3903 2 BRACKET, PROBE MOUNT
20 2E-Z3278 2 RTD PROBE - 48” LONG WIRE
21 2E-Z22595 2 RELAY DBL POLE-SNGL THR
21 2E-Z22595 1 RELAY DBL POLE-SNGL THR GR14SPTK
22 PS-GR0361 1 KIT, 2F-Z1945 CASTING, SM. BOT., ALUM.
23 PS-GR0356 2 KIT, 2F-Z3237 CASTING - TOP
24 2I-05-07-0013 1 BOOT SWITCH
25 D9-GR0664 1TIME/TEMP CONTROL-HARDWARE GR14SPT
D9-GR0380 TIME/TEMP CONTROL F/C GR14SPTK
26 2K-Y6764 1 BUSHING 90 SR 17-2
27 2K-Z1971 14 SPACER
28 2M-Z18461 1 LABEL ON & OFF
30 2M-Z2620 2 LABEL CAUTION, BI-LINGUAL
31 2M-Z2764 1 LABEL-PATENT PENDING
32 2M-Z3337 1OVERLAY
2M-Z10087 OVERLAY GR14SPTK
33 2N-Z9327 1 ELEMENT, HEATING, 1300 W
34 PS-Z9326 2 ELEMENT, HEATING, TOP 500W
35 2R-Z3345 1 COUNTER BALANCE - SPLIT TOP
36 2V-Z3152 2 HANDLE - TACO BELL 2
37 2V-Z3252 2 TOP HOUSING LATCH ROD
Models After 06/2019
Models before 06/2019 use PS-GR0839
1
1
1
1

10
GR14SPT-240V SPLIT LID TABLE TOP
CLAM SHELL TOASTER
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
INCLUDE MODEL AND SERIAL NUMBER OF
2
2
PARTS LIST November18,2009,Rev.D
Some items are included for illustrative purposes only and in certain instances may not be available.
MODEL
Star Manufacturing International, Inc.
Fig No Part No Qty Description Application
38 B9-04-WB-0046 2 CLAMP WIRE SUPPORT
39 D9-GR0151 1 FACEPLATE ASSEMBLY
40 D9-Z2133 2INSULATION FIBERGLAS TOP
41 D9-Z2618 1 BTM ELEMENT RET. PLATE
42 D9-Z2619 1 BTM INSULATION RET. PLATE
43 D9-Z2888 1 INSULATION - 14”
44 D9-GR0181 2 TOP HOUSING & CONDUIT AY.
45 D9-Z3259 1 BASE BOTTOM
46 D9-Z3902 2 PLATE - TOP ELEMENT RET.
47 Z1-70-07-0343 1 SWITCH GUARD
48 D9-GR0189 2 TOP BURN GUARD AY.
49 D9-GR0183 1INSULATION BAFFLE AY.
50 D9-Z3826 1 INSULATION - BAFFLE

11
LIMITED EQUIPMENT WARRANTY
Star Manufacturing [as well as its subsidiaries,
Toastmaster and Holman] warranties new products to
be free from defects in material and/or workmanship
for a period of one [1] year from the date of original
installation, except as noted below. Defects that
occur as a result of normal use, within the time period
and limitations defined in this warranty, will at Star’s
discretion have the parts replaced or repaired by Star or
a Star-authorized service agency.
THIS WARRANTY IS SUBJECT TO ALL LISTED CONDITIONS.
Repairs performed under this warranty are to be
performed by a Star authorized service agency. Star
will not be responsible for charges incurred or service
performed by non-authorized repair agencies. In all
cases, the nearest Star-authorized service agency must
be used. Star will be responsible for normal labor charges
incurred in the repair or replacement of a warrantied
product within 50 miles (80.5 km) of an authorized
service agency. Time and expense charges for anything
beyond that distance will be the responsibility of the
owner. All labor will need to be performed during regular
service hours. Any overtime premium will be charged
to the owner. For all shipments outside the U.S.A. and
Canada, please see the International Warranty for specific
details. It is the responsibility of the owner to inspect and
report any shipping damage claims, hidden or otherwise,
promptly following delivery. No mileage or travel charges
will be honored on any equipment that is deemed
portable. In general, equipment with a cord and plug
weighing less than 50 lb. (22.7 kg) is considered portable
and should be taken or shipped to the closest authorized
service agency, transportation prepaid.
PORTABLE EQUIPMENT EXAMPLES
WARRANTY EXCLUSIONS
THE FOLLOWING WILL NOT BE COVERED UNDER WARRANTY.
• Any product which has not been used, cleaned,
maintained, or installed in accordance with the directions
published in the appropriate installation sheet and/
or owner’s manual as well as national and local codes,
including incorrect gas, electrical, or water connection. Star
is not liable for any unit which has
been mishandled, abused, misapplied, subjected to
chlorides, harsh chemicals, or caustic cleaners, damaged
from exposure to hard water, modified by unauthorized
personnel, damaged by flood, fire, or other acts of nature
[or God], or which have an altered or missing serial number.
• Installation, labor, and job checkouts, calibration of heat
controls, air and gas burner/bypass/pilot adjustments, gas
or electrical system checks, voltage and phase conversions,
cleaning of equipment, or seasoning of griddle surface.
• Replacement of fuses or resetting of circuit breakers,
safety controls, or reset buttons.
• Replacement of broken or damaged glass components,
quartz heating elements, and light bulbs.
• Labor charges for all removable parts in gas charbroilers
and hotplates, including but not limited to burners, grates,
and radiants.
• Any labor charges incurred by delays, waiting time, or
operating restrictions that hinder a service technician’s
ability to perform service.
• Replacement of items subject to normal wear or items
that can easily be replaced during a daily cleaning routine,
such as but not limited to knobs, bulbs, fuses, quartz
heating elements, baskets, racks, and grease drawers.
• Components that should be replaced when damaged
or worn, but have been field-repaired instead [eg. field-
welded fry pots]
• Any loss of business or profits.
PRODUCTS PARTS LABOR
Star-Ultra Max® fryers, griddles,
charbroilers, and hotplates
2 years 2 years
Star-Max® fryers, griddles, char-
broilers, and hotplates 2 years 2 years
Jetstar® popcorn poppers 2 years 2 years
Staltek™ roller grill coatings 5 years
Cast iron grates, burners; and
burner shields 180 days
Star, Toastmaster, or Holman
parts sold to repair equipment 90 days
Service First 1 year
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty. 2M-Z21647 ∙ Rev. E ∙ 01.2019
• 514LL fryer
• 15MC and 18MCP hot food
merchandisers
• QCS1, QCS2, and RCS2 toasters
• 16PD-A pretzel merchandisers
• Condiment dispensers
except HPD- and SPD-series
models
• All pop-up toasters
• All pastry display cabinets
• All heat lamps
• J4R popcorn machine
• 12NCPW and 15NCPW nacho
merchandisers
• Nacho cheese warmers
except 11WLA-series models
• Specialty food warmers
except 130R, 11RW, and 11WSA
models
• All butter dispensers
• All nacho chip merchandisers
• All accessories
CONTACT
Should you require any assistance regarding the
operation or maintenance of any Star equipment;
write, phone, fax or email our service department. In
all correspondence mention the model number and
serial number of your unit, as well as the voltage or
type of gas you are using.
Business hours are 8:00 a.m. to 4:30 p.m. Central
Standard Time (CST)
Telephone: [phone]
Fax: [phone]
Email: Customerservic[email protected]om
www.star-mfg.com

12
STAR MANUFACTURING INTERNATIONAL INC.
Star - Holman - Lang - Wells - Toastmaster
265 HOBSON ST. SMITHVILLE, TN 37166
[phone]
www.star-mfg.com